Homemade TV remote control off electrical power supply circuit
Description: When the infrared receiver tube PH302 receives a signal from the remote control, the CX20106A selected frequency amplifier outputs a low-frequency signal. The low-level signal charges capacitor C through diodes D and R, causing the negative side potential of C to fall below 1/3 Vcc. This triggers the 555 timer circuit to discharge, cutting off the relay and releasing the shock, thereby disconnecting the power supply. The sensitivity of the RC circuit can be adjusted for operation, and pressing the remote control typically lasts for 3-5 seconds. Pressing switch S1 activates the relay circuit in a self-locking mode when powered on.
The circuit operates based on an infrared remote control system, utilizing the PH302 infrared receiver to detect signals emitted from the remote. Upon receiving a signal, the CX20106A amplifier processes the input, amplifying the low-frequency signal to a level suitable for further processing. The output from the amplifier is directed to a capacitor, denoted as C, which plays a crucial role in the timing and control of the relay mechanism.
Diodes D and R are integral components that facilitate the charging of capacitor C. As the capacitor charges, the voltage across its terminals rises until it reaches a threshold of 1/3 Vcc. This threshold is significant as it is the point at which the 555 timer, configured in monostable mode, triggers a discharge cycle. The discharge effectively activates the relay, which is responsible for controlling the power supply to a connected load.
The relay operates under a self-locking mechanism once switch S1 is engaged. This means that once the relay is activated, it remains in the on state until power is removed, allowing for continuous operation without the need for constant input from the remote control. The sensitivity of the RC circuit can be fine-tuned to adjust the response time of the system, typically set within a range of 3-5 seconds for optimal performance. This ensures that the system can reliably respond to user commands while preventing accidental activation.
Overall, this circuit design exemplifies a practical application of infrared communication and relay control, suitable for various electronic projects requiring remote operation and automated power management.When the infrared receiver tube PH302 receives a signal from the remote control, the CX20106A selected frequency amplifier output a low-frequency signal, the low-level signal by the D and R charges C, so C negative side potential falls below 1 / 3Vcc , .png">555 circuit discharge cutoff relay shock release, cut off the power supply. RC circuit sensitivity can be set to the action, press the remote control is generally 3-5 seconds. Press S1 relay circuit namely self-locking when powered on.
The circuit operates based on an infrared remote control system, utilizing the PH302 infrared receiver to detect signals emitted from the remote. Upon receiving a signal, the CX20106A amplifier processes the input, amplifying the low-frequency signal to a level suitable for further processing. The output from the amplifier is directed to a capacitor, denoted as C, which plays a crucial role in the timing and control of the relay mechanism.
Diodes D and R are integral components that facilitate the charging of capacitor C. As the capacitor charges, the voltage across its terminals rises until it reaches a threshold of 1/3 Vcc. This threshold is significant as it is the point at which the 555 timer, configured in monostable mode, triggers a discharge cycle. The discharge effectively activates the relay, which is responsible for controlling the power supply to a connected load.
The relay operates under a self-locking mechanism once switch S1 is engaged. This means that once the relay is activated, it remains in the on state until power is removed, allowing for continuous operation without the need for constant input from the remote control. The sensitivity of the RC circuit can be fine-tuned to adjust the response time of the system, typically set within a range of 3-5 seconds for optimal performance. This ensures that the system can reliably respond to user commands while preventing accidental activation.
Overall, this circuit design exemplifies a practical application of infrared communication and relay control, suitable for various electronic projects requiring remote operation and automated power management.When the infrared receiver tube PH302 receives a signal from the remote control, the CX20106A selected frequency amplifier output a low-frequency signal, the low-level signal by the D and R charges C, so C negative side potential falls below 1 / 3Vcc , .png">555 circuit discharge cutoff relay shock release, cut off the power supply. RC circuit sensitivity can be set to the action, press the remote control is generally 3-5 seconds. Press S1 relay circuit namely self-locking when powered on.
Atari Joystick Wired Remote Control for Robots
The simplest solution for implementing joystick control for a robot is to program the actions in software on a microcontroller. However, many users prefer off-the-shelf components, thus this circuit is designed using diodes, resistors, transistors, and a FAN8200 motor driver...
Infrared Toggle Switch schematic diagram
All modern infrared (IR) remote control devices generate a continuous coded stream of pulses at 37.9 kHz when any button on the device is pressed. These IR pulses are received and decoded by a compatible device, such as a television...
Infrared headphones transmitter circuit
The transmitter provides an optical link (infrared) for headphones. Three infrared LEDs (IR) are powered by T1, with P1 used to adjust the current level. The current consumption of this headphones infrared transmitter is approximately 60mA at 9V.
The infrared headphone...
Sony KV-S29MHl TV switching power supply (SIR a 80145A) circuit diagram
The circuit of the Sony KV-S29MHl (S Movement series) TV switching power supply (SIR a 80145A) consists of three main sections: (A) the power oscillation part, (B) the regulator part, and (C) the output section.
The Sony KV-S29MHl TV switching power...
Audio
This lab will demonstrate the theory and operation of non-inverting amplifiers as well as their practical application to amplify the signal of a microphone. A non-inverting amplifier will be constructed to increase the output signal of a microphone, which will...
remote control
Step-by-step instructions for adding a remote control interface to F/G CED players, which can be used with a variety of Atari and Sega joysticks, including wireless infrared controllers.
To implement a remote control interface for F/G CED players, the following components...
Battery Powered Tube Regenerative Receiver
The basic regenerative design is quite common. Before the schematic is created, there is a "concept stage," followed by the "available components stage," returning to the "concept stage," then moving on to the "mechanical/electrical layout stage," and finally sketching a...
PC Infrared Receiver
This is the latest version of the Improved Infrared Receiver with Status LED which can control any desktop PC with an ordinary remote control. The project comes along with a small PCB in order to save space. It connects to...
tiny remote for irobot roomba using pic12f629
The Tiny Remote is a compact infrared remote control featuring only two buttons designed to operate an iRobot Roomba. It emits three different infrared signals.
The Tiny Remote is designed for simplicity and ease of use, making it an ideal accessory...