Arduino IR Transmitter & Receiver w/ LEDs Flickering Issue (Whats wrong with this circuit?)
Description: An Arduino Uno is connected to two infrared (IR) transmitters and their respective receivers. When one of the receivers detects a beam break, a strand of LEDs displays a pattern. While this setup functions correctly in principle, an issue arises when the IR transmitters and receivers are connected to the Arduino, causing the LEDs to flicker with random colors. Initially, when the IR transmitters and receivers are disconnected, the system operates without issues. However, once the receivers are connected, flickering begins after approximately 8 seconds. This flickering persists even after disconnecting the IR receivers, although at a reduced frequency. The Arduino is powered via USB, and the LED strand is powered from an external 12V power supply. The user has not found a specific diagram for the LED strand. The IRremote library is used to control the IR transmitters, and the strandtest example from the Adafruit WS2801 LED library is currently being tested. Notably, another similar strand of LEDs does not exhibit flickering regardless of the IR connections. A potential solution considered is to use an external power supply for the IR components to prevent them from being connected to the Arduino. Clarification is sought regarding the appropriate specifications for such a power supply in terms of voltage and amperage output.
The circuit described involves an Arduino Uno interfacing with two IR transmitters and receivers, which are used for detecting interruptions in an IR beam. The LEDs are controlled to display specific patterns upon detection of a beam break. The flickering issue observed suggests a possible grounding or power supply interference problem, which can occur when multiple components share the same power source.
To address the flickering, it is advisable to isolate the power supply for the IR components from the Arduino. This can be achieved by using a dedicated external power supply for the IR transmitters and receivers. The voltage requirement for the IR components typically matches that of the Arduino, which is 5V. However, it is essential to verify the specifications of the IR transmitters and receivers to confirm their voltage requirements.
In determining the amperage output for the external power supply, the total current draw of the IR components should be calculated. This can be done by checking the datasheets for the specific IR transmitters and receivers to find their current consumption. Adding a margin of safety (typically 20-30%) to the total current requirement will ensure that the power supply can handle any additional load or inrush current when the components are activated.
Additionally, it is recommended to implement proper decoupling capacitors near the power pins of the IR components to filter out any noise that may contribute to the flickering. Using capacitors with values ranging from 0.1 µF to 10 µF in parallel can help stabilize the power supply.
In conclusion, isolating the IR components with a dedicated power supply, verifying their voltage and current specifications, and incorporating decoupling capacitors can significantly improve the performance of the circuit and eliminate the flickering issue experienced with the LEDs.An Arduino Uno connected to two IR transmitters and respective receivers. Basically, when one of the receivers detects a beam break, I have a strand of LEDs display a pattern. This all works in principle, but the problem is that when the IR transmitters and receivers are connected to the Arduino, the LEDs flicker with random colors.
Here`sa video of exactly what`s happening. At first, the IR transmitters and receivers are disconnected and everything is fine, then I connect the IR receivers and the flickering begins at around 8 seconds. . The flickering will continue even when I disconnect the IR receiver, albeit at a reduced rate. In the above diagram, the Arduino is powered via USB (I tried with a 12V power supply too), and the LED strand is powered from an external 12V power supply (I couldn`t find a diagram for an LED strand).
If it matters, I should mention that I`m using the IRremote library to control the IR transmitters ( ) and the strandtest example from the Adafruit WS2801 LED library ( ) to test everything right now. The strange thing is that I also have another strand of similar LEDs ( ) and they do not experience the flickering regardless of if the IR transmitters and receivers are connected or not.
So the only thing I can think of is to use an external power supply for the IR so as it avoid connecting them to the Arduino. Is that a valid solution If so, how do I got about determining what power supply I would need (in terms of voltage and amperage output)
The circuit described involves an Arduino Uno interfacing with two IR transmitters and receivers, which are used for detecting interruptions in an IR beam. The LEDs are controlled to display specific patterns upon detection of a beam break. The flickering issue observed suggests a possible grounding or power supply interference problem, which can occur when multiple components share the same power source.
To address the flickering, it is advisable to isolate the power supply for the IR components from the Arduino. This can be achieved by using a dedicated external power supply for the IR transmitters and receivers. The voltage requirement for the IR components typically matches that of the Arduino, which is 5V. However, it is essential to verify the specifications of the IR transmitters and receivers to confirm their voltage requirements.
