Transistor current mirror circuit
#transistor
#current mirror
#analog circuit
#current source
#matched pair
#bipolar junction transistor
#BJT
#circuit design
#electronics
#semiconductor
Description: The bases and emitters of the transistors are connected together, resulting in equal base-emitter voltages. Assuming the transistors are identical, equal Vbe leads to equal base currents, which in turn results in equal collector-emitter currents. By adjusting the voltage and resistance in one transistor, the current through the other transistor is also set. An approach for overcurrent detection involves placing a second resistor in the mirrored leg and measuring the voltage across it. If this voltage exceeds a predetermined level, it indicates that the current has surpassed the setpoint. However, the efficacy of this method compared to measuring the voltage on the primary leg is uncertain. The circuit is designed to monitor the safe current sourced by the supply, enabling overcurrent detection. An alternative suggestion includes placing a resistor between the secondary source and the secondary transistor to measure voltage across that resistor. Nonetheless, using a shunt resistor in the primary is simpler and yields similar results. Current mirrors are commonly utilized in overcurrent protection systems because they facilitate a voltage reference shift from Vin to ground. Implementing a high-side current mirror with PNP transistors and positioning the secondary load between the collector of the secondary transistor and ground provides a ground-referenced voltage proportional to the high-side load current. The resistor value can be adjusted to determine the circuit's gain.
The described circuit employs a configuration of transistors where the bases and emitters are interconnected, ensuring that the base-emitter voltages (Vbe) remain consistent across the devices. This arrangement is crucial for maintaining equal currents flowing through the base and subsequently through the collector-emitter paths of the transistors. The principle of current mirroring is applied here, which is fundamental in various analog applications, including overcurrent protection systems.
To implement an overcurrent detection mechanism, a secondary resistor can be introduced in the mirrored leg of the circuit. The voltage drop across this resistor is monitored; if it exceeds a specified threshold, it indicates that the current flowing through the circuit has surpassed the safe operating limit. This method allows for a precise measurement of the current without directly interfering with the primary circuit operation.
Alternatively, the circuit can be simplified by placing a shunt resistor in the primary leg, which provides a direct measurement of the current flowing through the supply. This alternative method is often preferred due to its straightforward implementation and effectiveness in providing accurate current readings.
Current mirrors are particularly advantageous in high-side applications where the load is connected to a positive supply voltage. By using PNP transistors in the current mirror configuration, the circuit can reference the ground voltage, making it easier to monitor the load current. The secondary load is connected between the collector of the secondary transistor and ground, allowing for a proportional voltage signal that reflects the load current. This configuration enhances the reliability of the overcurrent protection system by ensuring that the voltage reference remains stable and accurately reflects the operating conditions.
The gain of the circuit can be adjusted by varying the resistor values, allowing for fine-tuning of the sensitivity and response of the overcurrent detection mechanism. This flexibility is essential for adapting the circuit to different applications and ensuring optimal performance in various operating environments. Overall, the described circuit provides a robust solution for monitoring and protecting against overcurrent conditions in electronic systems.The bases and emitters are tied together, so the base-emitter voltages are equal. Since we assume the transistors themselves are identical, equal Vbe means equal current into the base. And equal current into the base means equal current from collector to emitter. Thus by setting the current through one, by the selection of voltage and resistance, you also set the current through the other. One way of doing an overcurrent detector would be to put a second resistor in the mirrored leg, and measure the voltage across that resistor. If it rises above some fixed level, the current must have exceeded your setpoint. I`m not immediately sure why that would be better than measuring the voltage on the primary leg, though.
At first glance, this seems like a pretty round-about way of doing an overcurrent limit. Thanks Remiel. I have a supply and the load between which this circuit is connected to monitor the safe current that is sourced by the supply. So I need to use this circuit to detect the over current drawn from the supply. So is there anyway that i can do with this Durgaprasad Mar 20 `13 at 17:02 Yes, you could put a resistor between the secondary source and the secondary transistor, and measure the voltage across that resistor.
But again, a shunt resistor in the primary would be simpler and should have nearly identical effect. Stephen Collings Mar 20 `13 at 18:21 Current mirrors are often used in overcurrent protection because it allows a shift of the voltage reference from Vin to Gnd. Use a high-side current mirror (PNP transistors instead of NPN) and put the "secondary load" between the collector of the secondary transistor and ground.
Now you have a ground-referenced voltage that`s proportional to the high-side load current. Note that the value of the resistor can be varied to determine the "gain" of the circuit.
The described circuit employs a configuration of transistors where the bases and emitters are interconnected, ensuring that the base-emitter voltages (Vbe) remain consistent across the devices. This arrangement is crucial for maintaining equal currents flowing through the base and subsequently through the collector-emitter paths of the transistors. The principle of current mirroring is applied here, which is fundamental in various analog applications, including overcurrent protection systems.
