Light/dark relay switch
#LDR
#relay
#Darlington pair
#trimpot
#light detection
#dark detection
#switching circuit
#sensitivity adjustment
Description: This kit is the most basic, practical circuit to build using an LDR to turn on a relay. The two transistors connected as a Darlington pair give the circuit enough sensitivity, while the trimpot gives sensitivity adjustment. The switching point of the relay is dependent on the supply voltage and temperature. This circuit is satisfactory if the changes in light level to be detected are large and the transition is quick - for example, a person walking past a doorway. But an inherent problem of the circuit is chattering of the relay for slowly changing light levels just at the transition point between turning on/off and vice versa.
More: Look what happens when the relay turns on: the input voltage drops slightly (say around 20 mV) when the relay turns on and loads the circuit. If the voltage applied to the base-emitter junction of Q1 is only just sufficient to turn it on then this slight drop will immediately start to turn Q1 off. But then with the relay load reducing the supply voltage will start to rise & Q1 will start to turn on etc. This leads to the relay chattering as it rapidly turns on/off. (This problem is overcome in K79B by the built-in hysteresis of the op-amp, and the Schmidt Trigger arrangement of the circuit in K79C.)
This circuit utilizes a Light Dependent Resistor (LDR) as a light sensor, which changes its resistance based on the ambient light level. When the light intensity reaches a predetermined threshold, the LDR's resistance decreases, allowing current to flow through the circuit. The Darlington pair configuration, consisting of two transistors (Q1 and Q2), amplifies the current from the LDR, providing sufficient gain to drive the relay.
A trimpot is included in the design to allow for fine-tuning of the sensitivity of the circuit. By adjusting the resistance of the trimpot, the user can set the light level at which the relay will activate. This feature is particularly useful for applications that require specific light conditions for operation.
The relay serves as an output device that can control larger loads, such as lights or alarms, based on the detected light levels. However, a notable issue arises with the relay's operation when the light levels change slowly. The circuit may experience chattering, where the relay rapidly toggles between the on and off states due to slight fluctuations in the input voltage caused by the relay’s own load. This occurs because the small voltage drop across the relay when it activates can momentarily reduce the base-emitter voltage of Q1, causing it to turn off, which then allows the voltage to recover and turn Q1 back on again, creating an unstable condition.
To mitigate this chattering effect, alternative circuit designs, such as those found in K79B and K79C, implement hysteresis and Schmidt Trigger configurations. These designs introduce a degree of feedback that stabilizes the switching behavior of the circuit, ensuring that the relay operates reliably without unintended toggling during slow light transitions.This kit is the most basic, practical circuit to build using an LDR to turn on a relay. The two transistors connected as a Darlington pair give the circuit enough sensitivity, while the trimpot give sensitivity adjustment. The switching point of the relay is dependent on the supply voltage and temperature. This circuit is satisfactory if the changes in light level to be detected are large and the transition is quick - for example, a person walking past a doorway.
But an inherent problem of the circuit is chattering of the relay for slowly changing light levels just at the transistion point between turning on/odd and vice versa. Look what happens when the relay turns on: the input voltage drops slightly (say around 20 mV) when the relay turns on and loads the circuit. If the voltage applied to the base-emitter junction of Q1 is only just sufficient to turn it on then this slight drop will immediately start to turn Q1 off.
But then with the relay load reducing the supply voltage will start to rise & Q1 will start to turn on etc. This leads to the relay chattering as it rapidly turns on/off. (This problem is overcome in K79B by the built-in hysteresis of the op-amp, and the Schmidt Trigger arrangment of the circuit in K79C.)
More: Look what happens when the relay turns on: the input voltage drops slightly (say around 20 mV) when the relay turns on and loads the circuit. If the voltage applied to the base-emitter junction of Q1 is only just sufficient to turn it on then this slight drop will immediately start to turn Q1 off. But then with the relay load reducing the supply voltage will start to rise & Q1 will start to turn on etc. This leads to the relay chattering as it rapidly turns on/off. (This problem is overcome in K79B by the built-in hysteresis of the op-amp, and the Schmidt Trigger arrangement of the circuit in K79C.)
This circuit utilizes a Light Dependent Resistor (LDR) as a light sensor, which changes its resistance based on the ambient light level. When the light intensity reaches a predetermined threshold, the LDR's resistance decreases, allowing current to flow through the circuit. The Darlington pair configuration, consisting of two transistors (Q1 and Q2), amplifies the current from the LDR, providing sufficient gain to drive the relay.
