Telephone Ring Generator Using Switching Supply
#telephone
#ring generator
#switching supply
#SMPS
#high voltage
#CMOS Schmitt Trigger
#oscillator
#inductor
#transistor
Description: The telephone ring generator shown below generates the needed high voltage from a simple switching mode power supply (SMPS) which employs a CMOS Schmitt Trigger square wave oscillator, 10 mH inductor, high voltage switching transistor (TIP47 or other high voltage, 1 amp transistor) and a driver transistor (2N3053). The inductor should have a low DC resistance of 1.5 ohms or less. The switching supply must have a load connected to prevent the voltage from rising too high, so a 22K resistor is used across the output which limits the voltage to about 120 DC with the phone ringer disconnected and about 90 volts DC connected. The output voltage can be adjusted by changing the value of the 150K resistor between pins 10 and 11 which will alter the oscillator frequency (frequency is around 800 Hz as shown). The supply is gated on and off by a second Schmitt Trigger oscillator (pins 12/13) so that the phone rings for about 2 seconds and then the circuit idles for about a minute between rings. These times can be adjusted with the 10K and 300K resistors connected to pin 12.
The telephone ring generator circuit operates by converting a low voltage input into a high voltage output suitable for ringing a telephone. The core of this circuit is a switching mode power supply (SMPS) that utilizes a CMOS Schmitt Trigger square wave oscillator. This oscillator generates a square wave signal that drives a high voltage switching transistor, such as the TIP47, which is capable of handling high voltage and current levels.
The design incorporates a 10 mH inductor, which is crucial for energy storage and transfer in the SMPS. The inductor must have a low DC resistance, ideally around 1.5 ohms, to ensure efficient operation and minimize power losses. The circuit also includes a driver transistor (2N3053) that amplifies the control signals to drive the high voltage transistor effectively.
To protect the circuit from excessive voltage, a 22K resistor is placed across the output. This resistor serves as a load, limiting the voltage to approximately 120 volts DC when the phone ringer is disconnected and around 90 volts DC when connected. The output voltage can be fine-tuned by adjusting a 150K resistor located between pins 10 and 11 of the oscillator circuit. This adjustment alters the frequency of the oscillator, which is typically around 800 Hz, a frequency suitable for telephone ringing.
The circuit is designed to produce a ringing signal for a duration of about 2 seconds, followed by a pause of approximately one minute between rings. This timing is controlled by a second Schmitt Trigger oscillator connected to pins 12 and 13. The timing intervals can be modified by changing the values of the 10K and 300K resistors connected to pin 12, allowing for customization of the ringing pattern based on user requirements.
In summary, this telephone ring generator circuit effectively combines various components and configurations to produce a reliable high voltage ringing signal, ensuring compatibility with standard telephone systems while allowing for adjustments in both output voltage and ringing duration.The telephone ring generator shown below generates the needed high voltage from a simple switching mode power supply (SMPS) which employs a CMOS Schmitt Trigger square wave oscillator, 10 mH inductor, high voltage switching transistor (TIP47 or other high voltage, 1 amp transistor) and a driver transistor (2N3053). The inductor should have a low DC resistance of 1.5 ohms or less. The switching supply must have a load connected to prevent the voltage from rising too high, so a 22K resistor is used across the output which limits the voltage to about 120 DC with the phone ringer disconnected and about 90 volts DC connected.
The output voltage can be adjusted by changing the value of the 150K resistor between pins 10 and 11 which will alter the oscillator frequency (frequency is around 800 Hz as shown). The supply is gated on and off by a second Schmitt Trigger oscillator (pins 12/13) so that the phone rings for about 2 seconds and then the circuit idles for about a minute between rings.
These times can be adjusted with the 10K and 300K resistors connected to pin 12.
The telephone ring generator circuit operates by converting a low voltage input into a high voltage output suitable for ringing a telephone. The core of this circuit is a switching mode power supply (SMPS) that utilizes a CMOS Schmitt Trigger square wave oscillator. This oscillator generates a square wave signal that drives a high voltage switching transistor, such as the TIP47, which is capable of handling high voltage and current levels.
The design incorporates a 10 mH inductor, which is crucial for energy storage and transfer in the SMPS. The inductor must have a low DC resistance, ideally around 1.5 ohms, to ensure efficient operation and minimize power losses. The circuit also includes a driver transistor (2N3053) that amplifies the control signals to drive the high voltage transistor effectively.
