Simple Infrared Control Extender
#infrared
#IR signal
#remote control extender
#photodiode
#consumer electronics
#TV
#VCR
#CD player
#DVD player
#signal transmission
Description: Many consumer electronic devices, such as televisions, VCRs, and CD/DVD players, utilize infrared remote controls. In certain situations, it is beneficial to enhance the control range. This circuit is designed to receive the infrared signal from a remote control and retransmit it, allowing control from a distance or around corners into different rooms. The circuit employs a photodiode.
More: The photodiode D4 is connected to the inverting input of a 741 operational amplifier (op-amp) through a resistor (R2) and a capacitor (C1). The BPW41 photodiode, sourced from Vishay/Telefunken, requires reverse biasing to convert light energy into an equivalent voltage; hence, it is also connected to the positive supply rail via resistor R1. The non-inverting input of the op-amp is maintained at half the supply voltage using two equal resistors, R3 and R4. Following the op-amp, a BD240 transistor is utilized as an after-burner, which can supply substantial current pulses to infrared LEDs D2 and D3. It is important to note that the pulsed current through the LD274 infrared emitters should not exceed approximately 100 mA, necessitating the inclusion of a fixed resistor in series with a preset resistor (P1). An additional visible-light LED (D1) is incorporated to flash when an infrared signal is detected from the remote control. Care should be taken when adjusting the setting of P1 to ensure that the current through the infrared emitters does not exceed the minimum required to effectively reach the intended destination of the infrared signal. The currents referenced are peak levels due to the low duty cycle of the infrared pulses; thus, the average current drawn from the battery will be significantly lower. The directivity of the infrared LEDs, and consequently the range of the control extender, can be enhanced by equipping the LEDs with reflective caps.
This circuit effectively extends the range of infrared remote controls by utilizing a photodiode for signal reception and an operational amplifier for signal amplification. The design includes provisions for current limiting and signal indication, ensuring reliable operation while maintaining efficiency. The use of reflective caps on the infrared LEDs can further optimize performance, allowing for greater control distances and improved signal directionality. The careful selection and configuration of components, including resistors and capacitors, contribute to the overall functionality and reliability of the circuit, making it suitable for various consumer electronic applications.Lots of consumer electronic equipment like TV sets, VCRs, CD and DVD players employs infrared remote control. In some cases, it is desirable to extend the range of the available control and this circuit fits the bill, receiving the IR signal from your remote control and re-transmitting it, for example, around a corner into another room.
Photodiode D4 is connected to the inverting input of a 741 opamp through resistor R2 and capacitor C1. Since the BPW41 photodiode (from Vishay/Telefunken) needs to be reverse-biased to turn light energy into a corresponding voltage, it is also connected to the positive supply rail via R1. The non-inverting input of the 741 is held at half the supply voltage by means of equal resistors R3 and R4.
The opamp is followed by a BD240 after-burner transistor capable of supplying quite high current pulses through IR LEDs D2 and D3. However, the pulsed current through the LD274s should not exceed 100 mA or so, hence a fixed resistor is used in series with preset P1.
D1 is an ordinary visible-light LED that flashes when an IR signal is received from the remote. With regard to the setting of P1, do not make the IRED current higher than necessary to reliably reach the final destination of the IR signal. Also, the currents mentioned above are peak levels due to the small duty factor of the IR pulses, the average current drawn from the battery will be much smaller.
The directivity of the IR LEDs and consequently the range of the control extender may be increased by fitting the devices with reflective caps.
More: The photodiode D4 is connected to the inverting input of a 741 operational amplifier (op-amp) through a resistor (R2) and a capacitor (C1). The BPW41 photodiode, sourced from Vishay/Telefunken, requires reverse biasing to convert light energy into an equivalent voltage; hence, it is also connected to the positive supply rail via resistor R1. The non-inverting input of the op-amp is maintained at half the supply voltage using two equal resistors, R3 and R4. Following the op-amp, a BD240 transistor is utilized as an after-burner, which can supply substantial current pulses to infrared LEDs D2 and D3. It is important to note that the pulsed current through the LD274 infrared emitters should not exceed approximately 100 mA, necessitating the inclusion of a fixed resistor in series with a preset resistor (P1). An additional visible-light LED (D1) is incorporated to flash when an infrared signal is detected from the remote control. Care should be taken when adjusting the setting of P1 to ensure that the current through the infrared emitters does not exceed the minimum required to effectively reach the intended destination of the infrared signal. The currents referenced are peak levels due to the low duty cycle of the infrared pulses; thus, the average current drawn from the battery will be significantly lower. The directivity of the infrared LEDs, and consequently the range of the control extender, can be enhanced by equipping the LEDs with reflective caps.
