Regulation with transistors
#transistor
#voltage regulation
#series-pass element
#error amplifier
#current source
#zener diode
#positive supply
#two transistor
Description: This page discusses the various ways that a voltage regulator can be made using two transistors. If one of these transistors is the series-pass element, then the other must be the error amplifier, so there is a distinct limit to the number of possible circuits. If we also specify that we are only interested in regulators that control the positive supply, then there are only four basic configurations to discuss. These are probably the most obvious of the four, to most readers. I guess really calling them two transistor circuits is possibly stretching things as they both show a current source to supply base current to the series-pass transistor. Yes, if conditions are right, you can use a resistor here. Circuit 1 has the reference zener in the emitter of the error amplifier. Circuit 2 has the reference zener in the base. This is rather more interesting. However, consider the situation where there is no output voltage. Clearly in this case there can also be no voltage on the base of Tr2 which therefore cannot conduct. So the circuit is quite stable in the off state. It is in fact a 'bistable' - one stable state is off and the other is regulating with an output voltage of Now this can be quite useful - if you want a tripped power supply. See Switched Power Supplies where this is the basis of the third circuit. Notice also that the term (Vz-Vbe) occurs in the formula. If you chose the zener diode correctly, its temperature coefficient can broadly cancel out the tempco of the transistor and the output voltage will be better stabilised against ambient temperature changes.
Circuit 4 probably my favourite of the four. Here R1 is driven from the In voltage so that the zener is always biased - this removes the problem of the two stable states - on and off. But there's nothing to stop you biasing the zener from the output if you wish a trip! No formula here as the output voltage if Vz, more or less. The emitter voltage of Tr2 will be Vbe less than Vz and the output will be stable one diode voltage above that. Adding the extra diode D2 is interesting: with it present a re-entrant power supply can be built. See Simple regulated power supply with overcurrent trip for a practical circuit. In this, the circuit has been turned on its head, to stabilize the negative rail, so uses a PNP series pass instead of an NPN, and it also uses a Darlington transistor instead of the single pass transistor here, but it's the same configuration.
Voltage regulators utilizing two transistors can be categorized based on their configuration and functionality. The primary configurations discussed are based on the arrangement of the error amplifier and the series-pass transistor. In these circuits, the series-pass transistor is responsible for controlling the output voltage, while the error amplifier monitors the output and adjusts the base current to the series-pass transistor accordingly.
Circuit 1 features a reference zener diode placed in the emitter of the error amplifier, allowing for a stable output voltage that is influenced by the zener voltage minus the base-emitter voltage drop (Vbe) of the transistor. Circuit 2, on the other hand, positions the zener in the base of the error amplifier, providing a different method of voltage regulation.
Circuit 3 introduces a bistable configuration where the absence of output voltage results in no base voltage for the second transistor (Tr2), effectively rendering the circuit stable in the off state. This configuration can be particularly useful for applications requiring a power supply that can be tripped.
Circuit 4 enhances the design by ensuring that the zener diode is always biased, thereby eliminating the dual stable states of on and off. The output voltage closely aligns with the zener voltage (Vz), with the emitter voltage of Tr2 being Vbe lower than Vz, resulting in a stable output. The inclusion of an additional diode (D2) allows for the creation of a re-entrant power supply, which can be particularly advantageous in applications requiring overcurrent protection.
In summary, the described circuits illustrate various methods of implementing voltage regulation using two transistors, each with unique advantages and configurations suitable for different applications in electronic design.This page discusses the various ways that a voltage regulator can be made using two transistors. If one of these transistors is the series-pass element, then the other must be the error amplifier, so there is a distinct limit to the number of possible circuits. If we also specify that we are only interested in regulators that control the positive supply, then there are only four basic configurations to discuss.
These are probably the most obvious of the four, to most readers. I guess really calling them two transistor circuits is possibly stretching things as they both show a current source to supply base current to the series-pass transistor. Yes, if conditions are right, you can use a resistor here. Circuit 1 has the reference zener in the emitter of the error amplifier. Circuit 2 has the reference zener in the base. This is rather more interesting. However, consider the situation where there is no output voltage. Clearly in this case there can also be no voltage on the base of Tr2 which therefore cannot conduct. So the circuit is quite stable in the off state. It is in fact a 'bistable' - one stable state is off and the other is regulating with an output voltage of Now this can be quite useful - if you want a tripped power supply. See Switched Power Supplies where this is the basis of the third circuit. Notice also that the term (Vz-Vbe) occurs in the formula. If you chose the zener diode correctly, its temperature coefficient can broadly cancel out the tempco of the transistor and the output voltage will be better stabilised against ambient temperature changes.
Circuit 4 Probably my favourite of the four. Here R1 is driven from the In voltage so that the zener is always biased - this removes the problem of the two stable states - on and off. But there's nothing to stop you biasing the zener from the output if you wish a trip! No formula here as the output voltage if Vz, more or less. The emitter voltage of Tr2 will be Vbe less than Vz and the output will be stable one diode voltage above that.
Adding the extra diode D2 is interesting: with it present a re-entrant power supply can be built. See Simple regulated power supply with overcurrent trip for a practical circuit. In this, the circuit has been turned on its head, to stabilize the negative rail, so uses a PNP series pass instead of an NPN, and it also uses a Darlington transistor instead of the single pass transistor here, but it's the same configuration.
Circuit 4 probably my favourite of the four. Here R1 is driven from the In voltage so that the zener is always biased - this removes the problem of the two stable states - on and off. But there's nothing to stop you biasing the zener from the output if you wish a trip! No formula here as the output voltage if Vz, more or less. The emitter voltage of Tr2 will be Vbe less than Vz and the output will be stable one diode voltage above that. Adding the extra diode D2 is interesting: with it present a re-entrant power supply can be built. See Simple regulated power supply with overcurrent trip for a practical circuit. In this, the circuit has been turned on its head, to stabilize the negative rail, so uses a PNP series pass instead of an NPN, and it also uses a Darlington transistor instead of the single pass transistor here, but it's the same configuration.
