Optical Heart Rate Monitor
#heart rate monitor
#IR LED
#phototransistor
#light sensor
#24 bit ADC
#signal conditioning
#medical electronics
#waveform analysis
#USB DAQ
#dynamic range
Description: This application note describes the creation of a heart rate monitor utilizing an infrared (IR) LED and a phototransistor pair, with the waveform observed at the output of the phototransistor. The purpose of this project is to demonstrate a typical light sensor application rather than for actual medical use. An accompanying video illustrates the low-level signals involved in this circuit and how the dynamic range of a 24-bit ADC EMANT300 USB DAQ enables the observation of these signals without additional signal conditioning. When a finger is placed on the phototransistor, the voltage reading increases above 0.3V. With good contact, a sinusoidal signal is observed, superimposed on a fluctuating DC signal, resulting in a simple differential signal. Mathematically, it is known that the differential value is zero at the maximum or minimum points. An autocorrelation function is then applied to extract the peaks and calculate the heart rate. If the signal is noisy, incorrect BPM readings may occur, which are disregarded. This process is managed by the HRM class, written in C#, which can be enhanced using Visual C# 2005 Express. The figure below displays the filtered waveform observed at the phototransistor, with the waveform being processed through software averaging.
The heart rate monitor circuit employs an infrared LED and a phototransistor to detect variations in light intensity caused by blood flow in a fingertip. The IR LED emits infrared light, which penetrates the skin and reflects back to the phototransistor. The amount of light received by the phototransistor varies with the pulsation of blood, leading to changes in the output voltage.
The circuit is designed to amplify and filter the weak signals generated by the phototransistor. The output is connected to a 24-bit ADC, specifically the EMANT300 USB DAQ, which is capable of capturing low-level signals with high precision. This allows for effective digitization of the analog signal without the need for extensive external signal conditioning.
The software component of the heart rate monitor includes a class written in C#, which is responsible for processing the data collected from the ADC. The class implements algorithms for noise reduction and peak detection. It utilizes an autocorrelation function to identify the periodic peaks in the signal corresponding to heartbeats. The peaks are analyzed to compute the beats per minute (BPM) value. Any readings that deviate significantly from expected values due to noise or interference are filtered out to ensure accuracy.
The output waveform, as depicted in the accompanying figure, is subjected to software-based averaging to enhance signal clarity. This filtering process helps in minimizing the impact of noise, allowing for a more reliable heart rate measurement. Overall, the design illustrates a practical application of light sensors in biomedical monitoring, showcasing the integration of hardware and software in developing a functional heart rate monitoring system.In this application note, we create a heart rate monitor by using one IR LED and phototransistor pair and observing the waveform at the phototransistor output. This is intended for illustrating a typical light sensor application and not intended for actual medical use.
The accompanying video also shows the typical low level signals involved in this type of circuit and how the dynamic range from a 24 bit ADC EMANT300 USB DAQ allows such signals to be observed without further signal conditioning. When a finger is placed on the phototransistor, the voltage read rises above 0.3V. If a good contact is made, a sinusoidal type signal is observed. As the signal rides on a fluctuating DC signal, a simple differential signal is created. From maths, we know that when a max or min is reached, its differential value is zero. After this an autocorrelation function is applied and the peaks extracted to obtain the heart rate. When the signal is noisy, a wrong BPM will be calculated. Any count that is obviously wrong is ignored. This is all taken care of by the HRM class. The HRM class is written in C#. You can improve on it using the Visual C# 2005 Express. The figure below shows the filtered waveform seen at the phototransistor. The waveform is filtered by software using averaging.
The heart rate monitor circuit employs an infrared LED and a phototransistor to detect variations in light intensity caused by blood flow in a fingertip. The IR LED emits infrared light, which penetrates the skin and reflects back to the phototransistor. The amount of light received by the phototransistor varies with the pulsation of blood, leading to changes in the output voltage.
The circuit is designed to amplify and filter the weak signals generated by the phototransistor. The output is connected to a 24-bit ADC, specifically the EMANT300 USB DAQ, which is capable of capturing low-level signals with high precision. This allows for effective digitization of the analog signal without the need for extensive external signal conditioning.