This circuit effectively extends the range of infrared remote controls by utilizing a photodiode for signal reception and an operational amplifier for signal amplification. The design includes provisions for current limiting and signal indication, ensuring reliable operation while maintaining efficiency. The use of reflective caps on the infrared LEDs can further optimize performance, allowing for greater control distances and improved signal directionality. The careful selection and configuration of components, including resistors and capacitors, contribute to the overall functionality and reliability of the circuit, making it suitable for various consumer electronic applications.Lots of consumer electronic equipment like TV sets, VCRs, CD and DVD players employs infrared remote control. In some cases, it is desirable to extend the range of the available control and this circuit fits the bill, receiving the IR signal from your remote control and re-transmitting it, for example, around a corner into another room.
Photodiode D4 is connected to the inverting input of a 741 opamp through resistor R2 and capacitor C1. Since the BPW41 photodiode (from Vishay/Telefunken) needs to be reverse-biased to turn light energy into a corresponding voltage, it is also connected to the positive supply rail via R1. The non-inverting input of the 741 is held at half the supply voltage by means of equal resistors R3 and R4.
The opamp is followed by a BD240 after-burner transistor capable of supplying quite high current pulses through IR LEDs D2 and D3. However, the pulsed current through the LD274s should not exceed 100 mA or so, hence a fixed resistor is used in series with preset P1.
D1 is an ordinary visible-light LED that flashes when an IR signal is received from the remote. With regard to the setting of P1, do not make the IRED current higher than necessary to reliably reach the final destination of the IR signal. Also, the currents mentioned above are peak levels due to the small duty factor of the IR pulses, the average current drawn from the battery will be much smaller.
The directivity of the IR LEDs and consequently the range of the control extender may be increased by fitting the devices with reflective caps.
Infrared approach detector / sensor
The basic operation of the monitor connected to the circuit is to detect objects (obstacles) at distances ranging from a few millimeters to several centimeters. This type of circuit is utilized in various industries and hospitals. The position sensor IC2...
Day and Night Infrared Detection
The following is a method to allow day and night detection using Infrared/Visible light sensitive phototransistors and a simple LM339 voltage comparator circuit. A phototransistor is mounted between the rails so that it is covered by the train as it...
Wireless Switch
The circuit described here operates without physical contact to control the appliance. It requires the user to move their hand between the infrared LED (IR LED1) and the phototransistor (T1). The infrared rays emitted by IR LED1 are detected by...
Simple Infrared Illuminator
An infrared illuminator emits light in the infrared spectrum and is widely used in night vision cameras to capture images in the dark, particularly in applications such as CCTV cameras.
Infrared illuminators are essential components in various surveillance and imaging systems,...
park aid schematics
IC1 operates as an oscillator that drives an infrared LED with pulses of 0.8 milliseconds at a frequency of 120 Hz, generating approximately 300 mA of peak current. Diodes D1 and D2 are aligned and positioned a few centimeters apart...
Lazer Tag Infrared Receivers
The individual was not inclined to create and program the timing controller for the PCB laser printer. They recalled having a laser tag gun that had been misaligned during a previous disassembly. The device in question is a Nerf (formerly...
Infrared Remote Receiver Has Four Outputs
This circuit allows any infrared (IR) remote control to manage the outputs of a 4017 decade counter. It utilizes a 3-terminal IR receiver (IRD1) to capture infrared signals from the transmitter. The output from IRD1 is connected to an NPN...
Selective Preamplifier For Infrared Photodiode Circuit
The circuit utilizes a tuned circuit for frequency selection, designed to operate at approximately 51 kHz. The 2N3565 transistor amplifies the output generated by the tuned circuit.
The described circuit operates on the principle of resonance, where the tuned circuit is...
Infrared intrusion barrier
The circuit diagram of an infrared intrusion detector is presented. This system triggers an alarm when a trespasser interrupts the invisible infrared beam. It consists of a receiver circuit and a transmitter circuit. The transmitter circuit utilizes two TLC555 integrated...