switching loads with MOSFETs
#MOSFET
#switching
#RDS_on
#reverse voltage
#parasitic inductance
#heatbed
#hotend heater
#transistor protection
#power electronics
Description: The primary concern is that the RDS_on of the utilized MOSFETs, when driven with a 5V gate voltage, is excessively low. Additionally, the reverse voltage that occurs when the MOSFET transitions from the on to the off state can damage the transistor. This reverse voltage is attributed to the parasitic series inductance of the heat bed, hotend heater cartridge, or resistor. This article aims to enhance understanding of these phenomena.
Thermal power loss of the MOSFET device can be calculated as follows: 12.5A² * 40mΩ = 6.25W. The theoretical resulting device case temperature is 6.25W * 80 °K/W + 25 °C (ambient temperature) = 525 °C. This extreme temperature will certainly destroy the MOSFET. To prevent this, a heat spreader with at least 15 °K/W is recommended, which would yield a device temperature of approximately 120 °C at room temperature.
In a different scenario, the thermal power loss of the MOSFET device can also be calculated as 12.5A² * 10mΩ = 1.6W. The theoretical resulting device case temperature in this case is 1.6W * 40 °K/W + 25 °C (ambient temperature) = 90 °C.
The two diagrams in the top left illustrate a single switching sequence from the heat bed being off to on and back off. The leftmost diagram shows the voltage, while the adjacent diagram displays the drain current. It is evident that the highest voltages occur during the transition from the on state to the off state. The subsequent diagrams provide a zoomed-in view of the drain-source voltage (Vds) during this event. Notably, in the top rightmost diagram, a voltage of approximately 250V occurs at the drain of the IRF7936, which is rated for only 30V Vds. Although this overvoltage lasts only 100ns and may not immediately damage the device, prolonged exposure to such overvoltage can lead to device malfunction.
The leftmost three diagrams in the second row depict the Vds voltage for the PSMN7R0-60YS MOSFET used on RUMBA in various applications: heated bed, hotend with a 40W heater cartridge, and hotend with a Vishay heater resistor. The Vds voltage is approximately 68V, while the MOSFET (PSMN7R0-60YS) is rated only for 60V, indicating that it is also operating outside of its specifications. This situation is likely to cause eventual board malfunction.
The circuit's favorable performance can be attributed to the inclusion of a freewheeling diode across the load (heat bed, hotend), which mitigates voltage overshoot. The schematic provided illustrates this simple circuit modification. It is crucial to check the RDS_on at Vgs=5V, as most devices are rated at Vgs=10V, leading to a significant difference in terms of RDS_on, which is considerably higher at Vgs=10V compared to 5V.
Utilizing a freewheeling diode across the load is essential, and the specifications for this diode are not particularly stringent. The current through this diode is less than 5A for approximately 0.5ms. A standard 1N4001 diode can suffice, as it can handle a forward current of 30A when the pulse duration is below 8ms.
In this application, the Vgs voltage is applied to the gate of the MOSFET, referenced to the source pin, which is connected to ground. The control voltage is sourced from the microcontroller output. Vds represents the voltage measured between the drain and source of the MOSFET, and it must not exceed the specified limit outlined in the datasheet. Typical voltage ratings for MOSFETs used in hotend and heatbed applications range between 20V and 60V.The biggest issue is that the RDS_on of the used MOSFETS is, driven with 5V gate voltage, too low. The other issue is that the the reverse voltage that occurs, when the MOSFET switches from on to off state kills the transistor. This revese voltage is caused by the parasitic series inductance of the heatbed, hotend heater cartride or resistor.
This article tries to generate understanding of what is happening. -> Thermal power loss of the MOSFET device: 12. 5A ² * 40mOhm = 6. 25W -> Theoretical resulting device case temperature 6. 25W * 80 °K/W + 25 °C (ambient temp. ) = 525 °C This definitely kills the MOSFET to survive add a heat spreader with at least 15 °K/W which results in a device temperature of approx. 120 °C at room temperature. -> Thermal power loss of the MOSFET device 12. 5A ² * 10mOhm = 1. 6W -> Theoretical resulting device case temperature 1. 6W * 40 °K/W + 25 °C (ambient temp. ) = 90 °C The two diagrams on the top left shows a single switching sequence from heatbed off - on - off The leftmost shows the voltage, the picture next to this the Drain current.
You can see that the highest voltages occur when switching from on state to off state. All other pictures show a zoomed view of the drain-source voltage (Vds) at this event. You can see that in the top rightmost diagram a voltage of approx. 250V(!) volts occures at the drain of the IRF7936. The device is rated only with 30V Vds. This voltage applys only 100ns and will not kill the device instantaneous but over time this overvoltage will lead to malfunction of the device. The leftmost three diagrams in the second row show the Vds voltage for the PSMN7R0-60YS MOSFET used on RUMBA in different applications: Heated bed, Hotend with 40W heater cartrige and Hotend with Vishay heater resistor.
