Up/Down Timer For A Power Antenna
#timer
#power antenna
#vehicle
#audio system
#control circuit
#automotive electronics
#car stereo
#custom installation
Description: This up/down timer was designed to control a power antenna on a late-model vehicle. Normally, this vehicle uses a body computer to control the antenna. However, the owner intended to install a high-powered audio stereo system. The original stereo system was integrated with the body computer, necessitating a separate antenna controller for the aftermarket sound system. Additionally, the installed power antenna lacked internal limit switches, which led to the requirement for a timed control circuit.
The circuit operates as follows: when the radio antenna control output is off (i.e., the radio is off), relay RLYC remains off, which in turn keeps relay RLYA and the motor off. Conversely, when the radio is turned on, the radio antenna control output line switches to +12V. This action causes RLYC to close its contacts and power the circuit. Consequently, capacitor C2 (330µF) charges rapidly through diode D4, while transistor Q4 is biased on via diode D5 and resistor R5, ensuring that Q3 and relay RLYB remain off. Simultaneously, Q2 is activated, powering relay RLYA and driving the motor to extend the antenna. During this process, capacitor C1 charges through resistor R2. Once the voltage across C1 reaches +8.1V, transistor Q1 is activated via ZD1, turning off Q2 and consequently deactivating the relay, which initiates the "up" timeout. The specified values for C1, R2, and ZD1 yield an "up" duration of approximately 6 seconds, sufficient to fully extend the antenna. Diode D1 discharges capacitor C1 through resistor R1 when the +12V supply is removed.
When the radio is switched off (or a CD is inserted into the stereo unit), the radio antenna control output returns to 0V. This action results in Q4 turning off, allowing Q3 to turn on due to the stored charge in C2. Q3 and relay RLYB activate for about six seconds, during which C2 discharges through resistor R4, reversing power to the motor and retracting the antenna. Diodes D4 and D5 are included to prevent C2 from discharging back through the circuitry connected to Q1 and Q2.
This circuit design effectively addresses the need for a reliable power antenna control system in vehicles where the original body computer integration is bypassed due to aftermarket audio system installations. The timed control mechanism ensures proper operation without the need for limit switches, providing a functional and efficient solution for antenna management. The use of capacitors, resistors, and transistors allows for precise control over the antenna's movement, ensuring that the system operates seamlessly in conjunction with the vehicle's audio system.This up/down timer was designed to control a power antenna on a late-model vehicle. Normally, this vehicle uses a body computer to control the antenna. However, the person who owned the vehicle wanted to install his own high-powered audio stereo system. The original stereo system was tied in with the body computer and this meant that a separate an tenna controller was required for the after-market sound system. Also, the power antenna fitted did not have limit switches inside, hence the need for a timed control circuit. Here`s how the circuit works. first, assume that the radio antenna control output is not switched on - ie, the radio is switched off.
In that case, relay RLYC will be off and so relay RLYA will also be off, as is the motor. Conversely, when the radio is switched on, the radio antenna control output line switches to +12V. And when that happens, RLYC closes its contacts and applies power to the circuit. As a result, C2 (330OF) quickly charges via D4, while Q4 is biased on via D5 and R5. This ensures that Q3 and relay RLYB remain off. At the same time, Q2 is is turned on, thus turning on RLYA and applying power to the motor. This drives the antenna in the up direction. During this time, C1 charges via R2. When the voltage across the capacitor reaches +8. 1V, Q1 turns on via ZD1 and so Q2 turns off and switches off the relay - ie, this gives the "up" timeout. Using the values shown for C1, R2 and ZD1 gives an "up" duration of approximately 6 seconds - long enough to fully extend the antenna.
D1 discharges C1 (via resistor R1) when the +12V supply is later removed. When the radio is switched off (or a CD placed into the stereo unit), the radio antenna control output switches back to 0V. This does several things: first, it turns Q4 off and this allows Q3 to turn on due to the stored charge in C2.
Q3 and RLYB now turn on for about six seconds - ie, while C2 discharges via R4 - and this switches power to the motor in the opposite direction to drive the antenna down. Diodes D4 and D5 are there to prevent C2 from discharging back via the circuitry around on Q1 and Q2.
The circuit operates as follows: when the radio antenna control output is off (i.e., the radio is off), relay RLYC remains off, which in turn keeps relay RLYA and the motor off. Conversely, when the radio is turned on, the radio antenna control output line switches to +12V. This action causes RLYC to close its contacts and power the circuit. Consequently, capacitor C2 (330µF) charges rapidly through diode D4, while transistor Q4 is biased on via diode D5 and resistor R5, ensuring that Q3 and relay RLYB remain off. Simultaneously, Q2 is activated, powering relay RLYA and driving the motor to extend the antenna. During this process, capacitor C1 charges through resistor R2. Once the voltage across C1 reaches +8.1V, transistor Q1 is activated via ZD1, turning off Q2 and consequently deactivating the relay, which initiates the "up" timeout. The specified values for C1, R2, and ZD1 yield an "up" duration of approximately 6 seconds, sufficient to fully extend the antenna. Diode D1 discharges capacitor C1 through resistor R1 when the +12V supply is removed.
