Nicad/NiMH Charger
Description: This device is built around a PIC12F675 (a dandy little part from Microchip). The number of cells (1 to 8) is programmed in using the one button. The cell count is saved in EEPROM the next time you power up the device. Using just one button for all operations is a bit tricky, but easy once you try it a few times. There are 2 types of button operations: Hit (less than 1 second), and Hold (over 1 second). Here is what to do. Apply power (12 to 24 volts DC) to the jack. Then, connect the batteries. The green light comes on (indicating power applied) The red light flashes once for each cell.
Hit the button to display the cell count again. -or- Hold the button until you see one flash of the red light. -then- Hit the button to enter the program mode - one flash of the red light. -then- Hit the button once for each cell - light flashes for each hit. -then- Hold the button to store count and return to start -or- Hold the button until the red light comes on steady - unit will start charging. -then- Wait for charge to end. -or- Hold down to return to start.
During charging the red light 'winks' out about once per second for each volt short of a full charge. The result is that it flashes faster as full charge is approached. A timeout is provided if full charge is not achieved after several hours.
Once full charge is complete. The red light repeatedly flashes once and a small charge current (short pulse) is applied to the batteries. Two flashes indicates that the unit timed out.
The device utilizes a Microchip PIC12F675 microcontroller, which is responsible for managing the operation of the battery charging system and the user interface through a single button. The power supply range of 12 to 24 volts DC is suitable for various battery configurations, specifically accommodating between 1 to 8 cells.
The operational logic begins upon power application, indicated by the illumination of a green LED, which signifies that the device is powered and ready for interaction. The red LED serves a dual purpose: it provides feedback on the number of cells programmed and indicates the charging status.
The user interacts with the device through two distinct button actions: a short press (Hit) and a long press (Hold). The Hit action allows the user to quickly check the current cell count, while the Hold action initiates a programming mode. In this mode, the user can increment the cell count by pressing the button, with each press resulting in a corresponding flash of the red LED. To save the programmed cell count, the user must hold the button again, which stores the value in the microcontroller's EEPROM, ensuring that the configuration is retained across power cycles.
When the device is switched to charging mode, the red LED provides visual feedback on the charging progress. It flashes at a rate proportional to the voltage deficit from a full charge, allowing users to monitor the charging status intuitively. If the charging process surpasses a predetermined timeout period without reaching full charge, the system will indicate this failure through a specific LED flash pattern.
Upon successful completion of the charging cycle, the red LED emits a consistent flash pattern, signaling that a small pulse of current is being delivered to the batteries, which helps maintain their charge. The device is designed to be user-friendly, with a clear feedback mechanism through LED indicators and a streamlined button interface that simplifies operation while ensuring effective battery management.This device is built around a PIC12F675 (a dandy little part from Microchip). The number of cells (1 to 8) is programmed in using the one button. The cell count is saved in EEPROM the next time you power up the device. Using just one button for all operations is a bit tricky, but easy once you try it a few times. There are 2 types of button operations: Hit (less than 1 second), and Hold (over 1 second). Here is what to do. Apply power (12 to 24 volts DC) to the jack. Then, connect the batteries. The green light comes on (indicating power applied) The red light flashes once for each cell. -start- Hit the button to display the cell count again. -or- Hold the button until you see one flash of the red light. -then- Hit the button to enter the program mode - one flash of the red light. -then- Hit the button once for each cell - light flashes for each hit. -then- Hold the button to store count and return to start -or- Hold the button until the red light comes on steady - unit will start charging. -then- Wait for charge to end. -or- Hold down to return to start. During charging the red light 'winks' out about once per second for each volt short of a full charge.
The result is that it flashes faster as full charge is approached. A timeout is provided if full charge is not acheived after several hours. Once full charge is complete. The red light repeatedly flashes once and a small charge current (short pulse) is applied to the batteries. Two flashes indicates that the unit timed out.
Hit the button to display the cell count again. -or- Hold the button until you see one flash of the red light. -then- Hit the button to enter the program mode - one flash of the red light. -then- Hit the button once for each cell - light flashes for each hit. -then- Hold the button to store count and return to start -or- Hold the button until the red light comes on steady - unit will start charging. -then- Wait for charge to end. -or- Hold down to return to start.
During charging the red light 'winks' out about once per second for each volt short of a full charge. The result is that it flashes faster as full charge is approached. A timeout is provided if full charge is not achieved after several hours.
Once full charge is complete. The red light repeatedly flashes once and a small charge current (short pulse) is applied to the batteries. Two flashes indicates that the unit timed out.
The device utilizes a Microchip PIC12F675 microcontroller, which is responsible for managing the operation of the battery charging system and the user interface through a single button. The power supply range of 12 to 24 volts DC is suitable for various battery configurations, specifically accommodating between 1 to 8 cells.
