5 A stabilized power supply
#voltage regulator
#78xx
#transistor
#5A
#stabilized
#power supply
#current limit
#MJ2955
#heat sink
Description: This is a simple but powerful nutrition that less than 5 A can deliver. The circuit works by using a normal type 78xx voltage regulator and a buffer transistor. When the output current over 200 mA, then take over the T1, which limits the maximum output current is 5 Amps. The 1978 series regulator is available from 5 to 24 volts. In the place of the xx is the voltage, so 7812 for a 12 volt regulator. Take the AC in 5% higher than the desired output voltage. In that case, one under the wrinkle. MJ is a T1 (E) in 2955. This higher output currents must be well chilled.
More: R1 = 3.3 ? 5 watt C1 = V 4700?F/63 C2 = V 10?F/35 C3 = 100nF D1 = 35A T1 = MJ2955 (TO220), MJE2955 (TO3), TIP2955 (TO247) IC1 = 78xx F1 = 5A
The described circuit is a regulated power supply capable of delivering up to 5 Amperes of output current, which is suitable for various applications requiring stable voltage and current. The core of the circuit utilizes a 78xx series linear voltage regulator, which is designed to provide a fixed output voltage ranging from 5V to 24V, depending on the specific model used (e.g., 7812 for 12V output).
To enhance the current handling capabilities, a buffer transistor (T1) is employed, which is typically a power transistor such as the MJ2955. This transistor operates in conjunction with the voltage regulator to ensure that the output current does not exceed 5A. When the load demands more than 200mA, the buffer transistor takes over, effectively limiting the output current to the specified maximum of 5A.
The circuit includes several key components for stability and performance. The resistor R1, rated at 3.3 ohms and 5 watts, is likely used for current sensing or feedback purposes. Capacitors C1, C2, and C3 serve to filter and stabilize the voltage output. C1, rated at 4700µF/63V, acts as a bulk capacitor to smooth out voltage fluctuations. C2, with a value of 10µF/35V, provides additional filtering, while C3, a 100nF capacitor, helps suppress high-frequency noise.
Diode D1, rated at 35A, is included for reverse polarity protection and to prevent back EMF from damaging the circuit components. The fuse F1, rated at 5A, serves as a safety feature to protect the circuit from overcurrent conditions.
To ensure proper operation, the input AC voltage should be at least 5% higher than the desired output voltage. This is crucial for the linear regulator to function correctly, as it requires a minimum voltage differential (headroom) between the input and output. Adequate heat dissipation must be considered for T1, as handling higher output currents generates significant heat; therefore, a suitable heat sink is essential to maintain reliable operation.
Overall, this circuit design is straightforward yet effective for applications requiring a reliable power supply with a stable output voltage and current.This is a simple but powerful nutrition that less than 5 A can deliver. The circuit works by using a normal type 78xx voltage regulator and a buffer transistor. When the output current over 200 mA, then take over the T1, which limits the maximum output current is 5 Amps. The 1978 series regulator is available from 5 to 24 volts. In the place of the xx is the voltage, so 7812 for a 12 volt regulator. Take the AC in 5% higher than the desired output voltage. In that case, one under the wrinkle. MJ is a T1 (E) in 2955. This higher output currents must be well chilled. R1 = 3.3 ? 5 watt C1 = V 4700?F/63 C2 = V 10?F/35 C3 = 100nF D1 = 35A T1 = MJ2955 (TO220), MJE2955 (TO3), TIP2955 (TO247) IC1 = 78xx F1 = 5A
More: R1 = 3.3 ? 5 watt C1 = V 4700?F/63 C2 = V 10?F/35 C3 = 100nF D1 = 35A T1 = MJ2955 (TO220), MJE2955 (TO3), TIP2955 (TO247) IC1 = 78xx F1 = 5A
The described circuit is a regulated power supply capable of delivering up to 5 Amperes of output current, which is suitable for various applications requiring stable voltage and current. The core of the circuit utilizes a 78xx series linear voltage regulator, which is designed to provide a fixed output voltage ranging from 5V to 24V, depending on the specific model used (e.g., 7812 for 12V output).