As you can see the Vds voltage is approx. 68V. The MOSFET device (PSMN7R0-60YS) is only rated at 60V. This is also out of the specification of the device. Sooner or later it will result in malfunction of the board. What is the reason for this excellent behaviour The circuit is using a freewheeling diode across the load (heatbed, hotend) which prevents the voltage overshoot. The schematics below shows the (simple) circuit change. Always look for the RDS_on @ Vgs=5V most Devices are specified at Vgs=10V this makes a big difference in terms of RDS_on which is in this case (Vgs=10V) significantly higer at 5V Vgs.
Use a freewheeling diode across the load. The requirements on that diode are not very high. The current through this diode is < 5A for approx. 0. 5ms. For example a simple 1N4001 diode can make the job. Its allowed forward currend is 30A(!) when the pulse time is below 8ms. Vgs voltage applied to the gate of the MOSFET referenced to the source pin. In our application the source pin is tied to GND(ground). This is the control vopltage coming from the µController output Vds is the votage measured between drain and source of the MOSFET. This voltage must not be higher than specified in the datasheet. Typical values for MOSFETs used for hotend and heatbed are between 20. 60V
Thermal power loss of the MOSFET device can be calculated as follows: 12.5A² * 40mΩ = 6.25W. The theoretical resulting device case temperature is 6.25W * 80 °K/W + 25 °C (ambient temperature) = 525 °C. This extreme temperature will certainly destroy the MOSFET. To prevent this, a heat spreader with at least 15 °K/W is recommended, which would yield a device temperature of approximately 120 °C at room temperature.
In a different scenario, the thermal power loss of the MOSFET device can also be calculated as 12.5A² * 10mΩ = 1.6W. The theoretical resulting device case temperature in this case is 1.6W * 40 °K/W + 25 °C (ambient temperature) = 90 °C.
The two diagrams in the top left illustrate a single switching sequence from the heat bed being off to on and back off. The leftmost diagram shows the voltage, while the adjacent diagram displays the drain current. It is evident that the highest voltages occur during the transition from the on state to the off state. The subsequent diagrams provide a zoomed-in view of the drain-source voltage (Vds) during this event. Notably, in the top rightmost diagram, a voltage of approximately 250V occurs at the drain of the IRF7936, which is rated for only 30V Vds. Although this overvoltage lasts only 100ns and may not immediately damage the device, prolonged exposure to such overvoltage can lead to device malfunction.
The leftmost three diagrams in the second row depict the Vds voltage for the PSMN7R0-60YS MOSFET used on RUMBA in various applications: heated bed, hotend with a 40W heater cartridge, and hotend with a Vishay heater resistor. The Vds voltage is approximately 68V, while the MOSFET (PSMN7R0-60YS) is rated only for 60V, indicating that it is also operating outside of its specifications. This situation is likely to cause eventual board malfunction.
The circuit's favorable performance can be attributed to the inclusion of a freewheeling diode across the load (heat bed, hotend), which mitigates voltage overshoot. The schematic provided illustrates this simple circuit modification. It is crucial to check the RDS_on at Vgs=5V, as most devices are rated at Vgs=10V, leading to a significant difference in terms of RDS_on, which is considerably higher at Vgs=10V compared to 5V.
Utilizing a freewheeling diode across the load is essential, and the specifications for this diode are not particularly stringent. The current through this diode is less than 5A for approximately 0.5ms. A standard 1N4001 diode can suffice, as it can handle a forward current of 30A when the pulse duration is below 8ms.
In this application, the Vgs voltage is applied to the gate of the MOSFET, referenced to the source pin, which is connected to ground. The control voltage is sourced from the microcontroller output. Vds represents the voltage measured between the drain and source of the MOSFET, and it must not exceed the specified limit outlined in the datasheet. Typical voltage ratings for MOSFETs used in hotend and heatbed applications range between 20V and 60V.The biggest issue is that the RDS_on of the used MOSFETS is, driven with 5V gate voltage, too low. The other issue is that the the reverse voltage that occurs, when the MOSFET switches from on to off state kills the transistor. This revese voltage is caused by the parasitic series inductance of the heatbed, hotend heater cartride or resistor.
