Relay control auto-transformer AC power supply circuit
#relay control
#auto-transformer
#LM358
#voltage measurement
#comparator circuit
#AC power
#voltage regulation
#potentiometer
Description: It utilizes two LM358 operational amplifiers, A2 and Ar, to create a voltage measurement comparison control circuit for upper and lower limit voltage settings. The circuit includes a Raspberry Pi adjustment potentiometer (RPi) and an additional potentiometer (RP2) to modify the upper and lower limit voltage settings.
The circuit employs the LM358, a dual operational amplifier, to compare two voltage levels. The first op-amp (A2) is configured to monitor the upper limit voltage, while the second op-amp (Ar) monitors the lower limit voltage. The output of these op-amps will indicate whether the measured voltage exceeds the upper limit or falls below the lower limit.
The potentiometer labeled RPi is connected to the non-inverting input of A2, allowing users to adjust the reference voltage to set the desired upper limit. Similarly, the potentiometer RP2 is connected to the non-inverting input of Ar for adjusting the lower limit voltage. The inverting inputs of both op-amps are connected to the voltage being measured, which is compared against the set reference voltages.
When the measured voltage exceeds the upper limit, the output of A2 will switch to a high state, indicating an over-voltage condition. Conversely, if the measured voltage drops below the lower limit, the output of Ar will switch to a high state, signaling an under-voltage condition. This dual comparison setup enables effective monitoring of voltage levels and can be used in various applications, including power supply regulation, battery management systems, and safety alarms.
The circuit can be further enhanced by integrating additional components such as LEDs or relays that can be activated based on the op-amp outputs, providing visual or physical indications of voltage status. This design ensures that the system can react promptly to voltage deviations, maintaining operational safety and reliability.It uses two LM358 op amp A2 and Ar as an upper limit and a lower limit voltage electrical voltage measurement comparison control circuit. RPi adjustment potentiometer and RP2, can change the upper limit voltage and lower voltage setting.
The circuit employs the LM358, a dual operational amplifier, to compare two voltage levels. The first op-amp (A2) is configured to monitor the upper limit voltage, while the second op-amp (Ar) monitors the lower limit voltage. The output of these op-amps will indicate whether the measured voltage exceeds the upper limit or falls below the lower limit.
The potentiometer labeled RPi is connected to the non-inverting input of A2, allowing users to adjust the reference voltage to set the desired upper limit. Similarly, the potentiometer RP2 is connected to the non-inverting input of Ar for adjusting the lower limit voltage. The inverting inputs of both op-amps are connected to the voltage being measured, which is compared against the set reference voltages.
When the measured voltage exceeds the upper limit, the output of A2 will switch to a high state, indicating an over-voltage condition. Conversely, if the measured voltage drops below the lower limit, the output of Ar will switch to a high state, signaling an under-voltage condition. This dual comparison setup enables effective monitoring of voltage levels and can be used in various applications, including power supply regulation, battery management systems, and safety alarms.
The circuit can be further enhanced by integrating additional components such as LEDs or relays that can be activated based on the op-amp outputs, providing visual or physical indications of voltage status. This design ensures that the system can react promptly to voltage deviations, maintaining operational safety and reliability.It uses two LM358 op amp A2 and Ar as an upper limit and a lower limit voltage electrical voltage measurement comparison control circuit. RPi adjustment potentiometer and RP2, can change the upper limit voltage and lower voltage setting.
Power Supply 0-30V / 0-2A
The basic requirements for a laboratory power supply are to provide the necessary voltages and currents with low output resistance, low noise, minimal ripple, and good stabilization. These requirements are addressed within the circuit design. Many power supplies incorporate electronic...
Voltage Regulators
Until Willow Garage was acquired, there was work as a Web Robotics Engineer. This title reflects a role as a full-stack engineer focused on real-time, distributed robot control. Notable projects include an XML-RPC server and client for Node.js, a deprecated...
Circuit audio pre-amplifier integrated circuit LM358 dual op amp
The LM358 series consists of two independent, high-gain, internally frequency-compensated operational amplifiers designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible, and the low power supply...
Regulated 12 Volt Supply
This circuit utilizes a 13-volt zener diode (D2) for voltage regulation. Approximately 0.7 volts are dropped across the base-emitter junction of the transistors, resulting in a higher current output of 12.3 volts. The circuit is capable of supplying loads up...
Simple Pre-Regulator
There will be many occasions when it is beneficial to utilize the P05 supply module sourced from a higher voltage supply. For instance, this could be advantageous when integrating balanced inputs.
The P05 supply module is designed to facilitate the conversion...
AC Power Monitor
This AC Power Monitor continuously monitors the AC power line voltage for both under-voltage conditions and missing cycles. When it detects a total of 5 or 6 consecutive missing half-cycles (50ms, 50/60Hz), it activates a relay and initiates a timer....
EIGHT CHANNEL COMPUTERIZED 3SUP1 SUP SUB2 SUB DIGIT_VM
Displays up to eight different DC voltages on a CRT terminal of a microprocessor under keyboard control, using BASIC commands and a BASIC routine provided in the article. Utilizes a modified Motorola MC14433 dual-lamp integrating analog-to-digital converter. An unknown voltage...
Op-Amp Based PWM Circuit
This circuit utilizes LM358 operational amplifiers (or any single supply operational amplifier) to generate a pulse-width modulated (PWM) signal. The design was specifically created for a local marine repair company that requested a circuit that is easily repairable and does...
Voltage regulator for projection lamp
The circuit regulates the RMS output voltage across a load, specifically a projection lamp, to 100 volts ±2% for input voltages ranging from 105 to 250 volts AC. This regulation is achieved by indirectly sensing the light output of lamp...