When the radio is switched off (or a CD is inserted into the stereo unit), the radio antenna control output returns to 0V. This action results in Q4 turning off, allowing Q3 to turn on due to the stored charge in C2. Q3 and relay RLYB activate for about six seconds, during which C2 discharges through resistor R4, reversing power to the motor and retracting the antenna. Diodes D4 and D5 are included to prevent C2 from discharging back through the circuitry connected to Q1 and Q2.
This circuit design effectively addresses the need for a reliable power antenna control system in vehicles where the original body computer integration is bypassed due to aftermarket audio system installations. The timed control mechanism ensures proper operation without the need for limit switches, providing a functional and efficient solution for antenna management. The use of capacitors, resistors, and transistors allows for precise control over the antenna's movement, ensuring that the system operates seamlessly in conjunction with the vehicle's audio system.This up/down timer was designed to control a power antenna on a late-model vehicle. Normally, this vehicle uses a body computer to control the antenna. However, the person who owned the vehicle wanted to install his own high-powered audio stereo system. The original stereo system was tied in with the body computer and this meant that a separate an tenna controller was required for the after-market sound system. Also, the power antenna fitted did not have limit switches inside, hence the need for a timed control circuit. Here`s how the circuit works. first, assume that the radio antenna control output is not switched on - ie, the radio is switched off.
In that case, relay RLYC will be off and so relay RLYA will also be off, as is the motor. Conversely, when the radio is switched on, the radio antenna control output line switches to +12V. And when that happens, RLYC closes its contacts and applies power to the circuit. As a result, C2 (330OF) quickly charges via D4, while Q4 is biased on via D5 and R5. This ensures that Q3 and relay RLYB remain off. At the same time, Q2 is is turned on, thus turning on RLYA and applying power to the motor. This drives the antenna in the up direction. During this time, C1 charges via R2. When the voltage across the capacitor reaches +8. 1V, Q1 turns on via ZD1 and so Q2 turns off and switches off the relay - ie, this gives the "up" timeout. Using the values shown for C1, R2 and ZD1 gives an "up" duration of approximately 6 seconds - long enough to fully extend the antenna.
D1 discharges C1 (via resistor R1) when the +12V supply is later removed. When the radio is switched off (or a CD placed into the stereo unit), the radio antenna control output switches back to 0V. This does several things: first, it turns Q4 off and this allows Q3 to turn on due to the stored charge in C2.
Q3 and RLYB now turn on for about six seconds - ie, while C2 discharges via R4 - and this switches power to the motor in the opposite direction to drive the antenna down. Diodes D4 and D5 are there to prevent C2 from discharging back via the circuitry around on Q1 and Q2.
5 to 30 Minute Timer
A switched timer for intervals of 5 to 30 minutes incremented in 5 minute steps. Simple to build, simple to make, nothing too complicated here. However, you must use the CMOS type 555 timer designated the 7555; a normal 555...
Self Retriggering Timed Generator Circuit
When power is first applied to the circuit, capacitor C2 begins to charge through LED1, resistor R3, and resistor R4. When the voltage across C2 reaches the input trigger level of operational amplifier U1, the output at pin 6 of...
Long Delay Timer Circuit
This timer is designed primarily to turn off a portable radio after a set duration. This feature allows users to relax on the beach or in a hammock, confident that the device will automatically power down after a specified period,...
1 Hour Timer
Speaker relay delay controlling circuit for audio amplifier
The speaker relay delay control circuit is designed to protect audio amplifiers and speakers from potential damage caused by inrush current or transient signals during power-up or power-down sequences. This circuit typically employs...
Jogging Timers
This circuit was developed in response to requests from visitors of this website for a timer that can emit a beep after one, two, three minutes, and so on, for jogging purposes. As illustrated in the circuit diagram, SW1 is...
A Timer That Re-Triggers At Regular Intervals
This circuit features an adjustable output timer that can re-trigger at regular intervals. The output duration can range from a fraction of a second to half an hour or more, and it can be configured to recur at intervals from...
R/C Timer-Switch for Radio Control Applications
The project originated from a request by Tony Bowler, a member of the Long Eaton Club, who sought assistance in converting a "Golden Oldie" model to electric free-flight. He selected Vic Smeed's "Debutante" to be powered by seven AE size...
Timer Circuit with optocoupler
A small circuit that can find a lot of applications for measuring time. It has the capability to inform with a sound signal from the BZ1. At the same time, there exists the possibility to drive an external circuit via...
tan timer schematics
This timer is intended for individuals seeking to achieve a tan while minimizing excessive exposure to sunlight. A rotary switch adjusts the timer based on six categorized photo-types. A photoresistor modifies the preset time value in relation to sunlight brightness....