The Original 2 Phone Link=
Description: This circuit initiated the development of various Link Telephone Intercom designs. Originally created in 1996 using heavy-duty relays and contact banks, it was updated last year to incorporate IC1 in place of a simpler transistor multivibrator. All relays and contact banks were replaced with optocouplers, and two transformers were added as part of the transmission bridge, which previously included the relay coils. This circuit is ideal for simple communication between two phones, offering a compact design that is more economical in terms of power consumption, allowing operation from batteries, such as a 12-volt Gel Cell. It has no moving parts, except for the switch hooks in each phone handset. This early Link design operates by allowing either caller to pick up their handset to 'buzz' the other phone. There are no numbers to dial and no dial tone; instead, a ringing tone pulses on and off in sync with the buzzer at either end during a call.
When phone #1 picks up its handset, a DC loop is formed between the handset, the 1k winding of Tx1, the 0V earth terminal, the +12 volts terminal, and the LEDs inside OC1 and OC3. IC1, an NE556 dual timer chip, is continuously active, pulsing on and off at output pin 9, which drives the second half of the timer chip via D1 to pin 4, generating ring pulses and a ringing tone from pin 5 through capacitors C3 and C4 to the 8-ohm windings of Tx1 and Tx2. The transistor within OC1 switches on hard, pulling its collector lead low, allowing ring pulses from pin 9 of IC1 to flow through R5 and Q1 to the emitter of OC1, then to its collector lead, which connects to the negative lead of buzzer B2, thus signaling the other phone.
When the second phone is picked up, OC2 and OC4 also form a DC loop with the 1k winding of Tx2 and the LEDs within the optocouplers. The transistors in OC1 and OC2 create a link to the +12 volts supply near phone #1, routed through diode D2 to the junction of pins 12 and 8 of IC1. This effectively stops the ringing, halting both ring pulses from pin 9 and the ringing tone from pin 5 for the duration of the call. Once both phones are returned to the on-hook position, all four optocouplers (OC1 to OC4) deactivate, allowing IC1 to resume pulsing and providing the ringing tone. However, neither of these outputs will affect the handsets until one is picked up again to initiate the next call.
The transmission bridge consists of Tx1 and OC3, along with Tx2 and OC4, as well as capacitors C5 and C6. The 1k windings serve to prevent speech signals (AC signals) from being grounded through the earth connection. The capacitors facilitate the passage of these signals between handsets while blocking any DC voltages that could cause interference. This circuit represents a simplified version of the Stone Transmission Bridge, which is well-suited for its intended purpose.This is the circuit that sparked off all the other Link Telephone Intercom designs. Originally designed back in 1996 with heavy duty relays and their contact banks, it was updated late last year with the addition of IC1 in place of a simpler transistor multivibrator, the replacement of all relays and contact banks with optocouplers, and the additi on of the two transformers as part of the transmission bridge (see explanation below) which was comprised partly of the relay coils. If you just want simple ‘no frills ’ communication from one phone to another, then this is the right circuit for you!
This version is much more compact, more economic on power drain (yes, you can run it off of batteries – eg: a 12 volt Gel Cell!) and has no moving parts, except for the switch hooks inside each of the phone handsets. This was one of the earliest Link designs. It works by either caller simply picking up their handset and ‘buzzing ’ the other phone. There are no numbers to dial (in fact, no dial tone either – just ring tone, which pulses on and off in unison with the buzzer at either end when a call is in progress.
) Let ’s assume that #1 picks up their handset. This forms a DC loop between the handset, the 1k winding of Tx1, the 0v_ earth terminal, the +12 volts terminal and the leds inside OC1 and OC3. IC1 (an NE556 dual timer chip) is always ‘on ’ –that is, it ’s always pulsing on and off at output pin 9, which then drives the second half of the timer chip on and off via D1 to pin 4, producing ring pulses, and ring tone from pin 5 via C3 and C4 to the 8R windings of Tx1 and Tx2.
