Help me fix the noise in a FM receiver with AC/DC rectifier
#FM receiver
#AC/DC rectifier
#noise reduction
#power supply
#RF circuit
#signal interference
#9V supply
#switch mode power supply
#radio
#receiver circuit
Description: The circuit described is an FM receiver. When a 9V power supply is used, the circuit exhibits good performance. However, performance issues arise when an AC/DC rectifier or switch-mode power supply is utilized.
The FM receiver circuit operates by demodulating frequency-modulated signals to retrieve the original audio signal. The circuit typically consists of several key components: an antenna for signal reception, a radio frequency (RF) amplifier to boost the received signal, a mixer to convert the RF signal to an intermediate frequency (IF), and a demodulator to extract the audio information from the IF signal.
In this particular design, a 9V power supply is optimal, as it provides adequate voltage for the RF amplifier and other active components, ensuring stable performance and sufficient gain. The use of an AC/DC rectifier or a switch-mode power supply may introduce noise or ripple voltage that can adversely affect the sensitive components of the circuit, leading to degraded audio quality or loss of signal.
To enhance the performance of the FM receiver, it is advisable to include bypass capacitors near the power supply pins of the active components. This will help filter out high-frequency noise and stabilize the voltage supply. Additionally, careful layout considerations should be made to minimize interference, such as keeping the RF and audio sections physically separated and using shielded cables for the antenna.
Overall, the FM receiver circuit's performance is highly dependent on the quality of the power supply and the proper design of the circuit layout.The above circuit is fm receiver. when i used pin supply 9V, this circuit had quite nice performence. But when i used AC/DC rectifier or switch supply ..
The FM receiver circuit operates by demodulating frequency-modulated signals to retrieve the original audio signal. The circuit typically consists of several key components: an antenna for signal reception, a radio frequency (RF) amplifier to boost the received signal, a mixer to convert the RF signal to an intermediate frequency (IF), and a demodulator to extract the audio information from the IF signal.
In this particular design, a 9V power supply is optimal, as it provides adequate voltage for the RF amplifier and other active components, ensuring stable performance and sufficient gain. The use of an AC/DC rectifier or a switch-mode power supply may introduce noise or ripple voltage that can adversely affect the sensitive components of the circuit, leading to degraded audio quality or loss of signal.
To enhance the performance of the FM receiver, it is advisable to include bypass capacitors near the power supply pins of the active components. This will help filter out high-frequency noise and stabilize the voltage supply. Additionally, careful layout considerations should be made to minimize interference, such as keeping the RF and audio sections physically separated and using shielded cables for the antenna.
Overall, the FM receiver circuit's performance is highly dependent on the quality of the power supply and the proper design of the circuit layout.The above circuit is fm receiver. when i used pin supply 9V, this circuit had quite nice performence. But when i used AC/DC rectifier or switch supply ..
Radio Glen Transmit Selector system
The main box of the Transmit Selector system is designed to be located in the technical rack of a small radio broadcast station. There are four stereo balanced line inputs, either of which can be routed to a stereo balanced...
car battery charger circuit
The circuit is designed to be powered directly by a power supply, which is why it does not include a transformer, rectifier, or filter capacitors in the schematic. However, these components can be added if desired. To operate the circuit,...
Battery charger or Power Supply 14 volt 4 ampere
The schematic diagram originates from a circuit designed as a battery charger/power supply with an output of 14V and a maximum current of 4A, utilizing the VN64GA MOSFET. This high-performance battery charger is specifically engineered for gelled electrolyte lead-acid batteries,...
Alarm Power Supply
This Power Supply is suitable for the Modular Burglar Alarm. However, it has other applications. It is designed to provide an output of 12-volts, with a current of up to 1-amp. In the event of mains failure, the back-up battery...
FM reciever with LM386
This coil is home-made. It is actually a single layer 'tapped' air core coil. Please refer to my special section on how to make the DRAIN Coil. Once it is made, the tapped leg goes into the middle hole (Refer...
SV3 Radio Magnadyne Radio
Most models produced in the 1930s utilize similar circuits, particularly in the RF section, which follows a common LW-MW-SW scheme. Variations among different models primarily stem from the inclusion or exclusion of variable selectivity control, the sophistication of tone controls,...
FM receivers with PLL
This article discusses simple FM direct conversion radio receivers utilizing a phase-locked loop (PLL). These receivers operate by locking the local oscillator frequency to the input signal. All FM receivers are based on a circuit that combines an oscillator and...
Energy-sucking Radio Antennas
Here's something that has always bugged me: light waves are about 5000 Angstroms in wavelength, while atoms are more like 1 Angstrom across. Atoms are thousands of times smaller than light waves, yet atoms obviously interact very strongly with light....
Farnsworth Model GT-051 Bakelite Radio (1948)
"Black Beauty" is a nickname for a classy Bakelite radio set. It features a dramatic, asymmetrical design with deep wraparound louvers and a bullet-like profile, exemplifying 1940s Streamline design. The radio is undergoing restoration of its electronics and cabinet. Originally,...