Low-Drift/Low-Noise Dc Amplifier
#low-noise
#dc amplifier
#chopper modulation
#low-drift
#op-amp
#signal conditioning
#precision amplifier
#carrier-modulation
#IC1
Description: Figure 39-2's circuit combines a low-noise operational amplifier, IC1, with a chopper-based carrier-modulation scheme to achieve a low-noise, low-drift DC amplifier whose performance exceeds any currently available monolithic amplifier. The amplifier's offset is less than 1 mV, and its drift is less than 0.05 µV/°C. This circuit has noise within a 10-Hz bandwidth of less than 40 nV. The amplifier's bias current, set by the bipolar input of IC1, is approximately 25 nA. The 74C04 inverters (IC3 to IC6) form a simple 2-phase square-wave clock that operates at about 350 Hz. The complementary oscillator signals (φ1 and φ2) drive switches S1 and S2, respectively, causing a chopped version of the input to appear at IC1's input. IC1 amplifies this AC signal. Switches S3 and S4 synchronously demodulate IC1's square-wave output. Because S3 and S4 switch in sync with S1 and S2, the circuit presents accurate amplitude and polarity information to IC2, the DC output amplifier. This output stage integrates the square wave to provide a DC voltage output. Resistors R1 and R2 divide the output and feed it back to the input chopper, where the divided output serves as a zero signal reference. The ratio of R1 and R2 sets the gain, in this case to 1000.
The described circuit employs a low-noise operational amplifier (IC1) that operates in a chopper-stabilized configuration. This design is particularly advantageous for applications requiring high precision and stability over varying temperatures. The low offset voltage and minimal drift characteristics make this amplifier suitable for sensitive measurement tasks. The noise performance, specified at less than 40 nV within a 10-Hz bandwidth, indicates that the circuit is designed to minimize interference from external noise sources, which is critical for high-fidelity signal processing.
The 74C04 inverters are utilized to generate a stable 2-phase square-wave clock signal, essential for the chopper modulation technique. This clock signal, operating at approximately 350 Hz, is responsible for switching the input signal on and off, effectively reducing low-frequency noise and drift. The synchronous operation of switches S1 and S2 ensures that the input signal is accurately sampled and processed.
The demodulation stage, comprising switches S3 and S4, is crucial for retrieving the amplified signal from the chopper-modulated output of IC1. This stage ensures that the output retains the correct amplitude and polarity, which is necessary for the subsequent DC amplification by IC2. The integration of the square-wave signal into a DC output is achieved through the output stage, which effectively converts the modulated signal back into a usable form.
Feedback resistors R1 and R2 play a vital role in determining the gain of the amplifier circuit. By setting the ratio of these resistors, the gain can be precisely adjusted to the desired level, in this case, a gain of 1000. This feedback mechanism not only stabilizes the circuit but also allows for fine-tuning of the output voltage, ensuring that it meets the requirements of the specific application. Overall, this circuit design exemplifies advanced techniques in analog signal processing, yielding a high-performance amplifier suitable for demanding electronic applications. Figure 39-2"s circuit combines a low-noise op amp, IC1, with a chopper-based carrier-modulation scheme to achieve a low-noise, low-drift dc amplifier whose performance exceeds any currently available monolithic amplifier. The amplifier"s offset is less than 1, and its drift is less than 0.05 /iV/°C. This circuit has noise within a 10-Hz bandwidth less than 40 nV. The amplifier"s bias current, which is set by the bipolar input of IC1, is about 25 nA. The 74C04 inverters (IC3 to IC6) form a simple 2-phase square-wave clock that runs at about 350 Hz. The complementary oscillator signals ( and O2) provide drive to SI and S2, respectively, causing a chopped version of the input to appear at ICl"s input.
IC1 amplifies this ac signal. S3 and S4 synchronously demodulate ICl"s square-wave output. Because S3 and S4 switch synchronously with SI and S2, the circuit presents proper amplitude and polarity information to IC2, the dc output amplifier. This output stage integrates the square wave to provide a dc voltage output. Rl and R2 divide the output and feed it back to the input chopper where the divided output serves as a zero signal reference.
The ratio of Rl and R2 sets the gain, in this case to 1000.
The described circuit employs a low-noise operational amplifier (IC1) that operates in a chopper-stabilized configuration. This design is particularly advantageous for applications requiring high precision and stability over varying temperatures. The low offset voltage and minimal drift characteristics make this amplifier suitable for sensitive measurement tasks. The noise performance, specified at less than 40 nV within a 10-Hz bandwidth, indicates that the circuit is designed to minimize interference from external noise sources, which is critical for high-fidelity signal processing.
