alternating flasher circuit diagram
#555 timer
#astable multivibrator
#flasher
#relay
#diodes
#timing circuit
#LED
#flashing lights
#pulse generator
#circuit protection
Description: This circuit utilizes three readily available 555 timer integrated circuits (ICs), all functioning as astable multivibrators. The first 555 timer has both an on period and an off period of 1 second. This IC regulates the on/off intervals of the other two 555 timers, which are employed to flash two bulbs via relay contacts. Diodes are incorporated to safeguard the 555 ICs from voltage spikes. The relays should possess an impedance exceeding 50 ohms, meaning they should not draw more than 200 mA of current. The bulbs connected to the first relay flash for approximately 1 second at a frequency of 4 flashes per second. Subsequently, the bulbs linked to the second relay also flash for 1 second at the same frequency. This cycle continues to repeat.
The circuit design incorporates three 555 timer ICs, configured as astable multivibrators to create a flashing light effect. The primary 555 timer is responsible for generating a square wave signal with a frequency of 4 Hz, resulting in an on/off cycle of 1 second. This output controls the timing of the second and third 555 timers, which are set to the same frequency, ensuring synchronized operation.
The first 555 timer is connected in a standard astable configuration, with resistors and capacitors selected to achieve the desired timing intervals. The output pin of this timer drives the base of a transistor, which in turn controls the relay that powers the first bulb. The use of diodes across the relay coils is crucial for protecting the 555 ICs from back EMF generated when the relays are de-energized.
The second 555 timer is similarly configured and is activated by the output of the first timer. It controls a second relay, which operates the second bulb. Both relays must be chosen with care, ensuring that their impedance is greater than 50 ohms to limit current draw to under 200 mA, thus protecting the circuit components from overheating and damage.
This circuit can be effectively used in various applications requiring flashing lights, such as decorative lighting, indicators, or alarms. The repeating cycle of flashing is achieved through the continuous operation of the 555 timers, which maintain a consistent output without the need for additional control circuitry. Overall, this design exemplifies a straightforward yet effective use of timer ICs in creating a visually engaging light display.This circuit uses three easily available 555 timer ICs. All three work as astable multivibrators. The first 555 has an on period and off period equal to 1 sec. This IC controls the on/ off periods of the other 2 555s which are used to flash two bulbs through the relay contacts. The diodes are used to protect the 555 ICs from peaks. The relays shou ld have an impedance greater than 50ohms i. e, they should not draw a current more than 200mA. The bulb(s) connected to the first relay flashes for about 1 sec at a rate of 4 flashes per second. Then the bulb(s) connected to the second relay flashes for 1 sec at a rate of 4 flashes per second. Then the cycle repeats. Disclaimer: All the information present on this site are for personal use only. No commercial use is permitted without the prior permission from authors of this website. All content on this site is provided as is and without any guarantee on any kind, implied or otherwise. We cannot be held responsible for any errors, omissions, or damages arising out of use of information available on this web site.
The content in this site may contain COPYRIGHTED information and should not be reproduced in any way without prior permission from the authors.
The circuit design incorporates three 555 timer ICs, configured as astable multivibrators to create a flashing light effect. The primary 555 timer is responsible for generating a square wave signal with a frequency of 4 Hz, resulting in an on/off cycle of 1 second. This output controls the timing of the second and third 555 timers, which are set to the same frequency, ensuring synchronized operation.
The first 555 timer is connected in a standard astable configuration, with resistors and capacitors selected to achieve the desired timing intervals. The output pin of this timer drives the base of a transistor, which in turn controls the relay that powers the first bulb. The use of diodes across the relay coils is crucial for protecting the 555 ICs from back EMF generated when the relays are de-energized.
The second 555 timer is similarly configured and is activated by the output of the first timer. It controls a second relay, which operates the second bulb. Both relays must be chosen with care, ensuring that their impedance is greater than 50 ohms to limit current draw to under 200 mA, thus protecting the circuit components from overheating and damage.
This circuit can be effectively used in various applications requiring flashing lights, such as decorative lighting, indicators, or alarms. The repeating cycle of flashing is achieved through the continuous operation of the 555 timers, which maintain a consistent output without the need for additional control circuitry. Overall, this design exemplifies a straightforward yet effective use of timer ICs in creating a visually engaging light display.This circuit uses three easily available 555 timer ICs. All three work as astable multivibrators. The first 555 has an on period and off period equal to 1 sec. This IC controls the on/ off periods of the other 2 555s which are used to flash two bulbs through the relay contacts. The diodes are used to protect the 555 ICs from peaks. The relays shou ld have an impedance greater than 50ohms i. e, they should not draw a current more than 200mA. The bulb(s) connected to the first relay flashes for about 1 sec at a rate of 4 flashes per second. Then the bulb(s) connected to the second relay flashes for 1 sec at a rate of 4 flashes per second. Then the cycle repeats. Disclaimer: All the information present on this site are for personal use only. No commercial use is permitted without the prior permission from authors of this website. All content on this site is provided as is and without any guarantee on any kind, implied or otherwise. We cannot be held responsible for any errors, omissions, or damages arising out of use of information available on this web site.
The content in this site may contain COPYRIGHTED information and should not be reproduced in any way without prior permission from the authors.
Beeper driver with 555
This circuit produces the sound of a beeper like the one in pagers which produces a "beep-beep" sound. Basically the circuit consists of a 555 timer oscillator which is turned ON and OFF periodically. The first IC (left) oscillates at...
Ice warning and lights reminder
This device informs a driver whether their lights should be activated and warns them if the outside temperature approaches zero degrees Celsius by illuminating an LED and sounding a buzzer. The sensitivity can be adjusted using VR1, and the light-dependent...
LED Boost Circuit
The completed board may be driven by voltages between 0.8 and 3 Volts. While the basic design goal was candle-like light from a single cell, the values used were chosen to allow safe operation from 3 Volts so you can,...
2 LED CMOS Flasher
Two LED CMOS Flasher Circuit Diagram. This is a simple two LED CMOS robot (flasher, multivibrator) circuit using CD4069 six inverters.
The two LED CMOS flasher circuit utilizes the CD4069 integrated circuit, which contains six inverters, to create a multivibrator configuration....
Long-Interval Pulse Generator
A rectangular-wave pulse generator with an extremely long period can be constructed using only two components: a National Semiconductor LM3710 supervisor integrated circuit (IC) and a 100-nF capacitor to suppress noise spikes. This circuit leverages the watchdog and reset timers...
555 Pulse generator
The first positive pulse from a classic 555-based oscillator is always 1.6 times longer than the subsequent pulses. This discrepancy occurs because, during the initial cycle, capacitor C2 begins charging from 0 V. While this is typically not an issue,...
Bonsai electronic circuit
The electronic components designed by conventional electronic bonsai create a sparkling and brilliant atmosphere in the living room, enhancing the joys and pleasures of life. The selection of components includes IC1 to IC4, which consist of two pairs of D...
Basic Led circuit driver
A basic LED driver circuit consists of a 5-volt power source, a 2 kΩ potentiometer, and an LED. The LED is forward biased, with the manufacturer specifying a maximum current rating of 20 mA at a diode voltage drop of...
Display Backlighting Using High-Brightness LEDs and SEPIC Power Modules
This application note discusses the use of SEPIC power modules to supply the necessary power for driving high-brightness LED arrays. These arrays serve as display backlights and necessitate a wide dimming range. The SEPIC configuration offers an efficient and adaptable...