To implement an overcurrent detection mechanism, a secondary resistor can be introduced in the mirrored leg of the circuit. The voltage drop across this resistor is monitored; if it exceeds a specified threshold, it indicates that the current flowing through the circuit has surpassed the safe operating limit. This method allows for a precise measurement of the current without directly interfering with the primary circuit operation.
Alternatively, the circuit can be simplified by placing a shunt resistor in the primary leg, which provides a direct measurement of the current flowing through the supply. This alternative method is often preferred due to its straightforward implementation and effectiveness in providing accurate current readings.
Current mirrors are particularly advantageous in high-side applications where the load is connected to a positive supply voltage. By using PNP transistors in the current mirror configuration, the circuit can reference the ground voltage, making it easier to monitor the load current. The secondary load is connected between the collector of the secondary transistor and ground, allowing for a proportional voltage signal that reflects the load current. This configuration enhances the reliability of the overcurrent protection system by ensuring that the voltage reference remains stable and accurately reflects the operating conditions.
The gain of the circuit can be adjusted by varying the resistor values, allowing for fine-tuning of the sensitivity and response of the overcurrent detection mechanism. This flexibility is essential for adapting the circuit to different applications and ensuring optimal performance in various operating environments. Overall, the described circuit provides a robust solution for monitoring and protecting against overcurrent conditions in electronic systems.The bases and emitters are tied together, so the base-emitter voltages are equal. Since we assume the transistors themselves are identical, equal Vbe means equal current into the base. And equal current into the base means equal current from collector to emitter. Thus by setting the current through one, by the selection of voltage and resistance, you also set the current through the other. One way of doing an overcurrent detector would be to put a second resistor in the mirrored leg, and measure the voltage across that resistor. If it rises above some fixed level, the current must have exceeded your setpoint. I`m not immediately sure why that would be better than measuring the voltage on the primary leg, though.
At first glance, this seems like a pretty round-about way of doing an overcurrent limit. Thanks Remiel. I have a supply and the load between which this circuit is connected to monitor the safe current that is sourced by the supply. So I need to use this circuit to detect the over current drawn from the supply. So is there anyway that i can do with this Durgaprasad Mar 20 `13 at 17:02 Yes, you could put a resistor between the secondary source and the secondary transistor, and measure the voltage across that resistor.
But again, a shunt resistor in the primary would be simpler and should have nearly identical effect. Stephen Collings Mar 20 `13 at 18:21 Current mirrors are often used in overcurrent protection because it allows a shift of the voltage reference from Vin to Gnd. Use a high-side current mirror (PNP transistors instead of NPN) and put the "secondary load" between the collector of the secondary transistor and ground.
Now you have a ground-referenced voltage that`s proportional to the high-side load current. Note that the value of the resistor can be varied to determine the "gain" of the circuit.
Dynamic Microphone Preamplifier using C945 transistor
This circuit utilizes three transistors (2SC945, 2C1815, or 2SC828) as the primary components, functioning as a typical low-noise transistor amplifier. It offers a gain of approximately 200 to 300 times and has a frequency response ranging from 50Hz to 100KHz....
Transistor Organ
This simple circuit can provide hours of enjoyment as you learn tunes, play duets or just make some really weird sounds by pushing all the buttons at once. You have probably seen this circuit before, it is fairly common. I...
Transistors UHF tuner circuit
The circuit features an adjustable prestage utilizing the AF279 transistor, while the natural oscillation mixer stage employs the AF280 transistor. The power circuit is mounted on a board with copper coating. The main coil specifications are as follows: L1, L3,...
Single-junction transistor sine wave oscillator circuit
The single-junction transistor is commonly utilized in sawtooth and pulse generators, and it can also be configured to create a basic sine wave generation circuit. As an oscillator circuit composed of discrete components, it requires a minimal number of parts....
Motor vehicle steering flasher 12
The motor vehicle steering flasher described in the example utilizes high-power transistors as electronic switches, and the circuit is simple and easy to construct. The motor vehicle steering flasher consists of the flash circuit with resistors R1-R3, a capacitor C,...
TRANSISTORIZED AM RADIO
The schematic illustrates a standard AM radio circuit utilizing NPN transistors. This generic circuit does not provide specific values for all components, serving instead as a reference point for experimenters to begin their projects.
The schematic of a typical transistor AM...
Current Source
This circuit utilizes commonly available components to create a 0-to-200-nA current source. It incorporates a PMOS transistor from the input stage of a DC4007A, which is more accessible than a standalone PMOS transistor. The CA3130 operational amplifier functions as a...
TRANSISTORIZED THYRATRON RING COUNTER
Each bistable circuit comprises two oppositely-symmetrical germanium transistors, two diodes, and four resistors. An additional transistor, Q, facilitates the transition of the conducting state to the next position when actuated by a transfer pulse. The absence of capacitors allows for...
Direct Coupled Discrete Astable Multivibrator circuit
This flip-flop circuit functions as a free-running astable multivibrator, where the bases and collectors of both emitter-biased transistors are directly coupled. The switching action is facilitated by a capacitor in each emitter circuit, resulting in the generation of triangle waves...