Wireless Coupled Scanning Voltmeter (ATMega8)
#wireless
#voltmeter
#ATMega8
#RF link
#measurement
#battery operated
#scanning
#10 bit
#Minimum Mass
Description: A 10 bit scanning voltmeter with a Minimum Mass Wireless Coupler, based on the ATMega8. Range to the Minimum Mass Base Unit is 10 to 15 cm. If the voltmeter is battery operated, it can be floated from ground. This project is very simple physically, intended to demonstrate how easily the Minimum Mass RF Link can be added to a project. The circuit shown does not have a lot of the nice things that I would usually include in an instrument, such as the ability to handle out-of-range input signals without the circuit suffering damage. Therefore, it is suggested that if this is built as a stand-alone instrument, protection circuitry be added to the inputs. The basic Minimum Mass Wireless Coupler technology is described, and links to other projects on this site that use the Minimum Mass Wireless Coupler are located on the web page, Minimum Mass Wireless Coupler.
The power supply is the reference voltage in this case, and the binary-to-decimal conversion assumes that the reference voltage is +5 volts, so it is suggested that an adjustable regulator be used to obtain a precise +5 volts. Three alkaline cells (for example) could be used in series, but the calibration would be way off. Schematic of the 4 channel scanning voltmeter. The layout isn't critical. The 33 uH choke is used to reduce noise from the controller's VCC pin on the analog reference voltage.
The A/D converter setup and binary-to-decimal conversion routines were taken from the Low Cost Telemetry Device project on this site. The firmware was created by taking the Low Cost Telemetry Device firmware, removing the unneeded code, and adding calls to the Minimum Mass Wireless Coupler drivers instead of to the USART routines.
This circuit design incorporates a 10-bit analog-to-digital converter (ADC) based on the ATMega8 microcontroller, which serves as the core of the scanning voltmeter. The ADC is capable of converting input voltages into digital values, with a range determined by the reference voltage, which is typically set to +5V. To ensure accuracy in readings, an adjustable voltage regulator is recommended for generating the reference voltage, especially if using battery power.
The scanning voltmeter is designed to operate wirelessly, utilizing a Minimum Mass Wireless Coupler, allowing communication with a base unit located within a range of 10 to 15 cm. This feature enhances the versatility of the voltmeter, enabling it to be used in various applications without the constraints of wired connections. The circuit is intended to be simple and straightforward, making it accessible for demonstration purposes and educational projects.
In terms of circuit protection, it is essential to incorporate additional circuitry to safeguard the inputs from out-of-range signals, which could potentially damage the ADC. This may include clamping diodes or series resistors to limit the input voltage levels.
The schematic includes a 33 µH choke placed on the VCC pin of the microcontroller to filter out noise from the power supply, which could affect the accuracy of the analog reference voltage. The layout of the circuit is not critical, allowing for flexibility in design and implementation.
The firmware for the voltmeter is adapted from an existing Low Cost Telemetry Device project. It has been streamlined by removing unnecessary code and incorporating functions specific to the Minimum Mass Wireless Coupler, enabling efficient data transmission without reliance on USART communication. This optimization is vital for enhancing the performance of the scanning voltmeter in wireless applications.A 10 bit scanning voltmeter with a Minimum Mass Wireless Coupler, based on the ATMega8.Range to the Minimum Mass Base Unit is 10 to 15 cm. If the voltmeter is battery operated, it can be floated from ground. This project is very simple physically, intended to demonstrate how easily the Minimum Mass RF Link can be added to a project.
The circuit shown does not have a lot if the nice things that I would usually include in an instrument, such as the ability to handle out-of-range input signals without the circuit suffering damage. Therefore, I suggest that if you build this as a stand-alone instrument, that you add protection crcuitry to the inputs.
The basic Minimum Mass Wireless Coupler technology is described and links to other projects on this site that use the Minimum Mass Wireless Coupler are located on the web page, Minimum Mass Wireless Coupler. The power suuply is the reference voltage in this case, and the binary-to-decimal conversion assumes that the refernce voltage is +5 volts, so I sugges that an adjustable regulator be used to obtain a precise +5 volts. You could use three alkaline cells (for example) in series, but the calibration would be way off. Schematic of the 4 channel scanning voltmeter. The layout isn't critical. The 33 uH choke is reduce noise from the controller's VCC pin on the analog reference voltage. The A/D converter setup and binary-to-decmial conversion routines were taken from the Low Cost Telemetry Device project on this site.
The firmware was created by taking the Low Cost Telemetry Device firmware, removing the un-needed code, and adding calls to the Minimum Mass Wireless Coupler drivers instead of to the USART routines.
The power supply is the reference voltage in this case, and the binary-to-decimal conversion assumes that the reference voltage is +5 volts, so it is suggested that an adjustable regulator be used to obtain a precise +5 volts. Three alkaline cells (for example) could be used in series, but the calibration would be way off. Schematic of the 4 channel scanning voltmeter. The layout isn't critical. The 33 uH choke is used to reduce noise from the controller's VCC pin on the analog reference voltage.
The A/D converter setup and binary-to-decimal conversion routines were taken from the Low Cost Telemetry Device project on this site. The firmware was created by taking the Low Cost Telemetry Device firmware, removing the unneeded code, and adding calls to the Minimum Mass Wireless Coupler drivers instead of to the USART routines.