In determining the amperage output for the external power supply, the total current draw of the IR components should be calculated. This can be done by checking the datasheets for the specific IR transmitters and receivers to find their current consumption. Adding a margin of safety (typically 20-30%) to the total current requirement will ensure that the power supply can handle any additional load or inrush current when the components are activated.
Additionally, it is recommended to implement proper decoupling capacitors near the power pins of the IR components to filter out any noise that may contribute to the flickering. Using capacitors with values ranging from 0.1 µF to 10 µF in parallel can help stabilize the power supply.
In conclusion, isolating the IR components with a dedicated power supply, verifying their voltage and current specifications, and incorporating decoupling capacitors can significantly improve the performance of the circuit and eliminate the flickering issue experienced with the LEDs.An Arduino Uno connected to two IR transmitters and respective receivers. Basically, when one of the receivers detects a beam break, I have a strand of LEDs display a pattern. This all works in principle, but the problem is that when the IR transmitters and receivers are connected to the Arduino, the LEDs flicker with random colors.
Here`sa video of exactly what`s happening. At first, the IR transmitters and receivers are disconnected and everything is fine, then I connect the IR receivers and the flickering begins at around 8 seconds. . The flickering will continue even when I disconnect the IR receiver, albeit at a reduced rate. In the above diagram, the Arduino is powered via USB (I tried with a 12V power supply too), and the LED strand is powered from an external 12V power supply (I couldn`t find a diagram for an LED strand).
If it matters, I should mention that I`m using the IRremote library to control the IR transmitters ( ) and the strandtest example from the Adafruit WS2801 LED library ( ) to test everything right now. The strange thing is that I also have another strand of similar LEDs ( ) and they do not experience the flickering regardless of if the IR transmitters and receivers are connected or not.
So the only thing I can think of is to use an external power supply for the IR so as it avoid connecting them to the Arduino. Is that a valid solution If so, how do I got about determining what power supply I would need (in terms of voltage and amperage output)
long range ir transmitter
Most IR remotes function effectively within a range of 5 meters. Designing an IR transmitter for dependable operation over a longer distance, such as 10 meters, increases circuit complexity. To achieve this doubled range, the transmitted power must be increased...
arduino How can I display a scoreboard on stage for a play
A scoreboard is located in the center of the room, which will be controlled from backstage. The scoreboard features two individual 3-digit numbers. Whenever the score changes, a sound will be emitted. The simplest, most efficient, and cost-effective solution identified...
IR Headset Circuit with headphone Transmitter and Receiver diagram
This document outlines a simple infrared (IR) headphone circuit designed for listening to television or radio without disturbing others. The IR headset is a preferable option for beginners compared to FM headsets due to its desirable sound quality that does...
Arduino Ping
The Ping is an ultrasonic range finder from Parallax. It detects the distance of the closest object in front of the sensor (from 2 cm up to 3 meters). It operates by emitting a burst of ultrasound and listening for...
Glove circuit that lights up with a hand shake
The task involved testing the capacitive properties of food by connecting various edibles to an Arduino. This project, known as BeetBox, was developed by Scott Garner, a student at NYU-ITP, who designed an innovative musical instrument that uses beets as...
Augmenting Plant Behavior Through Robotics using Arduino
The PhytoBot is a semi-intelligent plant that reacts to external stimuli, specifically light intensity and light location, mimicking the behavior of a phototropic plant. It is designed as an interactive artwork intended for prolonged operation. The motivation behind this design...
photoresistors servo and arduino
The movement of the servo is determined by the output values of the photoresistors. The impedance of these sensors changes with the amount of light incident upon them. The servo's position shifts towards the sensor that detects less light. There...
Embedded Development on OSX
Fixed some issues with the Benito Arduino programmer and upgraded it to the latest version of the LUFA library. There was a mismatch between the INF file and the library-supplied descriptors. Apologies to the two XP users. As this is...
get on the blinkm bus with a blinkm cylon
BlinkMs are entertaining devices that function as small network components, each assigned a unique address on an I2C network. The potential of BlinkMs is particularly evident in their ability to simplify the control of multiple RGB LEDs. For a demonstration...