Current sensing relay
Description: It operates by PWM (Pulse Width Modulation) - well, actually by PFM - Pulse Frequency Modulation. At power up, C1 charges up via D1 and R1. R2 will conduct, pulling the base of the emitter follower, Tr2, up and feeding gate voltage to the MOSFET, Tr4. Clearly the circuits in an analogue region during power-up, but as this is intended for use on a high voltage supply, power-up is pretty quick. As Tr4 conducts, current is fed through R5 and the coil of the solenoid. The current builds up until the voltage across R5 becomes high enough to turn on Tr1. Tr1 and Tr3 are a complementary feedback pair, so when Tr1 conducts, they turn each other on in a snap action switch and the MOSFET gate gets turned hard off. The current in the solenoid coil is forced (by the inductance) to keep flowing. It does so via D3 and R4. But the current into Tr1's base is the sum of the currents through R4 and Tr3. R2's current flows through Tr1, so none flows in Tr2, so Tr3 current (after the base has discharged) is only the current through R3. So the current through R5 must drop by this amount before it is insufficient to keep Tr1 conducting. This current is caused by the sensed relay current flowing through R5, so the ratio of R3 to R4 sets the hysteresis. When there is insufficient current to keep Tr1 conducting, it turns off and the gate is again pulled high by R5 and Tr2, turning the MOSFET on. It slams the supply voltage across the relay coil, building up the current. Clearly the rate of current build-up will depend on the supply voltage, so at low voltages, the MOSFET turns on for a longer time and at high voltages, a shorter time. The time during which the MOSFET is off is dependent on the relay coil and is constant, whilst the on time varies, altering the frequency.
R5 needs to be chosen so that the required current is sensed. It should drop one Vbe (about 0.6V) at the required current. The MOSFET needs to be chosen with adequate voltage and current handling capacity, and of course, a heatsink may be required for the MOSFET. D3 should be a high-speed diode, with a voltage rating at least equal to the highest operating voltage the circuit will encounter. These parameters are all operating condition related. The circuit, in production, proved to be very reliable. Voltage spikes and current ratings need to be monitored. It is advisable not to operate it at low voltages, less than the solenoid voltage plus 15V, as the MOSFET goes into linear mode. This is not immediately damaging to the MOSFET, but it can generate excessive heat. Therefore, it is preferable to control the relay by activating and deactivating the controller rather than connecting and disconnecting the power. Methods for implementing this control could be developed in the future.It operates by PWM (Pulse Width Modulation) - well, actually by PFM - Pulse Frequency Modulation. At power up, C1 charges up via D1 and R1. R2 will conduct, pulling the base of the emitter follower, Tr2, up and feeding gate voltage to the MOSFET. Tr4. Clearly the circuits in an analogue region during power-up, but as this is intended for use on a high voltage supply, power-up is pretty quick.
As Tr4 conducts, current is fed through R5 and the coil of the Solenoid. The current builds up, until the voltage across R5 becomes high enough to turn on Tr1. Tr1 and Tr3 are a complementary feedback pair, so when Tr1 conducts, they turn each other on in a snap action switch and the MOSFET gate gets turned hard off. The current in the solenoid coil is forced (by the inductance) to keep flowing. It does so via D3 and R4. But the current into Tr1's base is the sum of the currents through R4 and Tr3. R2's current flows through Tr1, so none flows in Tr2, so Tr3 current (after the bate has discharged) is only the current through R3.
So the current through R5 must drop by this amount before it is insufficient to keep Tr1 conducting. This current is caused by the sensed relay current flowing through R5, so the ratio of R3 to R4 sets the hysteresis. When there is insufficient current to keep Tr1 conducting, it turns off and the gate is again pulled high by R5 and Tr2, turning the MOSFET on.
It slams the supply voltage across the relay coil, building up the current. Clearly the rate of current build-up will depend on the supply voltage, so at low voltages, the MOSFET turns on for a longer time and at high voltages, a shorter time. The time during which the MOSFET is off is dependant on the relay coil and is constant, whilst the on time varies, altering the frequency.
R5 needs to be chosen so that the required current is sensed. It should drop one Vbe (about 0.6v) at the required current. The MOSFET needs to be chosen with adequate voltage and current handling capacity, and of course you may need to heatsink the MOSFET. D3 should be a high speed diode, with a voltage rating at least equal to the highest operating voltage the circuit will encounter.
These things are all operating condition related, so I'll have to leave them to you! Constraints The circuit, in production, proved to be very reliable. Clearly you need to watch voltage spikes and current ratings. You should also not try to operate it at low voltages, say less that the solenoid voltage plus 15v, as the MOSFET goes into linear mode. This is not immediately damaging to the MOSFET, but it can get hot. For this reason, it is probably best not to switch the relay by connecting and disconnecting the power, but by activating and deactivating the controller.
Methods of doing this could be added later.