This article tries to generate understanding of what is happening. -> Thermal power loss of the MOSFET device: 12. 5A ² * 40mOhm = 6. 25W -> Theoretical resulting device case temperature 6. 25W * 80 °K/W + 25 °C (ambient temp. ) = 525 °C This definitely kills the MOSFET to survive add a heat spreader with at least 15 °K/W which results in a device temperature of approx. 120 °C at room temperature. -> Thermal power loss of the MOSFET device 12. 5A ² * 10mOhm = 1. 6W -> Theoretical resulting device case temperature 1. 6W * 40 °K/W + 25 °C (ambient temp. ) = 90 °C The two diagrams on the top left shows a single switching sequence from heatbed off - on - off The leftmost shows the voltage, the picture next to this the Drain current.
You can see that the highest voltages occur when switching from on state to off state. All other pictures show a zoomed view of the drain-source voltage (Vds) at this event. You can see that in the top rightmost diagram a voltage of approx. 250V(!) volts occures at the drain of the IRF7936. The device is rated only with 30V Vds. This voltage applys only 100ns and will not kill the device instantaneous but over time this overvoltage will lead to malfunction of the device. The leftmost three diagrams in the second row show the Vds voltage for the PSMN7R0-60YS MOSFET used on RUMBA in different applications: Heated bed, Hotend with 40W heater cartrige and Hotend with Vishay heater resistor.
As you can see the Vds voltage is approx. 68V. The MOSFET device (PSMN7R0-60YS) is only rated at 60V. This is also out of the specification of the device. Sooner or later it will result in malfunction of the board. What is the reason for this excellent behaviour The circuit is using a freewheeling diode across the load (heatbed, hotend) which prevents the voltage overshoot. The schematics below shows the (simple) circuit change. Always look for the RDS_on @ Vgs=5V most Devices are specified at Vgs=10V this makes a big difference in terms of RDS_on which is in this case (Vgs=10V) significantly higer at 5V Vgs.
Use a freewheeling diode across the load. The requirements on that diode are not very high. The current through this diode is < 5A for approx. 0. 5ms. For example a simple 1N4001 diode can make the job. Its allowed forward currend is 30A(!) when the pulse time is below 8ms. Vgs voltage applied to the gate of the MOSFET referenced to the source pin. In our application the source pin is tied to GND(ground). This is the control vopltage coming from the µController output Vds is the votage measured between drain and source of the MOSFET. This voltage must not be higher than specified in the datasheet. Typical values for MOSFETs used for hotend and heatbed are between 20. 60V
100Khz-multiple-output-switching-power-supply
The power supply employs two VN4000A 400-V MOSPOWER FETs configured in a half-bridge arrangement. It provides outputs of +5 V at 20 A and ±15 V (or ±12 V) at 1 A. The low-current outputs utilize linear three-terminal regulators, allowing...
motor-control-microcontrollers-miscellaneous
If an application utilizes a MOSFET to switch a load, it is straightforward to incorporate short-circuit or overload protection. This can be achieved by leveraging the internal resistance RDS(ON), which generates a voltage drop proportional to the current flowing through...
Power MOSFET Bridge Rectifier
The losses in a bridge rectifier can become significant when rectifying low voltages. The voltage drop across the bridge is approximately 1.5 V, which constitutes about 25% loss with an input voltage of 6V. This loss can be reduced by...
Mosfet amplifier schematic 25 Watt
Can be directly connected to CD players, tuners and tape recorders. Simply add a 10K Log potentiometer (dual gang for stereo) and a switch to cope with the various sources you need. Q6 & Q7 must have a small U-shaped...
Output by the CS3843 and CS5101 composed of 5V 3.3V switching DC power supply circuit
The CS3843 and CS5101 are components of a 5V/3.3V switching DC power supply circuit. The CS3843 is a fixed frequency PWM controller characterized by a set oscillator that precisely controls the duty cycle. It features a temperature-compensated reference voltage, a...
Mosfet stabilized power supply
One very important part of a tube amplifier is the power supply. It is crucial for the quality of the whole system. Especially beginners encounter problems like hum or drift that can become quite annoying. But rescue is ahead: the...
BROADBAND MULTI-OCTAVE HIGH POWER AMPLIFIER
A MOSFET solid-state kilowatt amplifier using MOSFETs. Helge's work was followed by articles that appeared in QEX and QST by Joel F. Paladino, N6AMG. Since then, very little has been written in amateur radio publications concerning MOSFETs in kilowatt applications....
300 Watt MOSFET Broadband Amplifier Using MRF141G
The following segment provides the enhanced Motorola schematic for a typical application of the MRF141G, which includes parasitic stabilization features. The MRF141G is a broadband power RF MOSFET capable of delivering a conservatively rated 300 watts across the FM broadcast...
25 Watt MosFet Amplifier
High Quality simple design No need for a preamplifier Can be directly connected to CD players, tuners and tape recorders. Simply add a 10K Log potentiometer (dual gang for stereo) and a switch to cope with the various sources you...