The transistor inside OC1 switches on hard, taking its collector lead low, and ring pulses are fed from pin 9 of IC1 via R5 and Q1, to the emitter of OC1, through to its collector lead, and then on to the –ve lead of buzzer B2, thus ‘buzzing ’ the other phone. When that phone is picked up off hook, OC2 and OC4 also form a DC loop along with the 1k winding of Tx2 and the leds inside the optocouplers.
The transistors inside OC1 and OC2 now form a ‘link ’ (no pun intended) from the +12 volts supply (shown at left near phone #1) through to the junction of pins 12 and 8 of IC1, via diode D2. This effectively halts the ringer, and both ring pulses from pin 9 and ring tone from pin 5 cease for the duration of the call.
When both phones are hung up back to the on hook position, all four optocouplers (OC1 to OC4) are switched off. IC1 will now resume pulsing and providing ring tone, but neither one of these outputs will have any effect on either phone handset, until one or the other is picked up off hook again, to make the next call.
The ‘transmission bridge ’ mentioned earlier, comprises of Tx1 and OC3 along with Tx2 and OC4, as well as C5 and C6. Basically, the 1k windings prevent speech signals (which are an AC signal) from being grounded through the earth connection.
The two capacitors allow these signals to pass between the handsets, but block any DC voltages from interfering with them. This circuit is known as a Stone Transmission Bridge ” and although I have employed a simplified version of it, it ’s quite suitable for our purposes.
Happy chatting on the line … ©Austin Hellier 1996 - 2003.
When phone #1 picks up its handset, a DC loop is formed between the handset, the 1k winding of Tx1, the 0V earth terminal, the +12 volts terminal, and the LEDs inside OC1 and OC3. IC1, an NE556 dual timer chip, is continuously active, pulsing on and off at output pin 9, which drives the second half of the timer chip via D1 to pin 4, generating ring pulses and a ringing tone from pin 5 through capacitors C3 and C4 to the 8-ohm windings of Tx1 and Tx2. The transistor within OC1 switches on hard, pulling its collector lead low, allowing ring pulses from pin 9 of IC1 to flow through R5 and Q1 to the emitter of OC1, then to its collector lead, which connects to the negative lead of buzzer B2, thus signaling the other phone.
When the second phone is picked up, OC2 and OC4 also form a DC loop with the 1k winding of Tx2 and the LEDs within the optocouplers. The transistors in OC1 and OC2 create a link to the +12 volts supply near phone #1, routed through diode D2 to the junction of pins 12 and 8 of IC1. This effectively stops the ringing, halting both ring pulses from pin 9 and the ringing tone from pin 5 for the duration of the call. Once both phones are returned to the on-hook position, all four optocouplers (OC1 to OC4) deactivate, allowing IC1 to resume pulsing and providing the ringing tone. However, neither of these outputs will affect the handsets until one is picked up again to initiate the next call.
The transmission bridge consists of Tx1 and OC3, along with Tx2 and OC4, as well as capacitors C5 and C6. The 1k windings serve to prevent speech signals (AC signals) from being grounded through the earth connection. The capacitors facilitate the passage of these signals between handsets while blocking any DC voltages that could cause interference. This circuit represents a simplified version of the Stone Transmission Bridge, which is well-suited for its intended purpose.This is the circuit that sparked off all the other Link Telephone Intercom designs. Originally designed back in 1996 with heavy duty relays and their contact banks, it was updated late last year with the addition of IC1 in place of a simpler transistor multivibrator, the replacement of all relays and contact banks with optocouplers, and the additi on of the two transformers as part of the transmission bridge (see explanation below) which was comprised partly of the relay coils. If you just want simple ‘no frills ’ communication from one phone to another, then this is the right circuit for you!
This version is much more compact, more economic on power drain (yes, you can run it off of batteries – eg: a 12 volt Gel Cell!) and has no moving parts, except for the switch hooks inside each of the phone handsets. This was one of the earliest Link designs. It works by either caller simply picking up their handset and ‘buzzing ’ the other phone. There are no numbers to dial (in fact, no dial tone either – just ring tone, which pulses on and off in unison with the buzzer at either end when a call is in progress.
