IR (infrared) receiver and transmitter
#infrared
#IR LED
#IR phototransistor
#receiver
#transmitter
#remote control
#signal transmission
#electronics
#DIY
Description: Recently, samples of IR LEDs and a corresponding IR phototransistor were acquired. A project was initiated to utilize these components.
The project involves the integration of infrared (IR) LEDs with an IR phototransistor to create a simple optical communication system or a basic IR sensor circuit. The IR LED emits infrared light, which is typically invisible to the human eye, while the phototransistor detects this emitted light, allowing for the conversion of light signals into electrical signals.
In this circuit, the IR LED is connected in series with a current-limiting resistor to ensure it operates within its specified current range. The anode of the IR LED is connected to the positive terminal of a power supply, while the cathode is connected to one end of the resistor. The other end of the resistor is grounded. This configuration allows the LED to emit infrared light when powered.
The IR phototransistor is connected to a different part of the circuit. Its collector is connected to a positive voltage supply, while the emitter is connected to ground through a load resistor. When the IR LED is activated, it emits infrared light that can be detected by the phototransistor. The phototransistor will conduct when it receives sufficient IR light, allowing current to flow from the collector to the emitter, which can be used to trigger further actions in the circuit, such as activating a relay or lighting an indicator LED.
To enhance the performance of the circuit, it is advisable to use a suitable resistor value for both the IR LED and the phototransistor, depending on their specifications. Additionally, the distance between the IR LED and the phototransistor should be optimized to ensure reliable operation, as the intensity of the emitted infrared light decreases with distance.
This basic circuit can serve as a foundation for various applications, such as remote control systems, simple obstacle detection, or proximity sensors, demonstrating the versatility of IR components in electronic projects.Hello all, Recently I acquired some samples of IR LED`s, and a matching IR Phototransistor. I was bored, and decided to make something with it!..
The project involves the integration of infrared (IR) LEDs with an IR phototransistor to create a simple optical communication system or a basic IR sensor circuit. The IR LED emits infrared light, which is typically invisible to the human eye, while the phototransistor detects this emitted light, allowing for the conversion of light signals into electrical signals.
In this circuit, the IR LED is connected in series with a current-limiting resistor to ensure it operates within its specified current range. The anode of the IR LED is connected to the positive terminal of a power supply, while the cathode is connected to one end of the resistor. The other end of the resistor is grounded. This configuration allows the LED to emit infrared light when powered.
The IR phototransistor is connected to a different part of the circuit. Its collector is connected to a positive voltage supply, while the emitter is connected to ground through a load resistor. When the IR LED is activated, it emits infrared light that can be detected by the phototransistor. The phototransistor will conduct when it receives sufficient IR light, allowing current to flow from the collector to the emitter, which can be used to trigger further actions in the circuit, such as activating a relay or lighting an indicator LED.
To enhance the performance of the circuit, it is advisable to use a suitable resistor value for both the IR LED and the phototransistor, depending on their specifications. Additionally, the distance between the IR LED and the phototransistor should be optimized to ensure reliable operation, as the intensity of the emitted infrared light decreases with distance.
This basic circuit can serve as a foundation for various applications, such as remote control systems, simple obstacle detection, or proximity sensors, demonstrating the versatility of IR components in electronic projects.Hello all, Recently I acquired some samples of IR LED`s, and a matching IR Phototransistor. I was bored, and decided to make something with it!..
G3XTZ DF Rx Details
The receiver is constructed on a single-sided printed circuit board measuring 2 by 4.3 inches. Its compact size allows for installation in various enclosures, which should be adequately shielded. The main directional signal is captured by a tuned ferrite rod...
Infrared control dimming circuit
The receiving circuit operates as follows: when the infrared receiver detects a signal from the remote control transmitter, the KA2184 processes this signal, resulting in a low output at the pin. This low output is directly connected to the base...
Speed of Light with an IR LED
The speed of light has been measured using various methods. This note describes a method that is conceptually easy to understand and relatively simple to implement. The technique utilizes the time-of-flight optical pulse delay method, employing a short (20 nanosecond)...
Reflected light intensity detecting circuit CD4052B CD4011B
The circuit for detecting the intensity of reflected light includes infrared light-emitting diodes, photodiodes, CMOS analog switches, operational amplifiers, and other components. When the circuit operates, the infrared light-emitting diode (LED) initially remains off, allowing the photodiode to receive external...
Receiver for 50 khz optical transmitter
To achieve maximum range, the receiver should be constructed similarly to a radio receiver front end, as the signals received will exhibit comparable frequency components and amplitudes of the photodiode current. The primary limitation on the receiver's performance is the...
200 meters remote control schematic design
Early transmitters using LC oscillators experience significant frequency drift. The introduction of Surface Acoustic Wave (SAW) devices addresses this issue, providing substantial frequency stability comparable to crystals. These devices can achieve fundamental frequencies in the hundreds of megahertz or even...
Simple Direct Conversion Receiver
A low-cost continuous wave (CW) superheterodyne receiver operates with a 4.00 MHz intermediate frequency. While there is no automatic gain control (AGC) or RF gain control, the receiver demonstrates good large signal handling capabilities. The design incorporates six bipolar transistors...
Infrared Heart Pulse Monitor
Senses heart pulse by means of an infrared earlobe clip. Reverse engineered circuit diagram of heart pulse sensor circuit board out of a treadmill. Notice that the output is level shifted for use by CMOS logic running on 4.5V regulated...
Infrared mains remote control Switch
The infra-red (IR) toggle switch project described here is aimed to provide control mechanism for electrical appliances that do not have remote operation features. The goal is to construct a black box where you can plug-in your 120V AC appliance...