Light Controlled Relays
Description: The first circuit energizes the relay when the light rises above the preset level. The second circuit energizes the relay when the light falls below the preset level. The two circuits are practically identical. The only difference between them is the polarity of the transistor. The value of the LDR is not critical. The important thing is the voltage on pins 5 & 6. Any value LDR should work satisfactorily. But you may need to change the value of R1 to achieve the desired range of adjustment. More: Do not use the "on-board" relay to switch mains voltage. The board's layout does not offer sufficient isolation between the relay contacts and the low-voltage components. If you want to switch mains voltage - mount a suitably rated relay somewhere safe.
The described circuit consists of two light-sensitive relay control circuits, each utilizing a Light Dependent Resistor (LDR) to detect ambient light levels. The first circuit activates the relay when the light intensity exceeds a predetermined threshold, while the second circuit activates the relay when the light intensity drops below this threshold.
Both circuits are designed similarly, with the primary distinction being the orientation of the transistor used in each circuit. This bipolar junction transistor (BJT) configuration allows for the switching of the relay based on the light levels detected by the LDR. The LDR's resistance decreases with increasing light levels, which allows for the modulation of the voltage at the transistor's base, effectively controlling the relay's state.
The circuit operates by monitoring the voltage levels at pins 5 and 6, which are critical for determining the relay's activation state. The selection of the LDR is flexible, as any LDR can be used satisfactorily; however, the resistance value of R1 may need adjustment to fine-tune the sensitivity and range of the light detection. This adjustment will ensure that the circuit accurately responds to the specific light conditions required for the application.
It is crucial to note that the on-board relay should not be used for switching mains voltage due to insufficient isolation between the relay contacts and the low-voltage components on the board. For applications requiring mains voltage switching, it is recommended to use an appropriately rated relay mounted in a secure location, ensuring compliance with safety standards and preventing potential hazards associated with electrical isolation.The first circuit energizes the relay when the light rises above the preset level. The second circuit energizes the relay when the light falls below the preset level. The two circuits are practically identical. The only difference between them is the polarity of the transistor. The value of the LDR is not critical. The important thing is the voltage on pins 5 & 6. Any value LDR should work satisfactorily. But you may need to change the value of R1 - to achieve the desired range of adjustment. Do not use the "on-board" relay to switch mains voltage. The board's layout does not offer sufficient isolation between the relay contacts and the low-voltage components. If you want to switch mains voltage - mount a suitably rated relay somewhere safe -
The described circuit consists of two light-sensitive relay control circuits, each utilizing a Light Dependent Resistor (LDR) to detect ambient light levels. The first circuit activates the relay when the light intensity exceeds a predetermined threshold, while the second circuit activates the relay when the light intensity drops below this threshold.
Both circuits are designed similarly, with the primary distinction being the orientation of the transistor used in each circuit. This bipolar junction transistor (BJT) configuration allows for the switching of the relay based on the light levels detected by the LDR. The LDR's resistance decreases with increasing light levels, which allows for the modulation of the voltage at the transistor's base, effectively controlling the relay's state.
The circuit operates by monitoring the voltage levels at pins 5 and 6, which are critical for determining the relay's activation state. The selection of the LDR is flexible, as any LDR can be used satisfactorily; however, the resistance value of R1 may need adjustment to fine-tune the sensitivity and range of the light detection. This adjustment will ensure that the circuit accurately responds to the specific light conditions required for the application.
It is crucial to note that the on-board relay should not be used for switching mains voltage due to insufficient isolation between the relay contacts and the low-voltage components on the board. For applications requiring mains voltage switching, it is recommended to use an appropriately rated relay mounted in a secure location, ensuring compliance with safety standards and preventing potential hazards associated with electrical isolation.The first circuit energizes the relay when the light rises above the preset level. The second circuit energizes the relay when the light falls below the preset level. The two circuits are practically identical. The only difference between them is the polarity of the transistor. The value of the LDR is not critical. The important thing is the voltage on pins 5 & 6. Any value LDR should work satisfactorily. But you may need to change the value of R1 - to achieve the desired range of adjustment. Do not use the "on-board" relay to switch mains voltage. The board's layout does not offer sufficient isolation between the relay contacts and the low-voltage components. If you want to switch mains voltage - mount a suitably rated relay somewhere safe -
Automatic light dimmer circuit
This is an automatic light dimmer circuit. There is no need to manually adjust the brightness of the lights. This circuit is highly convenient, as it utilizes a light-dependent resistor (LDR) to detect external light levels.
The automatic light dimmer circuit...
One 2N2222 Transistor Code Lock
The circuit consists of a basic transistor switch with a relay connected at its collector as the load. This represents a straightforward electronic code lock circuit that employs a single transistor.
The circuit operates by utilizing a transistor as a switch...
Sun Light Chaser
With RFT illuminated, point R goes to 0 volt and LM runs. With LFT illuminated, point R goes to 0 volt and RM runs. With RFT and/or LFT not illuminated, points R/L go to +9 volt; P1 and P2 controls...
Window-detector
The detector circuit compares the output voltage of two separate voltage dividers with a fixed reference voltage. The resultant absolute error signal is amplified and converted to a logic signal that is TTL compatible.
The described detector circuit serves as a...
From power fluctuations of one single-junction transistor trigger circuit
Both circuits can synchronize trapezoidal wave voltage, which is converted into intermittent small rectangular pulses. Its working principle involves periodic operation in synchronization with the grid frequency of the zero-volt switching voltage of the DC chopper. Due to the low...
2 channel audio mixer circuit using transistors
This two-channel audio mixer utilizes 2N3904 transistors to create two preamplifiers. The first preamplifier is designed for high gain, suitable for microphone input, while the second preamplifier allows for control over the audio level input. The audio mixer requires a...
Transistor Sensor Temperature Measurer
Using the fact that the VRE of a transistor shifts 59.16 mV per decade of current at 25°C. This constant is 0.33%/°C. This V5E-vs.-current relationship holds true regardless of the FBe absolute value. IC, an LT1043, acts as an oscillator...
Power Control
The circuit presented utilizes a two-transistor "flasher" to generate triggering pulses, replacing the traditional unijunction transistor design. This configuration allows for a broad range of control with minimal hysteresis and sensitivity to line voltage. Two diodes rectify the line voltage,...
Time relay three-start circuit
The circuit depicted in Figure 3-159 employs complementary operation three times along with three relay contacts. This is followed by the automatic elimination of the rotor circuit resistance levels, ultimately reducing the rotor winding variable resistor to zero (fully shorted),...