long delay timer schematics
Description: This timer is designed to automatically switch off a portable radio after a set period, allowing users to relax without worrying about battery drain. Resistor R1 and capacitor C1 create a long time constant. When switch P2 is momentarily closed, capacitor C1 discharges, causing a near-zero voltage at its positive lead, which is applied to the high-impedance inputs of the four gates of IC1 connected in parallel. The outputs of these gates go high, making battery voltage available at the emitter of transistor Q1. Once P2 is released, C1 begins to charge slowly through R1. When the voltage at the positive lead reaches approximately half the battery voltage, the outputs of the IC gates drop to zero, turning off Q1. This transistor can drive a portable radio receiver or other devices that draw up to 250mA. For devices requiring higher voltage and current, a relay can be connected across the emitter of Q1 and the negative ground. Activating P2 for 1 to 5 seconds initiates the circuit, which will then turn off after about 35 minutes. The time delay can be adjusted by altering the values of R1 and/or C1. Switch P1 can be used to stop the timer if necessary. A 4011 Quad 2 Input NAND Gate is utilized as IC1, although various other CMOS gates or inverter arrays such as 4001, 4002, 4025, 4012, 4023, 4049, and 4069 can also be employed. When using these alternatives, all inputs and outputs must be connected together as depicted in the circuit diagram.
The described timer circuit is a practical solution for managing power consumption in portable radio devices, particularly beneficial for users who may fall asleep while listening. The design employs a simple RC time constant created by R1 and C1, which directly influences the duration before the radio switches off. The choice of a 4011 Quad 2 Input NAND Gate for IC1 is notable, as it allows for the parallel configuration of multiple gates, enhancing the reliability of the circuit's operation.
The momentary switch P2 serves as the activation point, and its design ensures that the circuit remains in a low-power state until engaged. The charging and discharging behavior of C1, in conjunction with R1, establishes a predictable timing mechanism. This feature is crucial for applications where precise timing is necessary, such as in scenarios where users may not be able to manually switch off the device.
Transistor Q1 plays a critical role in driving the load, with its emitter providing a direct connection to the device. The capability to connect a relay expands the circuit’s functionality, enabling it to control devices with higher power requirements. This versatility makes the timer suitable for a wide range of applications beyond just portable radios.
Overall, the circuit's design allows for easy adjustments to the timing interval, making it adaptable to different user needs. The inclusion of P1 for manual interruption of the timer adds an additional layer of control, ensuring that users can override the automatic shut-off feature if desired. The schematic design is straightforward, making it accessible for hobbyists and engineers alike, while also providing a robust solution for energy management in portable electronics.This timer was designed mainly to switch off a portable radio after some time: in this way, one can fall asleep on the sand or on a hammock, resting assured that the receiver will switch off automatically after some time, saving battery costs. R1 and C1 provide a very long time constant. When P2 is momentarily closed, C1 discharges and the near ze ro voltage at its positive lead is applied to the high impedance inputs of the four gates of IC1 wired in parallel. The four paralleled gate outputs of the IC go therefore to the high state and the battery voltage is available at Q1 Emitter.
When P2 is released, C1 starts charging slowly through R1 and when the voltage at its positive lead has reached about half the battery voltage, the IC gate outputs fall to zero, stopping Q1. This transistor can directly drive a portable radio receiver or different devices drawing a current up to about 250mA.
Connecting a Relay across the Emitter of Q1 and negative ground, devices requiring much higher voltage and current operation can be driven through its contacts. Pushing on P2 for 1 to 5 seconds, the circuit starts and then will switch off after about 35 minutes.
This time delay can be varied by changing R1 and/or C1 values. P1 will stop the timer if required. A 4011 Quad 2 Input NAND Gate was used for IC1, but many other CMos gates or inverter arrays can be used in its place, e. g. 4001, 4002, 4025, 4012, 4023, 4049, 4069. With these devices, all inputs must be tied together and also all outputs, as shown in the Circuit diagram.
The described timer circuit is a practical solution for managing power consumption in portable radio devices, particularly beneficial for users who may fall asleep while listening. The design employs a simple RC time constant created by R1 and C1, which directly influences the duration before the radio switches off. The choice of a 4011 Quad 2 Input NAND Gate for IC1 is notable, as it allows for the parallel configuration of multiple gates, enhancing the reliability of the circuit's operation.