To enhance the current handling capabilities, a buffer transistor (T1) is employed, which is typically a power transistor such as the MJ2955. This transistor operates in conjunction with the voltage regulator to ensure that the output current does not exceed 5A. When the load demands more than 200mA, the buffer transistor takes over, effectively limiting the output current to the specified maximum of 5A.
The circuit includes several key components for stability and performance. The resistor R1, rated at 3.3 ohms and 5 watts, is likely used for current sensing or feedback purposes. Capacitors C1, C2, and C3 serve to filter and stabilize the voltage output. C1, rated at 4700µF/63V, acts as a bulk capacitor to smooth out voltage fluctuations. C2, with a value of 10µF/35V, provides additional filtering, while C3, a 100nF capacitor, helps suppress high-frequency noise.
Diode D1, rated at 35A, is included for reverse polarity protection and to prevent back EMF from damaging the circuit components. The fuse F1, rated at 5A, serves as a safety feature to protect the circuit from overcurrent conditions.
To ensure proper operation, the input AC voltage should be at least 5% higher than the desired output voltage. This is crucial for the linear regulator to function correctly, as it requires a minimum voltage differential (headroom) between the input and output. Adequate heat dissipation must be considered for T1, as handling higher output currents generates significant heat; therefore, a suitable heat sink is essential to maintain reliable operation.
Overall, this circuit design is straightforward yet effective for applications requiring a reliable power supply with a stable output voltage and current.This is a simple but powerful nutrition that less than 5 A can deliver. The circuit works by using a normal type 78xx voltage regulator and a buffer transistor. When the output current over 200 mA, then take over the T1, which limits the maximum output current is 5 Amps. The 1978 series regulator is available from 5 to 24 volts. In the place of the xx is the voltage, so 7812 for a 12 volt regulator. Take the AC in 5% higher than the desired output voltage. In that case, one under the wrinkle. MJ is a T1 (E) in 2955. This higher output currents must be well chilled. R1 = 3.3 ? 5 watt C1 = V 4700?F/63 C2 = V 10?F/35 C3 = 100nF D1 = 35A T1 = MJ2955 (TO220), MJE2955 (TO3), TIP2955 (TO247) IC1 = 78xx F1 = 5A
Long-Duration Time Delay
Transistor Q1 and resistors R1, R2, and R3 form a constant current source, with the charge current adjustable to as low as a few nanoamperes. This current is insufficient to activate the UJT, where IP is 0.2 A, unless a...
regulator
Malcolm Moore's schematic is good, but it is insufficient for someone inexperienced with a soldering iron to create anything functional. Specifically, T1 is a coil of some type, but the configuration, as well as the values for Q1 and Q2,...
Switch Mode Power Supply
National Semiconductor has been producing and designing integrated circuits (ICs) for use in switch-mode power supplies for many years. The application of these devices is standard.
National Semiconductor has established a significant presence in the design and manufacturing of integrated circuits...
lie detector
The circuit diagram of the Lie Detector consists of three transistors (TR1 to TR3), a capacitor (C1), two LEDs (L1 & L2), five resistors (R1 to R5), and a variable resistor (VR1). Suitable transistors include BC547, BC548, or BC549, or...
Power Supply Failure Alarm
This is a specialized circuit design for a power supply failure alarm. Most power supply failure alarm or indicator circuits require an independent power supply. However, the alarm circuit presented here...
The power supply failure alarm circuit is designed to monitor...
Water Activated Relay
In this circuit, two transistors are configured as a high-gain compound pair. Transistor T1 is likely a 2N2222A, while T2 is identified as a BC108. The current gain is calculated as the product of the beta values of each transistor,...
-15 V 1-A Regulated Power Supply
The supply receives -20 V from the rectifier/filter which is fed to the collector of the Darlington pnp pass transistor, a TIP105. The base drive to the TIP105 is supplied through resistor R5. The base of the TIP is driven...
MCU power supply wiring portion
High-precision voltage regulator, isolation transformer with the correct wiring, and low-pass filter to enhance the electrical noise immunity of the source portion. The wiring in Figures 20-48 and 20-49 is illustrated in the figures. Chokes (L1, L2) should have an...
MDRC Mark 4 20 Amp Power Supply
The MDRC committee approached the author to take on the role of Electronic Components and Project Officer, which was accepted without hesitation. Upon assuming the position, it became evident that more time would be required than initially anticipated, primarily for...