This circuit design incorporates a 10-bit analog-to-digital converter (ADC) based on the ATMega8 microcontroller, which serves as the core of the scanning voltmeter. The ADC is capable of converting input voltages into digital values, with a range determined by the reference voltage, which is typically set to +5V. To ensure accuracy in readings, an adjustable voltage regulator is recommended for generating the reference voltage, especially if using battery power.
The scanning voltmeter is designed to operate wirelessly, utilizing a Minimum Mass Wireless Coupler, allowing communication with a base unit located within a range of 10 to 15 cm. This feature enhances the versatility of the voltmeter, enabling it to be used in various applications without the constraints of wired connections. The circuit is intended to be simple and straightforward, making it accessible for demonstration purposes and educational projects.
In terms of circuit protection, it is essential to incorporate additional circuitry to safeguard the inputs from out-of-range signals, which could potentially damage the ADC. This may include clamping diodes or series resistors to limit the input voltage levels.
The schematic includes a 33 µH choke placed on the VCC pin of the microcontroller to filter out noise from the power supply, which could affect the accuracy of the analog reference voltage. The layout of the circuit is not critical, allowing for flexibility in design and implementation.
The firmware for the voltmeter is adapted from an existing Low Cost Telemetry Device project. It has been streamlined by removing unnecessary code and incorporating functions specific to the Minimum Mass Wireless Coupler, enabling efficient data transmission without reliance on USART communication. This optimization is vital for enhancing the performance of the scanning voltmeter in wireless applications.A 10 bit scanning voltmeter with a Minimum Mass Wireless Coupler, based on the ATMega8.Range to the Minimum Mass Base Unit is 10 to 15 cm. If the voltmeter is battery operated, it can be floated from ground. This project is very simple physically, intended to demonstrate how easily the Minimum Mass RF Link can be added to a project.
The circuit shown does not have a lot if the nice things that I would usually include in an instrument, such as the ability to handle out-of-range input signals without the circuit suffering damage. Therefore, I suggest that if you build this as a stand-alone instrument, that you add protection crcuitry to the inputs.
The basic Minimum Mass Wireless Coupler technology is described and links to other projects on this site that use the Minimum Mass Wireless Coupler are located on the web page, Minimum Mass Wireless Coupler. The power suuply is the reference voltage in this case, and the binary-to-decimal conversion assumes that the refernce voltage is +5 volts, so I sugges that an adjustable regulator be used to obtain a precise +5 volts. You could use three alkaline cells (for example) in series, but the calibration would be way off. Schematic of the 4 channel scanning voltmeter. The layout isn't critical. The 33 uH choke is reduce noise from the controller's VCC pin on the analog reference voltage. The A/D converter setup and binary-to-decmial conversion routines were taken from the Low Cost Telemetry Device project on this site.
The firmware was created by taking the Low Cost Telemetry Device firmware, removing the un-needed code, and adding calls to the Minimum Mass Wireless Coupler drivers instead of to the USART routines.
Wireless Car Alarm circuit diagram
This circuit is a wireless car alarm system constructed using two modules: a transmitter module and a receiver module. It operates on FM radio waves and is suitable for vehicles with a power supply of 6-12VDC. A voltage stabilizer can...
low power led battery voltmeter
This is a low power voltmeter circuit designed for use with alternative energy systems that operate on 12V and 24V batteries. The voltmeter features an expanded scale that indicates small voltage steps within the 10 to 16 volt range for...
Voltmeter Ammeter
This voltmeter ammeter is designed to measure output voltage ranging from 0-70V to 0-500V with a resolution of 100mV and can measure current from 0-10A or more with a resolution of 10mA. It is an ideal addition to any DIY...
Wireless controlled Door-bell
The controlling range of the wireless doorbell is 100 meters. The transmitter section is designed around an oscillator transistor (BF194B) T2, which is followed by two transistors (BC148) T1 and T3. Transistor T2 generates a specific radio frequency determined by...
Ac-voltmeter
The CA081 and CA3140 BiMOS operational amplifiers provide minimal loading on the circuits being measured. The wide bandwidth and high slew rate of the CA081 enable the meter to function effectively at frequencies up to 0.5 MHz.
The CA081 and CA3140...
Digital Voltmeter and Ammeter Using CA3161E and CA3162E
The 1N4001 is a 1 Amp silicon rectifier with a voltage range of 50 to 1000 volts. It features guaranteed high-temperature soldering, high current capability, a diffused junction, low reverse leakage, and utilizes a void-free molded plastic technique for low-cost...
Video/Audio Wireless Transmitter
In this fast-paced world, there is little time for inconveniences and a greater need for portability and adaptability. The idea for an Audio/Video transmitter stems from this need. There may have been times when you’ve wanted to hook up your...
Wireless Auto Tachometer
Anyone performing their own automobile tune-ups knows how important it is to know your engine's speed. With this tachometer, you can measure your engine's speed without any connections or annoying timing lights.
The described tachometer is a non-invasive device designed for...
Digital Voltmeter
The ICL7107 is a 3 1/2 digit LED A/D converter. It contains an internal voltage reference, high isolation analog switches, sequential control logic, and the display drivers. The auto-zero adjust ensures zero reading for 0 volts input.
The ICL7107 is a...