A trimpot is included in the design to allow for fine-tuning of the sensitivity of the circuit. By adjusting the resistance of the trimpot, the user can set the light level at which the relay will activate. This feature is particularly useful for applications that require specific light conditions for operation.
The relay serves as an output device that can control larger loads, such as lights or alarms, based on the detected light levels. However, a notable issue arises with the relay's operation when the light levels change slowly. The circuit may experience chattering, where the relay rapidly toggles between the on and off states due to slight fluctuations in the input voltage caused by the relay’s own load. This occurs because the small voltage drop across the relay when it activates can momentarily reduce the base-emitter voltage of Q1, causing it to turn off, which then allows the voltage to recover and turn Q1 back on again, creating an unstable condition.
To mitigate this chattering effect, alternative circuit designs, such as those found in K79B and K79C, implement hysteresis and Schmidt Trigger configurations. These designs introduce a degree of feedback that stabilizes the switching behavior of the circuit, ensuring that the relay operates reliably without unintended toggling during slow light transitions.This kit is the most basic, practical circuit to build using an LDR to turn on a relay. The two transistors connected as a Darlington pair give the circuit enough sensitivity, while the trimpot give sensitivity adjustment. The switching point of the relay is dependent on the supply voltage and temperature. This circuit is satisfactory if the changes in light level to be detected are large and the transition is quick - for example, a person walking past a doorway.
But an inherent problem of the circuit is chattering of the relay for slowly changing light levels just at the transistion point between turning on/odd and vice versa. Look what happens when the relay turns on: the input voltage drops slightly (say around 20 mV) when the relay turns on and loads the circuit. If the voltage applied to the base-emitter junction of Q1 is only just sufficient to turn it on then this slight drop will immediately start to turn Q1 off.
But then with the relay load reducing the supply voltage will start to rise & Q1 will start to turn on etc. This leads to the relay chattering as it rapidly turns on/off. (This problem is overcome in K79B by the built-in hysteresis of the op-amp, and the Schmidt Trigger arrangment of the circuit in K79C.)
Relay pull-in timer circuit in time process
The circuit features a two-stage structure with a timing range of approximately 0.5 to 12 seconds, while in a specified configuration, the timing range extends from 1 to 160 seconds. The transformer parameters include an iron core made of M42/15.7...
Four reversing operation of the reverse brake circuit
The circuit depicted in Figure 3-131 utilizes a relay instead of a speed control relay. It is designed to operate effectively in dusty environments and other challenging conditions.
The circuit operates by employing a relay as a primary switching mechanism, which...
Reducing Relay Power Consumption
Relays are commonly utilized as electrically controlled switches. Unlike transistors, the switch contacts of relays are electrically isolated from the control input. However, the power dissipation in a relay coil can be undesirable for battery-operated applications. The incorporation of an...
Spitfire/GT6 Relay and Blinker Information
The Haynes manual is quite confusing regarding the labeling of relays on Spitfires. The two main sources of confusion are: 1. The illustrations depict right-hand drive cars with different relay locations, and 2. The naming of the relays is unusual,...
Time relay three-start circuit
The circuit depicted in Figure 3-159 employs complementary operation three times along with three relay contacts. This is followed by the automatic elimination of the rotor circuit resistance levels, ultimately reducing the rotor winding variable resistor to zero (fully shorted),...
Automatic Lawn Light with LDR
The circuit of a compact and true solid-state automatic lawn light is described here. The circuit can be used to switch on incandescent garden light bulbs.
The described circuit functions as an automatic control system for garden lighting, specifically designed for...
what relay should i use parallel port
Control a toy car. The toy car is operated via a wired controller, rather than being radio-controlled. The intention is to utilize relays to control the toy through a parallel port. There are various types and models of relays, and...
Lights-On Reminder Circuit
A relay and two diodes are all that is needed; the relay performs the job of a buzzer, so no annunciator is required. When the lights are left on while the ignition is off, the normally closed relay contacts are...
microcontroller 12V relay circuit converted to 5V relay under uC control
The BC547B transistor has a collector-base voltage (Vcbo) of 50V, a collector-emitter voltage (Vceo) of 45V, and an emitter-base voltage (Vebo) of 6V. In contrast, the BC548 transistor in the original circuit has a Vcbo of 30V, a Vceo of...