) Let ’s assume that #1 picks up their handset. This forms a DC loop between the handset, the 1k winding of Tx1, the 0v_ earth terminal, the +12 volts terminal and the leds inside OC1 and OC3. IC1 (an NE556 dual timer chip) is always ‘on ’ –that is, it ’s always pulsing on and off at output pin 9, which then drives the second half of the timer chip on and off via D1 to pin 4, producing ring pulses, and ring tone from pin 5 via C3 and C4 to the 8R windings of Tx1 and Tx2.
The transistor inside OC1 switches on hard, taking its collector lead low, and ring pulses are fed from pin 9 of IC1 via R5 and Q1, to the emitter of OC1, through to its collector lead, and then on to the –ve lead of buzzer B2, thus ‘buzzing ’ the other phone. When that phone is picked up off hook, OC2 and OC4 also form a DC loop along with the 1k winding of Tx2 and the leds inside the optocouplers.
The transistors inside OC1 and OC2 now form a ‘link ’ (no pun intended) from the +12 volts supply (shown at left near phone #1) through to the junction of pins 12 and 8 of IC1, via diode D2. This effectively halts the ringer, and both ring pulses from pin 9 and ring tone from pin 5 cease for the duration of the call.
When both phones are hung up back to the on hook position, all four optocouplers (OC1 to OC4) are switched off. IC1 will now resume pulsing and providing ring tone, but neither one of these outputs will have any effect on either phone handset, until one or the other is picked up off hook again, to make the next call.
The ‘transmission bridge ’ mentioned earlier, comprises of Tx1 and OC3 along with Tx2 and OC4, as well as C5 and C6. Basically, the 1k windings prevent speech signals (which are an AC signal) from being grounded through the earth connection.
The two capacitors allow these signals to pass between the handsets, but block any DC voltages from interfering with them. This circuit is known as a Stone Transmission Bridge ” and although I have employed a simplified version of it, it ’s quite suitable for our purposes.
Happy chatting on the line … ©Austin Hellier 1996 - 2003.
Automatic telephone call recording circuit
The DC voltage present on the telephone line typically ranges from 45 to 50V when on-hook and drops to approximately 6V when off-hook. This condition activates a step-down circuit relay, which in turn controls a tape recorder. Audio input is...
Internal telephone circuit
The internal telephone circuit is depicted below. By making minor enhancements to a toy telephone, it can be transformed into a functional internal telephone. This device comprises several components, including the phone unit, a decoding circuit, a ringing circuit, and...
telephone sharer circuit 9
To utilize this facility, the calling subscriber must first dial the standard phone number of the intended recipient. Once the call is connected, the calling party does not hear a ring-back tone. The calling subscriber must then press the asterisk...
Irregular Flasher
Two multivibrators with different frequencies can be constructed using the NAND gates of a 4011 integrated circuit (IC). When the output of IC1, pin B is positive in relation to pin C, LED D1 illuminates. As the states of IC1,...
Telephone control automatic lamp circuit 1
An automatic light system is integrated with a telephone block system. When the phone rings, the owner is prompted to pick up the handset or pull a lever, causing the lamp to light up. If there is no contact or...
High Quality Intercom
This circuit consists of two identical intercom units. Each unit contains a power supply, microphone preamplifier, audio amplifier, and a Push To Talk (PTT) relay circuit. Only two wires are required to connect the units together. Due to the low...
Intercommunication (Intercom) circuit
This intercom circuit is versatile and can be utilized in various applications. It operates at 22V, although it may function at a lower voltage (experimental testing is suggested). The circuit utilizes a loudspeaker with an impedance of 20-45 Ohms on...
VERY SIMPLE TELEPHONE INTERCOM CIRCUIT
Tro telephones can be utilized as an intercom through the implementation of this circuit. Traditional rotary phones, particularly those that are non-electronic, may be the most effective for this purpose. Additionally, this method can also power handsets alone.
The circuit designed...
Telephone Status Indicator Circuit
This simple circuit indicates the status of a phone, including Line OK, Dialing, and Call Attended. It also features a locking mechanism to block outgoing calls while allowing incoming calls, preventing misuse of the telephone. The circuit requires only a...