The software component of the heart rate monitor includes a class written in C#, which is responsible for processing the data collected from the ADC. The class implements algorithms for noise reduction and peak detection. It utilizes an autocorrelation function to identify the periodic peaks in the signal corresponding to heartbeats. The peaks are analyzed to compute the beats per minute (BPM) value. Any readings that deviate significantly from expected values due to noise or interference are filtered out to ensure accuracy.
The output waveform, as depicted in the accompanying figure, is subjected to software-based averaging to enhance signal clarity. This filtering process helps in minimizing the impact of noise, allowing for a more reliable heart rate measurement. Overall, the design illustrates a practical application of light sensors in biomedical monitoring, showcasing the integration of hardware and software in developing a functional heart rate monitoring system.In this application note, we create a heart rate monitor by using one IR LED and phototransistor pair and observing the waveform at the phototransistor output. This is intended for illustrating a typical light sensor application and not intended for actual medical use.
The accompanying video also shows the typical low level signals involved in this type of circuit and how the dynamic range from a 24 bit ADC EMANT300 USB DAQ allows such signals to be observed without further signal conditioning. When a finger is placed on the phototransistor, the voltage read rises above 0.3V. If a good contact is made, a sinusoidal type signal is observed. As the signal rides on a fluctuating DC signal, a simple differential signal is created. From maths, we know that when a max or min is reached, its differential value is zero. After this an autocorrelation function is applied and the peaks extracted to obtain the heart rate. When the signal is noisy, a wrong BPM will be calculated. Any count that is obviously wrong is ignored. This is all taken care of by the HRM class. The HRM class is written in C#. You can improve on it using the Visual C# 2005 Express. The figure below shows the filtered waveform seen at the phototransistor. The waveform is filtered by software using averaging.
Signal-conditioner-with-bridge
The LT1007 is capable of providing excitation current directly to bias the 350-0 bridge at 5 V. With only 5 V across the bridge, as opposed to the usual 10 V, total power dissipation and bridge warm-up drift is reduced....
Light/Dark Detector relay
This handy little circuit can tell the difference between darkness and light, making it very useful for switching on and off signs, porch lights or other things when it gets dark or light. More: R1 Adjusts sensitivity
The circuit described is...
Light-sensitive Alarm Project
The circuit detects a sudden shadow on the light sensor and activates a bleeper when this occurs. It is designed to ignore gradual changes in brightness to prevent false alarms. The bleeper operates for a brief duration to conserve battery...
Protector
The circuits presented here will prevent turnouts from being thrown while a train is on a switch, which is ideal in situations where the switch cannot be seen by the operator. They utilize phototransistor sensors to detect the presence of...
Light/Dark Detector relay
This handy little circuit can tell the difference between darkness and light, making it very useful for switching on and off signs, porch lights or other things when it gets dark or light. More: R1 Adjusts sensitivity
The circuit described is...
Simple Light Sensor Circuit Features High Dynamic Range
Ambient light is increasingly being utilized as an energy source. To assist designers in developing such systems, this circuit effectively measures ambient light intensity across four decades of measurement. The design is cost-effective, and with the sensor housed in a...
6V Light Barrier Sensor Detector
The following circuit illustrates a Light Barrier Sensor Detector Circuit Diagram. Features include a single transistor, an adjustable potentiometer, and a 6V power supply.
The Light Barrier Sensor Detector Circuit is designed to detect the presence of an object by utilizing...
Photo Inverting
For phototransistors, a resistance value of 470K ohms is suitable for most ambient light conditions. In cases of dim lighting, a higher resistor value, such as 1 Megohm, can enhance sensitivity. This high-impedance test voltmeter circuit is also applicable for...
Light Sensor Circuit
An ambient light sensor circuit is a circuit that utilizes light intensity to perform various applications.
An ambient light sensor circuit typically consists of a light-dependent resistor (LDR) or phototransistor that detects the intensity of ambient light. The sensor converts the...