Fluorescent Tube Power Supply Circuit
#2N3055
#oscillator
#transformer
#ferrite rod
#filament switch
#fluorescent tube
#homemade
#transistor
#high voltage
#electronics
Description: A 2N3055 oscillator (Q1) drives a homemade transformer, wound on a Vk ferrite rod. S2 is used as a filament switch and can be eliminated if desired. A 20-W fluorescent tube is recommended. The supply voltage is 12 V.
The circuit employs a 2N3055 transistor configured as an oscillator, which is a common approach in power supply applications. The 2N3055 is a robust NPN power transistor capable of handling significant current and voltage levels, making it suitable for driving a transformer. In this design, the oscillator generates a high-frequency signal that is used to excite the transformer.
The transformer itself is custom-built, utilizing a Vk ferrite rod as the core material. Ferrite rods are advantageous in high-frequency applications due to their low losses and high magnetic permeability. The winding configuration of the transformer can be optimized to match the desired output characteristics for the fluorescent tube.
S2 functions as a filament switch, allowing for control over the filament power supply. While it provides convenience for switching the circuit on and off, it is noted that this component can be omitted if the application does not require independent control of the filament.
The system is designed to operate at a supply voltage of 12 V, which is a common voltage level for low-power applications. The recommendation of a 20-W fluorescent tube indicates the intended load for the circuit, suggesting that the design must accommodate the necessary current and voltage requirements to ensure proper operation of the tube.
In summary, this schematic provides a straightforward approach to building a fluorescent lamp driver using a 2N3055 transistor and a homemade transformer, suitable for applications requiring efficient power conversion and control. A 2N3055 oscillator (Ql) drives a homemade transformer, wound on a Vk, ferrite rod. S2 is used as a filament switch and it can be eliminated, if desired. A 20-W fluorescent tube is recommended. The supply is 12 V.
The circuit employs a 2N3055 transistor configured as an oscillator, which is a common approach in power supply applications. The 2N3055 is a robust NPN power transistor capable of handling significant current and voltage levels, making it suitable for driving a transformer. In this design, the oscillator generates a high-frequency signal that is used to excite the transformer.
The transformer itself is custom-built, utilizing a Vk ferrite rod as the core material. Ferrite rods are advantageous in high-frequency applications due to their low losses and high magnetic permeability. The winding configuration of the transformer can be optimized to match the desired output characteristics for the fluorescent tube.
S2 functions as a filament switch, allowing for control over the filament power supply. While it provides convenience for switching the circuit on and off, it is noted that this component can be omitted if the application does not require independent control of the filament.
The system is designed to operate at a supply voltage of 12 V, which is a common voltage level for low-power applications. The recommendation of a 20-W fluorescent tube indicates the intended load for the circuit, suggesting that the design must accommodate the necessary current and voltage requirements to ensure proper operation of the tube.
In summary, this schematic provides a straightforward approach to building a fluorescent lamp driver using a 2N3055 transistor and a homemade transformer, suitable for applications requiring efficient power conversion and control. A 2N3055 oscillator (Ql) drives a homemade transformer, wound on a Vk, ferrite rod. S2 is used as a filament switch and it can be eliminated, if desired. A 20-W fluorescent tube is recommended. The supply is 12 V.
Common emitter amplifier input and output signals of the phase relationship
The common emitter amplifier circuit exhibits a specific phase relationship between its input and output signals. This configuration is widely utilized in various electronic devices primarily for its high voltage gain. However, the output impedance is higher than the input...
Simple Metronome With Transistors
A flip-flop, functioning as an astable multivibrator, can be utilized to generate timing signals in music applications such as a metronome. This can be achieved by adjusting the transistor bias resistor with a value of 100k.
The astable multivibrator configuration of...
Precision tandem type power supply circuit diagram
The circuit depicted features a secondary N3 center tap transformer (T) with a common point connecting diodes VD2 and VD3 to positive electrodes, along with capacitors C2, C6, C7, and negative electrodes connected to capacitors C9 and C10. Additional components...
Circuit Project: 12KV High Voltage Generator
The hobby circuit described utilizes a unique approach to generate approximately 12,000 volts with a current of about 5 µA. It employs two silicon-controlled rectifiers (SCRs) that form dual pulse generator circuits. These SCRs discharge a 0.047 µF capacitor rated...
Driving a fluorescent tube
Even though a fluorescent tube is not a neon glow lamp and this page may not be the most appropriate location, this circuit is intriguing because it employs an unconventional method to power a common lamp. Similar to glow lamps,...
Homemade metal detector
This homemade metal detector circuit is designed to locate objects made of materials with relatively high magnetic permeability. While it may not be sensitive enough for detecting buried coins, it can effectively identify larger metallic treasures. The circuit operates using...
Transistor Ignition
This transistor ignition circuit enhances vehicle starting and ensures smoother engine operation, especially at both high and low RPMs. It contributes to lower fuel consumption, reduced emissions, and decreased maintenance costs. The system promotes economical and electronic driving.
The transistor ignition...
High voltage switching stabilized voltage supply circuit
A high voltage switching stabilized voltage supply circuit is illustrated in the diagram. This is the switching power supply for an 80P type color television. It utilizes auto-excitation and a PWM circuit. The output is isolated from the power system,...
5-V-oscillator
This low-cost oscillator is consistently self-starting and capable of operating from over 1 Hz to 10 MHz, requiring only five components. The period of oscillation can be calculated using the relationship: P = 5 x 10^3 C seconds when C...