Complete Radio Set with MK484 and Loudspeaker
Description: A complete AM radio set based on the MK484 IC (formerly ZN414). It uses a PNP transistor and can drive a 150R loudspeaker. Chad has built a complete radio receiver using 1 IC and a single transistor. The IC requires around 1.2 to 1.6V and this is supplied via the 3V battery in series with 2 diodes 1N4114 diodes, (1N4004 can be substituted) and the 2k volume control.
The AM radio set utilizes the MK484 integrated circuit, which is specifically designed for AM radio reception. The circuit configuration includes a PNP transistor that amplifies the audio signal sufficient to drive a 150-ohm loudspeaker, making it suitable for personal listening applications. The MK484 operates within a voltage range of approximately 1.2 to 1.6 volts, which is achieved through a power supply configuration involving a 3V battery in series with two 1N4114 diodes. This arrangement helps to regulate the voltage supplied to the IC, ensuring stable operation.
The use of 1N4004 diodes as a substitute for the 1N4114 diodes provides flexibility in component selection while maintaining the necessary forward voltage drop to achieve the desired operating voltage for the MK484. The circuit also incorporates a 2k ohm volume control, allowing the user to adjust the audio output level to their preference.
The overall design is compact and efficient, leveraging minimal components to achieve a functional AM radio receiver. The simplicity of the circuit makes it an excellent choice for hobbyists and educational projects, illustrating fundamental principles of radio frequency reception and audio amplification. This AM radio set is a practical demonstration of integrating low-voltage components to create a working audio device.A complete AM radio set based on the MK484 IC (formerly ZN414). It uses a PNP transistor and can drive a 150R loudspeaker. Chad has built a complete radio receiver using 1 IC and a single transistor. The IC requires around 1.2 to 1.6V and this is supplied via the 3V battery in series with 2 diodes 1N4114 diodes, (1N4004 can be substituted) and the 2k volume control.
The AM radio set utilizes the MK484 integrated circuit, which is specifically designed for AM radio reception. The circuit configuration includes a PNP transistor that amplifies the audio signal sufficient to drive a 150-ohm loudspeaker, making it suitable for personal listening applications. The MK484 operates within a voltage range of approximately 1.2 to 1.6 volts, which is achieved through a power supply configuration involving a 3V battery in series with two 1N4114 diodes. This arrangement helps to regulate the voltage supplied to the IC, ensuring stable operation.
The use of 1N4004 diodes as a substitute for the 1N4114 diodes provides flexibility in component selection while maintaining the necessary forward voltage drop to achieve the desired operating voltage for the MK484. The circuit also incorporates a 2k ohm volume control, allowing the user to adjust the audio output level to their preference.
The overall design is compact and efficient, leveraging minimal components to achieve a functional AM radio receiver. The simplicity of the circuit makes it an excellent choice for hobbyists and educational projects, illustrating fundamental principles of radio frequency reception and audio amplification. This AM radio set is a practical demonstration of integrating low-voltage components to create a working audio device.A complete AM radio set based on the MK484 IC (formerly ZN414). It uses a PNP transistor and can drive a 150R loudspeaker. Chad has built a complete radio receiver using 1 IC and a single transistor. The IC requires around 1.2 to 1.6V and this is supplied via the 3V battery in series with 2 diodes 1N4114 diodes, (1N4004 can be substituted) and the 2k volume control.
TDA1083 Am radio receiver circuit diagram electronic project
This AM radio receiver circuit utilizes the TDA1083 radio IC, which is suitable for constructing a simple medium frequency (MF) band radio. The schematic operates within a frequency range of 300 kHz to 3 MHz. The circuit is straightforward and...
Battery Powered Soldering Iron PCB
Traditional soldering irons utilize mains AC supply for heating, which can be inconvenient in the absence of such a power source. This document describes a simple and cost-effective inverter circuit designed for use with standard soldering irons (25W, 30W, 35W)....
Loudspeaker Protection
The detector circuit shown in Figure 1 is simple and works well, and as shown will not trigger with a 30V RMS signal at 5Hz, but operates in 60ms with 30V DC applied, and in 50mS with a 45V DC...
Free-Power AM Radio
Here is something that may interest crystal radio builders: a one-transistor (silicon) AM broadcast receiver that derives its power from ambient AC hum and static. The schematic is adapted from Darryl Boyd's "Stay Tuned" website, which features over 170 articles...
Basic Logic Gate with PNP Transistor
This schematic diagram illustrates a basic logic gate circuit. This PNP transistor circuit can function as either an OR gate or an AND gate, depending on the input states.
The described circuit employs PNP transistors to create a versatile logic gate...
zn415 am radio with tda2822m amplifier
The RF detector circuit, RF amplifier circuit, and automatic gain control circuit (AGC) are integrated within the IC, allowing for the straightforward construction of a high-quality and sensitive AM receiver using this IC. The ZN415E IC is an advanced version...
Loudspeaker Box Amplifier schematic
This original design is a variation on a well-known design, examples of which can be found in a great many texts. My variation was to add a second differential stage to replace the usual common emitter-plus-constant current source. Doing so...
Loudspeaker Tester
Testing loudspeakers is covered in some detail in the passive crossover article, but it is irksome at best to have to fiddle about with clip leads and components lying all over the workbench. This simple project is intended to make...
Two way Loudspeaker cross-over
The resistance of loudspeakers is characterized in a frequency depending on the destination and their press. Loudspeakers are distinguished, as for the destination, in loudspeakers of low frequencies, woofer intermediate, mid-range and high tweeter. Their resistance in Ω is 4Ω,...