The 74C04 inverters are utilized to generate a stable 2-phase square-wave clock signal, essential for the chopper modulation technique. This clock signal, operating at approximately 350 Hz, is responsible for switching the input signal on and off, effectively reducing low-frequency noise and drift. The synchronous operation of switches S1 and S2 ensures that the input signal is accurately sampled and processed.
The demodulation stage, comprising switches S3 and S4, is crucial for retrieving the amplified signal from the chopper-modulated output of IC1. This stage ensures that the output retains the correct amplitude and polarity, which is necessary for the subsequent DC amplification by IC2. The integration of the square-wave signal into a DC output is achieved through the output stage, which effectively converts the modulated signal back into a usable form.
Feedback resistors R1 and R2 play a vital role in determining the gain of the amplifier circuit. By setting the ratio of these resistors, the gain can be precisely adjusted to the desired level, in this case, a gain of 1000. This feedback mechanism not only stabilizes the circuit but also allows for fine-tuning of the output voltage, ensuring that it meets the requirements of the specific application. Overall, this circuit design exemplifies advanced techniques in analog signal processing, yielding a high-performance amplifier suitable for demanding electronic applications. Figure 39-2"s circuit combines a low-noise op amp, IC1, with a chopper-based carrier-modulation scheme to achieve a low-noise, low-drift dc amplifier whose performance exceeds any currently available monolithic amplifier. The amplifier"s offset is less than 1, and its drift is less than 0.05 /iV/°C. This circuit has noise within a 10-Hz bandwidth less than 40 nV. The amplifier"s bias current, which is set by the bipolar input of IC1, is about 25 nA. The 74C04 inverters (IC3 to IC6) form a simple 2-phase square-wave clock that runs at about 350 Hz. The complementary oscillator signals ( and O2) provide drive to SI and S2, respectively, causing a chopped version of the input to appear at ICl"s input.
IC1 amplifies this ac signal. S3 and S4 synchronously demodulate ICl"s square-wave output. Because S3 and S4 switch synchronously with SI and S2, the circuit presents proper amplitude and polarity information to IC2, the dc output amplifier. This output stage integrates the square wave to provide a dc voltage output. Rl and R2 divide the output and feed it back to the input chopper where the divided output serves as a zero signal reference.
The ratio of Rl and R2 sets the gain, in this case to 1000.
Op Amp Classic Gain and Linearity Testing
The diagram below illustrates a classic test fixture that has been utilized for an extended period to assist individuals in addressing non-linearity errors.
The classic test fixture depicted in the diagram serves as a fundamental tool in electronics testing and calibration....
Signal-conditioner-with-bridge
The LT1007 is capable of providing excitation current directly to bias the 350-0 bridge at 5 V. With only 5 V across the bridge, as opposed to the usual 10 V, total power dissipation and bridge warm-up drift is reduced....
Metronome Circuit
This circuit utilizes two operational amplifiers (op-amps) to create a unique sound effect. The first op-amp, CA741, is configured as a standard astable multivibrator, generating timing pulses controlled by components C1, R2, and variable resistor VR1. The output from this...
DC to 100W amplifier circuit diagram of 500KHZ
A 100W amplifier with a frequency range from DC to 500KHz features a photoelectric starting operational amplifier with high input impedance and high gain characteristics, enabling transformerless output power of 100W. The load current can reach up to 10A, necessitating...
Power Function Circuit
It is possible to easily generate various non-linear functions such as X^(1/2), X^2, X^3, 1/X, XY, and X/Y using logarithms. In this context, division is transformed into subtraction, while multiplication is converted into addition.
The application of logarithmic properties in electronic...
Voltage Controlled Voltage Source
The drawback of the circuit mentioned is that the operational amplifier (op-amp) supply is connected to the high voltage (HV) supply. Most op-amps are limited to approximately 30V for their supply voltage, which prevents the circuit from functioning with higher...
Dc-gain-controlled-video-amplifier
This amplifier utilizes a cascaded operational amplifier (op amp) integrator and a transistor buffer, Q1, to drive the gain control element. With a minor modification, the HA-5190/5195 stage is configured as a conventional non-inverting op amp and includes input and...
op amp based sound detector circuit
This circuit is designed for sound detection and generates an output signal when sound is detected. This output can trigger another circuit that activates an alarm, making it suitable for security applications. The circuit employs a condenser microphone to capture...
Precision Amplifiers
It has been mentioned that the operational amplifier (op amp) in the second stage may be damaged. Confirmation is requested by testing the op amp in a buffer configuration or any simple configuration. This test is necessary to ascertain whether...