1Watt AM CW Transmitter for 10 Meterband

Description: This project involves constructing a simple 3-stage low-power broadcast-type circuit, utilizing a crystal oscillator integrated circuit and a collector modulated AM oscillator with an amplifier. The circuit can be connected to an electret microphone or an amplified dynamic microphone, although the latter typically has too low an output voltage to function effectively (a minimum of 100 mV is required). An electret microphone is depicted in the accompanying diagram. Additionally, a low-frequency preamplifier stage using a single transistor can be incorporated to facilitate the direct connection of a dynamic microphone. The circuit allows for signal reception through the air with nearly any AM radio receiver. While professional AM radio station circuits are significantly more complex, this project provides a fundamental understanding of the principles behind a basic transmitter. It is important to note that transmitting on the 10-meter band requires a valid amateur radio license. Various circuits have been designed for AM transmission, but one of the simplest involves collector modulation applied via a transformer. It is also feasible to create effective designs using solid-state electronics, as implemented in this project with the BC557 transistor. The transmitter is constructed as a Colpitts Oscillator featuring a BSX20 transistor, with a high-frequency output of approximately 50 mW, contingent on a supply voltage ranging from 6 to 15 volts. This output is amplified by a BD135 transistor, increasing the power to around 1 watt at 12 volts. The transmit frequency is stabilized using a 28 MHz crystal, with slight detuning of approximately 1 kHz achievable by employing a 120 pF trimmer capacitor for C8. The oscillator signal is extracted from the collector of T2 and routed to the input of T3, whose output is processed through an L-filter and a low-pass PI filter circuit, effectively cleaning the signal and ensuring spectral purity. The oscillator is activated by T1 and the Morse key (S). By engaging the Morse key, T1 is not used for modulation and is biased, allowing T2 to oscillate freely.

This circuit design provides a practical approach to building a low-power AM transmitter suitable for educational purposes and hobbyist experimentation. The integration of a crystal oscillator ensures frequency stability, which is crucial for minimizing interference and maintaining a clear transmission. The use of a Colpitts oscillator configuration is advantageous due to its simplicity and effectiveness in generating high-frequency signals. The choice of transistors, such as the BSX20 for the oscillator and the BD135 for amplification, reflects a balance between performance and availability, making this circuit accessible to a wide range of builders.

Incorporating a low-frequency preamplifier stage is particularly beneficial when using dynamic microphones, as it enhances the microphone's output to a sufficient level for effective transmission. The inclusion of filtering stages, such as the L-filter and low-pass PI filter, is essential for refining the output signal, reducing unwanted harmonics, and ensuring compliance with spectral purity standards. This attention to detail in signal processing is critical for achieving a quality transmission that can be received clearly by AM radio receivers.

Overall, this project exemplifies fundamental radio transmission principles and offers a hands-on opportunity to explore the intricacies of electronic circuit design and radio frequency communication. Proper attention to licensing regulations and safety practices is recommended when operating any transmission equipment.In this project, you will make a simple 3-stage low-power broadcast-type circuit, using a crystal oscillator integrated circuit and an a collector modulated AM oscillator with amplifier. You can connect the circuit to the an electred microphone or amplified dynamic microphone. Using an electred microphone is shown (in gray) in the diagram below. (no amplified dynamic microphone has a to low output voltage to work. at least 100mv is needed). You could also add a LF preamp stage of one transistor to allow connecting a dynamic microphone directly.

You`ll see that you can receive the signal through the air with almost any AM radio receiver. Although the circuits used in radio stations for AM receiving are far more complicated, this nevertheless gives a basic idea of the concept behind a principle transmitter. Plus it is a lot of fun when you actually have it working! Remember that transmitting on the 10 meter band you`ll need a valid radioamateur license!! A wide range of different circuits have been used for AM, but one of the simplest circuits uses collector modulation applied via (for example) a transformer, while it is perfectly possible to create good designs using solid-state electronics as I applied here (T1 BC557).

The transmitter is build as a Colpitts Oscillator with a BSX20 transistor. HF-output of the oscillator is approx. 50 mW, depending on the supply voltage of 6 to 15 Volts. This is amplified by the BD135 and brings the power up to approx. 1 watt @ 12volts. The transmit frequency is stabilized with the 28Mhz crystal. A slight detuning of approx 1kc is possible when using a 120pF trimmer capacitor for C8. The oscillator signal is taken from the collector of T2 and guided to the input of T3 which output is lead via an L-filter and low-pass PII filter circuit cleaning up the signal pretty good and ensuring spectral purity. The oscillator is keyed by T1 and the morse key (S). By keying the morse-key T1 is not been used for modulation and is biased, hence lets T2 freely oscillate.