R5 needs to be chosen so that the required current is sensed. It should drop one Vbe (about 0.6V) at the required current. The MOSFET needs to be chosen with adequate voltage and current handling capacity, and of course, a heatsink may be required for the MOSFET. D3 should be a high-speed diode, with a voltage rating at least equal to the highest operating voltage the circuit will encounter. These parameters are all operating condition related. The circuit, in production, proved to be very reliable. Voltage spikes and current ratings need to be monitored. It is advisable not to operate it at low voltages, less than the solenoid voltage plus 15V, as the MOSFET goes into linear mode. This is not immediately damaging to the MOSFET, but it can generate excessive heat. Therefore, it is preferable to control the relay by activating and deactivating the controller rather than connecting and disconnecting the power. Methods for implementing this control could be developed in the future.It operates by PWM (Pulse Width Modulation) - well, actually by PFM - Pulse Frequency Modulation. At power up, C1 charges up via D1 and R1. R2 will conduct, pulling the base of the emitter follower, Tr2, up and feeding gate voltage to the MOSFET. Tr4. Clearly the circuits in an analogue region during power-up, but as this is intended for use on a high voltage supply, power-up is pretty quick.
As Tr4 conducts, current is fed through R5 and the coil of the Solenoid. The current builds up, until the voltage across R5 becomes high enough to turn on Tr1. Tr1 and Tr3 are a complementary feedback pair, so when Tr1 conducts, they turn each other on in a snap action switch and the MOSFET gate gets turned hard off. The current in the solenoid coil is forced (by the inductance) to keep flowing. It does so via D3 and R4. But the current into Tr1's base is the sum of the currents through R4 and Tr3. R2's current flows through Tr1, so none flows in Tr2, so Tr3 current (after the bate has discharged) is only the current through R3.
So the current through R5 must drop by this amount before it is insufficient to keep Tr1 conducting. This current is caused by the sensed relay current flowing through R5, so the ratio of R3 to R4 sets the hysteresis. When there is insufficient current to keep Tr1 conducting, it turns off and the gate is again pulled high by R5 and Tr2, turning the MOSFET on.
It slams the supply voltage across the relay coil, building up the current. Clearly the rate of current build-up will depend on the supply voltage, so at low voltages, the MOSFET turns on for a longer time and at high voltages, a shorter time. The time during which the MOSFET is off is dependant on the relay coil and is constant, whilst the on time varies, altering the frequency.
R5 needs to be chosen so that the required current is sensed. It should drop one Vbe (about 0.6v) at the required current. The MOSFET needs to be chosen with adequate voltage and current handling capacity, and of course you may need to heatsink the MOSFET. D3 should be a high speed diode, with a voltage rating at least equal to the highest operating voltage the circuit will encounter.
These things are all operating condition related, so I'll have to leave them to you! Constraints The circuit, in production, proved to be very reliable. Clearly you need to watch voltage spikes and current ratings. You should also not try to operate it at low voltages, say less that the solenoid voltage plus 15v, as the MOSFET goes into linear mode. This is not immediately damaging to the MOSFET, but it can get hot. For this reason, it is probably best not to switch the relay by connecting and disconnecting the power, but by activating and deactivating the controller.
Methods of doing this could be added later.
PWM DC Motor Speed Control
This is a circuit for controlling the speed of small DC motors; it works nicely as a speed controller for an HO or N gauge model railroad. More: The left half of the 556 dual timer IC is used as...
measurement Measuring large differential voltage
A high voltage power supply is designed for an electron beam system. The voltage regulator utilizes an outdated analog system that operates through a comparator and a reference signal from a potentiometer (POT). The challenge involves the feedback voltage from...
a single transistor smart battery charger
The electronic design features a smart battery charger schematic that utilizes only a single transistor. This design is notable as similar circuits typically employ simple integrated circuits. When the battery's charge level falls below a specific threshold voltage, the circuit...
PWM DC Motor Speed Control
This is a circuit for controlling the speed of small DC motors; it works nicely as a speed controller for an HO or N gauge model railroad. More: The left half of the 556 dual timer IC is used as...
transistor as a switch circuit problems
A circuit is being designed that incorporates two key switches, which must both be closed for current to flow through the circuit.
The proposed circuit configuration employs two key switches connected in series. In this arrangement, the current can only pass...
DIY Homemade Kirlian Photographs
Instructions for constructing a simple Kirlian effect camera to capture high voltage corona discharges around objects, also referred to as aura photography.
The Kirlian effect is a phenomenon where high voltage electrical discharges create a visual representation of the energy field...
High Voltage Inverter
This is a simple high-voltage inverter circuit. It uses an NPN transistor type 2N3055. This circuit is designed to invert low voltage to high voltage.
The high-voltage inverter circuit utilizing the 2N3055 NPN transistor serves as an effective means to convert...
8-Channel High-Current Opto-Isolated Open-drain MOSFET Driver motor Board
The embedded I/O board offers isolated high voltage switch inputs and eight high current, high voltage DC outputs. It utilizes optically isolated, open drain N-MOSFET transistors functioning as solid state relays (SSR) to control various resistive or inductive loads. These...
Transistor Circuits
This page presents several transistor circuits that are not commonly found on other pages due to the absence of a specific topic. These circuits, however, illustrate particular points but lack detailed descriptions. An example of an RF amplifier circuit using...