To protect the circuit from excessive voltage, a 22K resistor is placed across the output. This resistor serves as a load, limiting the voltage to approximately 120 volts DC when the phone ringer is disconnected and around 90 volts DC when connected. The output voltage can be fine-tuned by adjusting a 150K resistor located between pins 10 and 11 of the oscillator circuit. This adjustment alters the frequency of the oscillator, which is typically around 800 Hz, a frequency suitable for telephone ringing.
The circuit is designed to produce a ringing signal for a duration of about 2 seconds, followed by a pause of approximately one minute between rings. This timing is controlled by a second Schmitt Trigger oscillator connected to pins 12 and 13. The timing intervals can be modified by changing the values of the 10K and 300K resistors connected to pin 12, allowing for customization of the ringing pattern based on user requirements.
In summary, this telephone ring generator circuit effectively combines various components and configurations to produce a reliable high voltage ringing signal, ensuring compatibility with standard telephone systems while allowing for adjustments in both output voltage and ringing duration.The telephone ring generator shown below generates the needed high voltage from a simple switching mode power supply (SMPS) which employs a CMOS Schmitt Trigger square wave oscillator, 10 mH inductor, high voltage switching transistor (TIP47 or other high voltage, 1 amp transistor) and a driver transistor (2N3053). The inductor should have a low DC resistance of 1.5 ohms or less. The switching supply must have a load connected to prevent the voltage from rising too high, so a 22K resistor is used across the output which limits the voltage to about 120 DC with the phone ringer disconnected and about 90 volts DC connected.
The output voltage can be adjusted by changing the value of the 150K resistor between pins 10 and 11 which will alter the oscillator frequency (frequency is around 800 Hz as shown). The supply is gated on and off by a second Schmitt Trigger oscillator (pins 12/13) so that the phone rings for about 2 seconds and then the circuit idles for about a minute between rings.
These times can be adjusted with the 10K and 300K resistors connected to pin 12.
simple common emitter amplifier
The biasing calculations for collector feedback common emitter amplifiers had not been previously addressed, particularly for a simple one-transistor NPN preamplifier built by Dino. Confusion arose regarding the role of resistor R1 in the schematic, which appeared to serve only...
Telephone ringer piezoelectric
The electronic bell operates without a power supply. Most resistors in the circuit are not critical, although capacitor C2 and resistors R2 and R3 perform optimally at the specified values. Omitting resistor R1 will increase the volume of the ringing...
voltage transistor loop to limit the current
The second transistor (T2) is activated by the current passing through the resistor (R1). When a DALI slave unit is connected, this current matches the current flowing through the power transistor (T1). The resistor's value is selected so that when...
wonky wire
The Wonky Wire circuit is based on the same oscillator used for the Flashing LED Lights. The timing components (R1/C1 and R4/C2) are significantly smaller, resulting in a higher oscillation frequency of approximately 3 kHz (3000 cycles per second). A...
Two transistor siren
The circuit diagram illustrates a simple two-transistor alarm circuit powered by a 9V PP3 battery. In this configuration, the two transistors are arranged to create an oscillator. The frequency of the oscillator increases when switch S2 is pressed and decreases...
Simple preamplifier circuits by transistors
When there is a need to amplify audio signals from various sources before they reach a custom amplifier, a preamplifier (or preamp) is typically employed. This document suggests a specific circuit that is interesting due to its use of a...
Telephone or extension tone ringer
This circuit utilizes ML8204/ML8205 devices. The components illustrated result in an output frequency that oscillates between 512 Hz (fin) and 640 Hz (fb) at a modulation rate of 10 Hz (t).
The circuit employing ML8204/ML8205 devices is designed for frequency modulation...
Full on transistor/fet curve tracer
The project involves adapting a curve tracer schematic, likely based on Metzger's circuit from the early 1970s, to integrate an ADC capture system and output the data to a 320x256 ELD panel. Additionally, a serial output will be included to...
Portable 230V lamp flasher circuit diagram
Portable 230V lamp flasher circuit diagram. The circuit is entirely transistorized and powered by a battery. A free-running oscillator circuit is implemented using two low-power, low-noise transistors, T1 and T2. One of these transistors remains in a conducting state while...