The momentary switch P2 serves as the activation point, and its design ensures that the circuit remains in a low-power state until engaged. The charging and discharging behavior of C1, in conjunction with R1, establishes a predictable timing mechanism. This feature is crucial for applications where precise timing is necessary, such as in scenarios where users may not be able to manually switch off the device.
Transistor Q1 plays a critical role in driving the load, with its emitter providing a direct connection to the device. The capability to connect a relay expands the circuit’s functionality, enabling it to control devices with higher power requirements. This versatility makes the timer suitable for a wide range of applications beyond just portable radios.
Overall, the circuit's design allows for easy adjustments to the timing interval, making it adaptable to different user needs. The inclusion of P1 for manual interruption of the timer adds an additional layer of control, ensuring that users can override the automatic shut-off feature if desired. The schematic design is straightforward, making it accessible for hobbyists and engineers alike, while also providing a robust solution for energy management in portable electronics.This timer was designed mainly to switch off a portable radio after some time: in this way, one can fall asleep on the sand or on a hammock, resting assured that the receiver will switch off automatically after some time, saving battery costs. R1 and C1 provide a very long time constant. When P2 is momentarily closed, C1 discharges and the near ze ro voltage at its positive lead is applied to the high impedance inputs of the four gates of IC1 wired in parallel. The four paralleled gate outputs of the IC go therefore to the high state and the battery voltage is available at Q1 Emitter.
When P2 is released, C1 starts charging slowly through R1 and when the voltage at its positive lead has reached about half the battery voltage, the IC gate outputs fall to zero, stopping Q1. This transistor can directly drive a portable radio receiver or different devices drawing a current up to about 250mA.
Connecting a Relay across the Emitter of Q1 and negative ground, devices requiring much higher voltage and current operation can be driven through its contacts. Pushing on P2 for 1 to 5 seconds, the circuit starts and then will switch off after about 35 minutes.
This time delay can be varied by changing R1 and/or C1 values. P1 will stop the timer if required. A 4011 Quad 2 Input NAND Gate was used for IC1, but many other CMos gates or inverter arrays can be used in its place, e. g. 4001, 4002, 4025, 4012, 4023, 4049, 4069. With these devices, all inputs must be tied together and also all outputs, as shown in the Circuit diagram.
Car Headlights Timer Circuit
This device is a simple timer that keeps the headlights of a vehicle on for approximately 1 minute and 30 seconds, allowing access to dark areas without the need to manually switch off the lights. Activating switch P1 initiates the...
Electronic Timer Switch
This electronic timer switch will turn on a light for 100 seconds, turn it off for another 100 seconds, and then turn it on again for 100 seconds after an hour of powering up the circuit. It is a good...
The Time Delay Circuit
The duration for which the circuit remains active is determined by the time required for the stored electrical current to leak back into the circuit, which keeps the transistor and the entire circuit energized. A resistor is present that limits...
Delayed Power supply schematic
I had designed up an oscillator with a Power Output circuit. Problem was when power was applied to the entire circuit, the output of the Oscillator gave a Momentary Spike into the output circuit. Thus Driving it full on for...
Digital Stop Watch and Digital Timer Circuit
A digital stopwatch or digital timer circuit schematic is constructed using the timer IC LM555 and the 4-digit counter IC MM74C926, which is paired with a multiplexed 7-segment LED display.
The digital stopwatch circuit utilizes the LM555 timer IC configured in...
A bedside lamp delay circuit
The circuit includes a CD4 component with a connection of 16 feet for the Vcc terminal, 8 feet for the ground, 12 feet for the reset terminal, 7 feet for the Qt end, and 3 feet for the Q end....
simple delay speaker circuit schematic
This circuit was designed for an audio amplifier project to control the speaker output relay. The primary function of this circuit is to manage the relay that activates the speaker output in the audio amplifier. The circuit introduces a delay...
Automatic sprinkler controller circuit diagram 1
The automatic sprinkler controller circuit consists of a clock timing controller, a monostable flip-flop, a bistable flip-flop, an electronic switch, a self-excited multivibrator, a counter, a solenoid valve control circuit, and a power supply circuit. The power supply circuit includes...
Using the MCU Timers
Although there are significant variations between different implementations of the general-purpose timer in various microcontrollers, many similarities exist in the principles of operation and the structure of the timer subsystem. The central element of the timer subsystem is a counter,...