The operational logic begins upon power application, indicated by the illumination of a green LED, which signifies that the device is powered and ready for interaction. The red LED serves a dual purpose: it provides feedback on the number of cells programmed and indicates the charging status.
The user interacts with the device through two distinct button actions: a short press (Hit) and a long press (Hold). The Hit action allows the user to quickly check the current cell count, while the Hold action initiates a programming mode. In this mode, the user can increment the cell count by pressing the button, with each press resulting in a corresponding flash of the red LED. To save the programmed cell count, the user must hold the button again, which stores the value in the microcontroller's EEPROM, ensuring that the configuration is retained across power cycles.
When the device is switched to charging mode, the red LED provides visual feedback on the charging progress. It flashes at a rate proportional to the voltage deficit from a full charge, allowing users to monitor the charging status intuitively. If the charging process surpasses a predetermined timeout period without reaching full charge, the system will indicate this failure through a specific LED flash pattern.
Upon successful completion of the charging cycle, the red LED emits a consistent flash pattern, signaling that a small pulse of current is being delivered to the batteries, which helps maintain their charge. The device is designed to be user-friendly, with a clear feedback mechanism through LED indicators and a streamlined button interface that simplifies operation while ensuring effective battery management.This device is built around a PIC12F675 (a dandy little part from Microchip). The number of cells (1 to 8) is programmed in using the one button. The cell count is saved in EEPROM the next time you power up the device. Using just one button for all operations is a bit tricky, but easy once you try it a few times. There are 2 types of button operations: Hit (less than 1 second), and Hold (over 1 second). Here is what to do. Apply power (12 to 24 volts DC) to the jack. Then, connect the batteries. The green light comes on (indicating power applied) The red light flashes once for each cell. -start- Hit the button to display the cell count again. -or- Hold the button until you see one flash of the red light. -then- Hit the button to enter the program mode - one flash of the red light. -then- Hit the button once for each cell - light flashes for each hit. -then- Hold the button to store count and return to start -or- Hold the button until the red light comes on steady - unit will start charging. -then- Wait for charge to end. -or- Hold down to return to start. During charging the red light 'winks' out about once per second for each volt short of a full charge.
The result is that it flashes faster as full charge is approached. A timeout is provided if full charge is not acheived after several hours. Once full charge is complete. The red light repeatedly flashes once and a small charge current (short pulse) is applied to the batteries. Two flashes indicates that the unit timed out.
DC panel battery uninterrupted power supply switching circuit
The DC panel battery is commonly utilized in power plants and substations within DC systems. To enhance the safety and reliability of the current system, an uninterrupted power supply switching circuit may be implemented. This circuit includes components such as...
Magnetic Card Reader with PIC12F675
The reader mechanism shown was purchased from All Electronics for $1.50. The unit provides the magnetic head on a spring mechanism along with low level head signal amplifiers and data slicers. Three signal lines coming from the unit provide card...
Training Boxing timer schematic
A timer is being developed for circuit training or boxing training. The timer does not require any external input, except for a reset function. The project can be simplified using a microcontroller, such as the PIC12F635, which is cost-effective at...
Robot Motor Control Schematic
The schematic for controlling the motors is divided into three main sections, each serving a distinct function. The primary components featured in the schematic include the PIC 18F252 microcontroller, the SN754410 motor driver, and 2N2222 transistors. At the top of...
POWER LINE MODEM FOR COMPUTER CONTROL
This circuit employs an 87C57 microcontroller along with several peripherals to convert X-10 power-line carrier-code formats from a personal computer for use with an X-10 power-line interface in a home-control system. Software details can be found in the reference.
The circuit...
NiMH Charger For Up To Six Cells
The circuit is designed for charging NiMH batteries using the MAX712 integrated circuit (IC), which provides all necessary functionalities for controlled charging. The schematic of the charger is centered around IC1, the MAX712 from Maxim, which comes in a standard...
Programmable Zener
The ICL8212 is configured as a programmable zener diode, allowing for the programming of zener voltages ranging from 2 V to 30 V by appropriately selecting R2. The zener voltage is influenced by this selection. Additionally, due to the lack...
Experimental I/O board for microcontrollers
For beginners experiencing similar challenges, a general-purpose I/O board is recommended to minimize prototyping time and maximize space on the breadboard for projects. The construction of this board is straightforward. Basic I/O devices can be soldered onto a general-purpose perforated...
microcontroller How does this power supply circuit work? (MCU + LM317)
The filter consisting of resistors R1, R2, and capacitor C1 integrates the PWM waveform. The purpose of the operational amplifier appears to be that of a non-inverting amplifier, with the gain determined by resistors R6 and R7. However, the need...