10 Dancing LEDs
#LED
#microphone
#audio amplifier
#peak detector
#ring decade counter
#constant current source
#switching transistor
#9V supply
#dancing LEDs
Description: The basic circuit illuminates up to ten LEDs in sequence, following the rhythm of music or speech picked up by a small microphone. The expanded version can drive up to ten strips, formed by up to five LEDs each, at 9V supply. IC1A amplifies about 100 times the audio signal picked up by the microphone and drives IC1B acting as a peak-voltage detector. Its output peaks are synchronous with the peaks of the input signal and clock IC2, a ring decade counter capable of driving up to ten LEDs in sequence. An additional circuit allows the driving of up to ten strips, made up of five LEDs each (max.), at 9V supply. It is formed by a 10mA constant current source (Q1 & Q2) common to all LED strips and by a switching transistor (Q3), driving a strip obtained from 2 to 5 series-connected LEDs. Therefore, one transistor and its Base resistor are required to drive each of the strips used.
The circuit operates by utilizing audio signals captured from the environment via a microphone, which serves as the primary input. The microphone's output is first amplified by operational amplifier IC1A, providing a gain of approximately 100. This amplified signal is then fed into IC1B, which functions as a peak-voltage detector. The output from IC1B generates a pulse corresponding to the peaks of the audio signal, which is critical for synchronizing the LED illumination with the rhythm of the music or speech.
The output pulses from IC1B are utilized to clock IC2, a ring decade counter. This counter is capable of sequentially driving up to ten outputs, each connected to an LED. The result is a visually dynamic display where the LEDs illuminate in a sequence that corresponds to the rhythm detected in the audio signal.
For the expanded version of the circuit, the design accommodates the driving of LED strips. Each strip can consist of up to five LEDs, and the entire setup operates at a 9V power supply. The constant current source, constructed from transistors Q1 and Q2, ensures that each LED strip receives a stable 10mA current, which is crucial for consistent brightness across the LED strips.
Transistor Q3 acts as a switch, allowing the control of individual LED strips. Each strip requires its own transistor and associated base resistor to ensure proper operation. The configuration of series-connected LEDs within each strip allows for flexibility in design, as the number of LEDs can be adjusted based on the desired brightness and voltage drop across the LEDs.
Overall, this circuit exemplifies a practical application of audio signal processing in a visual display context, effectively combining sound detection with LED control to create an engaging user experience.The basic circuit illuminates up to ten LEDs in sequence, following the rhythm of music or speech picked-up by a small microphone. The expanded version can drive up to ten strips, formed by up to five LEDs each, at 9V supply. IC1A amplifies about 100 times the audio signal picked-up by the microphone and drives IC1B acting as peak-voltage detector.
Its output peaks are synchronous with the peaks of the input signal and clock IC2, a ring decade counter capable of driving up to ten LEDs in sequence. An additional circuit allows the driving of up to ten strips, made up by five LEDs each (max.), at 9V supply.
It is formed by a 10mA constant current source (Q1 & Q2) common to all LED strips and by a switching transistor (Q3), driving a strip obtained from 2 to 5 series-connected LEDs. Therefore one transistor and its Base resistor are required to drive each of the strips used.
The circuit operates by utilizing audio signals captured from the environment via a microphone, which serves as the primary input. The microphone's output is first amplified by operational amplifier IC1A, providing a gain of approximately 100. This amplified signal is then fed into IC1B, which functions as a peak-voltage detector. The output from IC1B generates a pulse corresponding to the peaks of the audio signal, which is critical for synchronizing the LED illumination with the rhythm of the music or speech.
The output pulses from IC1B are utilized to clock IC2, a ring decade counter. This counter is capable of sequentially driving up to ten outputs, each connected to an LED. The result is a visually dynamic display where the LEDs illuminate in a sequence that corresponds to the rhythm detected in the audio signal.
For the expanded version of the circuit, the design accommodates the driving of LED strips. Each strip can consist of up to five LEDs, and the entire setup operates at a 9V power supply. The constant current source, constructed from transistors Q1 and Q2, ensures that each LED strip receives a stable 10mA current, which is crucial for consistent brightness across the LED strips.
Transistor Q3 acts as a switch, allowing the control of individual LED strips. Each strip requires its own transistor and associated base resistor to ensure proper operation. The configuration of series-connected LEDs within each strip allows for flexibility in design, as the number of LEDs can be adjusted based on the desired brightness and voltage drop across the LEDs.
Overall, this circuit exemplifies a practical application of audio signal processing in a visual display context, effectively combining sound detection with LED control to create an engaging user experience.The basic circuit illuminates up to ten LEDs in sequence, following the rhythm of music or speech picked-up by a small microphone. The expanded version can drive up to ten strips, formed by up to five LEDs each, at 9V supply. IC1A amplifies about 100 times the audio signal picked-up by the microphone and drives IC1B acting as peak-voltage detector.
Its output peaks are synchronous with the peaks of the input signal and clock IC2, a ring decade counter capable of driving up to ten LEDs in sequence. An additional circuit allows the driving of up to ten strips, made up by five LEDs each (max.), at 9V supply.
It is formed by a 10mA constant current source (Q1 & Q2) common to all LED strips and by a switching transistor (Q3), driving a strip obtained from 2 to 5 series-connected LEDs. Therefore one transistor and its Base resistor are required to drive each of the strips used.
200 Watt audio power amplifier
Here I propose a project of an AB class power amplifier, at its simplest, assembled with common components (not very expensive), based on traditional diagrams: a symmetrical differential input stage, a cascode stage driver, and a MOSFET output stage. The...
Exit Sign With Battery Protection
This circuit replaces two white Luxeon 1W Star LEDs for the inverter and fluorescent tube in a standard battery-powered illuminated exit sign, commonly found in commercial buildings. Although the Luxeon LEDs produce less light output than a typical small fluorescent...
LED Traffic Lights for Games with 555
The LED traffic Light circuit controls 6 LEDs (red, yellow and green) for both north/south directions and east/west directions. The timing sequence is generated using a CMOS 4017 decade counter and a 555 timer. Counter outputs 1 through 4 are...
Electronic dice
Six LEDs are arranged to create a display that mimics the dots on a dice. When the push button input (PBI) is pressed, the display is turned off, and the oscillator (IC1 a, b, c) drives IC2 at approximately 1...
LED Bike Light Circuit Project
On a mountain bike, a common issue with traditional flashing LED lights from stores is the frequent problem of flat batteries and lights detaching. As an electronics student, a better solution was sought. A front wheel with a built-in dynamo...
LED Color Fade Effect circuit diagram
This circuit creates an LED color fade effect. As indicated by the name, the light intensity of the LEDs in this circuit transitions from high intensity to low intensity and eventually turns off. A 30 µF capacitor and a 100...
White LED Head Lamp
This is a practical white LED head mount lamp (flashlight). Recently many white LED flashlights appear on the market. However, most flashlights require three cells because they are regulating output current with only series resistor. The odd number of cells...
Conference MIC
If the audio output is connected to equipment with a balanced input circuit that has a separate ground connection, the ground connects to OUTPUT terminal #1. The PZ-2LA can be powered by an external AC or DC source ranging from...
Audio power amplifier
Output-clamp diodes are essential due to the inductive nature of loudspeakers. Output LR isolation is employed as audio amplifiers are typically designed to manage load capacitance of up to 2 µF. Large supply-bypass capacitors placed near the integrated circuit (IC)...