simple emergency led light circuit
#LED
#emergency light
#LM317
#voltage regulator
#battery backup
#automatic switching
#12V converter
#220V AC
#white LEDs
#brownout protection
Description: This emergency LED light is simple, inexpensive, and easy to build. The circuit connects to the battery, activating when the main power source is unavailable, such as during brownouts. White LEDs turn on automatically. Initially, the output voltage from a 220V to 12V converter is fed to the input of an LM317 regulator. This voltage is then regulated to 7.37V using a combination of a 240-ohm resistor and a 1.2K-ohm resistor (as determined by the LM317 Calculator). At this point, the battery is in charging mode, and the transistor Q1 is off. The LED serves two purposes: it indicates that the battery is charging and ensures that Q1 remains off. During voltage drops, transistor Q1 turns on, supplying current to 16 white LEDs at approximately 20 mA each. A fully charged battery (6V/4.5Ah) can last up to 14 hours.
The emergency LED light circuit is designed to operate under conditions where the main power supply is disrupted. The circuit begins with a 220V AC input, which is transformed down to 12V DC using a suitable transformer and rectifier configuration. This 12V output is then fed into an LM317 voltage regulator, which is configured to output a stable 7.37V. The LM317 requires two resistors for voltage setting: a fixed 240-ohm resistor and a variable resistor (typically 1.2K ohms) to fine-tune the output voltage.
When the main power supply is available, the LED indicator remains off, and the battery is charged. The circuit ensures that the transistor Q1 remains in the off state during this charging phase, preventing any current from flowing to the LED array. The LED indicator serves a dual purpose: it illuminates when the battery is charging and confirms that Q1 is not conducting.
Upon detection of a voltage drop, such as during a brownout, the transistor Q1 is activated, allowing current to flow to the 16 white LEDs connected in parallel. Each LED draws approximately 20 mA, resulting in a total current draw of about 320 mA when all LEDs are illuminated. The circuit is designed to utilize a 6V, 4.5Ah rechargeable battery, which can sustain the LED operation for up to 14 hours when fully charged.
This emergency LED light circuit is effective for providing illumination during power outages, ensuring safety and visibility. The simplicity of the design and the availability of components make it an excellent project for both novice and experienced electronics enthusiasts.This emergency LED light is simple, inexpensive and easy to build. The circuit to the battery and when the main source is not available, such as brownouts, white LEDs turns on automatically. Initially, the output voltage from 220V to 12V converter is fed to the input of LM317 regulator. Then, this voltage is regulated to 7. 37V with 240 ohms and th e combination of the resistance of 1. 2K (see LM317 Calculator). At this time, the battery is in charging mode and the transistor Q1 is off. LED serves two purposes, one is mainly to give us an idea of the battery is charging and the other is to ensure that Q1 is off. During voltage drops, the transistor Q1 is on and supplies the current to 16 white LED of about 20 mA each, so a fully charged battery (6V/4.
5Ah) may last up to 14 hours.
The emergency LED light circuit is designed to operate under conditions where the main power supply is disrupted. The circuit begins with a 220V AC input, which is transformed down to 12V DC using a suitable transformer and rectifier configuration. This 12V output is then fed into an LM317 voltage regulator, which is configured to output a stable 7.37V. The LM317 requires two resistors for voltage setting: a fixed 240-ohm resistor and a variable resistor (typically 1.2K ohms) to fine-tune the output voltage.
When the main power supply is available, the LED indicator remains off, and the battery is charged. The circuit ensures that the transistor Q1 remains in the off state during this charging phase, preventing any current from flowing to the LED array. The LED indicator serves a dual purpose: it illuminates when the battery is charging and confirms that Q1 is not conducting.
Upon detection of a voltage drop, such as during a brownout, the transistor Q1 is activated, allowing current to flow to the 16 white LEDs connected in parallel. Each LED draws approximately 20 mA, resulting in a total current draw of about 320 mA when all LEDs are illuminated. The circuit is designed to utilize a 6V, 4.5Ah rechargeable battery, which can sustain the LED operation for up to 14 hours when fully charged.
This emergency LED light circuit is effective for providing illumination during power outages, ensuring safety and visibility. The simplicity of the design and the availability of components make it an excellent project for both novice and experienced electronics enthusiasts.This emergency LED light is simple, inexpensive and easy to build. The circuit to the battery and when the main source is not available, such as brownouts, white LEDs turns on automatically. Initially, the output voltage from 220V to 12V converter is fed to the input of LM317 regulator. Then, this voltage is regulated to 7. 37V with 240 ohms and th e combination of the resistance of 1. 2K (see LM317 Calculator). At this time, the battery is in charging mode and the transistor Q1 is off. LED serves two purposes, one is mainly to give us an idea of the battery is charging and the other is to ensure that Q1 is off. During voltage drops, the transistor Q1 is on and supplies the current to 16 white LED of about 20 mA each, so a fully charged battery (6V/4.
5Ah) may last up to 14 hours.
Simple Twi-light using white LEDs
This sunlight-controlled lamp utilizes a light-dependent resistor (LDR) as the sunlight sensor and comprises a total of 25 high-brightness white LEDs. Each row of LEDs is connected in series with separate resistors. The operation of the circuit is straightforward. During...
LED Counter with IC 4017
The circuit presented this month is a basic configuration of the very versatile 4017 IC Chip. In the most common use of the IC, it will turn on 10 separate outputs sequentially. Typically, the circuit is used to turn on...
LED Traffic Lights for Games with 555
The LED traffic Light circuit controls 6 LEDs (red, yellow and green) for both north/south directions and east/west directions. The timing sequence is generated using a CMOS 4017 decade counter and a 555 timer. Counter outputs 1 through 4 are...
Light Related
Watch the video below to gain a better understanding of how a light-emitting diode (LED) functions. An LED is recognized as one of the most effective optoelectronic devices available. This device emits a relatively narrow bandwidth of visible or invisible...
Key Illuminator Circuit
Used as a 10-second momentary illuminator, this circuit can be useful in other applications as well. Pressing SI charges CI, which holds Q1 on and keeps the LED lit for about 10 seconds.
The circuit described functions as a momentary illuminator,...
LED Chaser
I don't know why, but people like blinking lights. You see LED chasers everywhere, in TV shows (Knight Rider), movies, and store windows. This schematic is my version of a simple 10 LED chaser. There is no 555 timer used...
Puff to OFF LED circuit
This circuit features an LED that can be turned off with a puff of air. A condenser microphone (M1) detects the puff. When the push button switch S1 is activated, transistors Q2 and Q3, configured as a latching pair, are...
LED Flashing circuits
This is a very simple project using a printed circuit board and 8 components. It will flash an ordinary 3mm or 5mm (1/8" or 1/4") LED at a rate of about one flash per second. This circuit works on the...
How to Make a Simple Reverse Forward LED Light Chaser Circuit Using IC 4017
An LED light chaser circuit is an electronic configuration designed to illuminate a group of LEDs in a predetermined sequence. A commonly used integrated circuit (IC) for creating this type of LED sequencer circuit is the 4017. This IC functions...