Voltage regulators utilizing two transistors can be categorized based on their configuration and functionality. The primary configurations discussed are based on the arrangement of the error amplifier and the series-pass transistor. In these circuits, the series-pass transistor is responsible for controlling the output voltage, while the error amplifier monitors the output and adjusts the base current to the series-pass transistor accordingly.
Circuit 1 features a reference zener diode placed in the emitter of the error amplifier, allowing for a stable output voltage that is influenced by the zener voltage minus the base-emitter voltage drop (Vbe) of the transistor. Circuit 2, on the other hand, positions the zener in the base of the error amplifier, providing a different method of voltage regulation.
Circuit 3 introduces a bistable configuration where the absence of output voltage results in no base voltage for the second transistor (Tr2), effectively rendering the circuit stable in the off state. This configuration can be particularly useful for applications requiring a power supply that can be tripped.
Circuit 4 enhances the design by ensuring that the zener diode is always biased, thereby eliminating the dual stable states of on and off. The output voltage closely aligns with the zener voltage (Vz), with the emitter voltage of Tr2 being Vbe lower than Vz, resulting in a stable output. The inclusion of an additional diode (D2) allows for the creation of a re-entrant power supply, which can be particularly advantageous in applications requiring overcurrent protection.
In summary, the described circuits illustrate various methods of implementing voltage regulation using two transistors, each with unique advantages and configurations suitable for different applications in electronic design.This page discusses the various ways that a voltage regulator can be made using two transistors. If one of these transistors is the series-pass element, then the other must be the error amplifier, so there is a distinct limit to the number of possible circuits. If we also specify that we are only interested in regulators that control the positive supply, then there are only four basic configurations to discuss.
These are probably the most obvious of the four, to most readers. I guess really calling them two transistor circuits is possibly stretching things as they both show a current source to supply base current to the series-pass transistor. Yes, if conditions are right, you can use a resistor here. Circuit 1 has the reference zener in the emitter of the error amplifier. Circuit 2 has the reference zener in the base. This is rather more interesting. However, consider the situation where there is no output voltage. Clearly in this case there can also be no voltage on the base of Tr2 which therefore cannot conduct. So the circuit is quite stable in the off state. It is in fact a 'bistable' - one stable state is off and the other is regulating with an output voltage of Now this can be quite useful - if you want a tripped power supply. See Switched Power Supplies where this is the basis of the third circuit. Notice also that the term (Vz-Vbe) occurs in the formula. If you chose the zener diode correctly, its temperature coefficient can broadly cancel out the tempco of the transistor and the output voltage will be better stabilised against ambient temperature changes.
Circuit 4 Probably my favourite of the four. Here R1 is driven from the In voltage so that the zener is always biased - this removes the problem of the two stable states - on and off. But there's nothing to stop you biasing the zener from the output if you wish a trip! No formula here as the output voltage if Vz, more or less. The emitter voltage of Tr2 will be Vbe less than Vz and the output will be stable one diode voltage above that.
Adding the extra diode D2 is interesting: with it present a re-entrant power supply can be built. See Simple regulated power supply with overcurrent trip for a practical circuit. In this, the circuit has been turned on its head, to stabilize the negative rail, so uses a PNP series pass instead of an NPN, and it also uses a Darlington transistor instead of the single pass transistor here, but it's the same configuration.
Flasher Circuits
The basic two-transistor flasher has become widely utilized in various applications due to its simplicity and versatility. It has been employed in circuits such as a micropower low battery indicator, a lightning detector, an off-line switching power supply, a micropower...
2 Transistor LED Flasher
This is a classic 2-transistor astable multivibrator. Many other NPN small signal or switching transistors can be used, including 2N4401, PN2222, or 2N2222 using the circuit on the left. The circuit can also be inverted using PNP transistors such as...
A common emitter amplifier
A common emitter amplifier is a total pole amplification circuit structure featuring a key emitting device. This circuit refers to the emitter of the input signal and the output signal connected to a common ground, forming the basis of fundamental...
Single junction transistor pulse width trigger circuit
A conventional single junction transistor trigger circuit is limited to producing narrow pulses due to the rapid turn-off characteristics of the single-junction transistor. To address this limitation, a PNP transistor is added to the single-junction transistor trigger circuit, which allows...
50 Watt Amplifier Circuit Using Transistor
This circuit is a robust and efficient power amplifier suitable for various audio applications. It delivers 60W RMS output at a 50V supply with an 8 Ohm load. The design is user-friendly, allowing for the use of non-critical components that...
Kapanadze 5
The emitter voltage drops completely to 0V from 42V during the pulse when the transistor is conducting or saturated. This contrasts with a pure resistive load (the 4.7 Ohm resistor mentioned in the previous video), where the collector-emitter voltage does...
Speech compression circuit diagram
An amplifier designed to achieve a voltage gain of approximately 20, utilizing the MPS6517 PNP transistor in the emitter follower configuration. The RI controller allows for adjustment of the transistor's quiescent point. The output signal is activated only when the...
Regulated 12 Volt Supply
This circuit utilizes a 13-volt zener diode (D2) for voltage regulation. Approximately 0.7 volts are dropped across the base-emitter junction of the transistors, resulting in a higher current output of 12.3 volts. The circuit is capable of supplying loads up...
Long-Duration Time Delay
Transistor Q1 and resistors R1, R2, and R3 form a constant current source, with the charge current adjustable to as low as a few nanoamperes. This current is insufficient to activate the UJT, where IP is 0.2 A, unless a...