Swiss ML Testakica

Description: The Unit is started by hand by revolving the two disks in opposite directions and continues to move without further input. This device has only two moving parts namely the bearing races at the centre of the disk. The disks are made of clear plastic upon which are placed flat a series of fifty blade type steel or aluminium sections equally spaced around the middle sections of each disk. The speed of the revolving disks is about 50 to 60 rpm limited to this by magnetic impulses from the magnetic section on the rim. To those that have seen this powerhouse in operation it is certain that usable power is being extracted from the environment and some is being used to run the machine. This is an energy system which relies on the self-moving Wimshurst electrostatic generator for the high voltage and somehow the members of this commune have found a way to extract, amplify and convert this energy to powerful useful levels. The Swiss M/l converter is based on a modified Wimshurst electrostatic machine. My people have seen the Swiss M/l converter in operation but to date no one has been able to understand or successfully reproduce the results as claimed by the Swiss commune group Methernitha in Linden. But to one fortunate individual had a visit to Paul B. who is claimed to have said that if they could understand the above following experiment they would be close to understanding how the device was able to work. It consists of two plates of metal one aluminium the other copper separated by an insulator of some unknown material could be paper or plastic (unknown). It also included a horseshoe magnet wrapped with a coil of wire and both ends soldered together. Paul B placed this capacitor made of the differing metals between the poles of a horseshoe magnet and then asked a witness to connect the plates to two probes of a voltmeter to each plate and to their surprise found a voltage of seven hundred volts which occasionally dropped in value. I have communicated with some people who have performed the above experiment with little result however. WHAT I THINK HAPPENED ALTHOUGH I DON'T KNOW FOR SURE PB may have conditioned the insulator of perspex or other similar insulator by the following means without revealing what he had done. It is known that if you heat perspex or lucite until soft to touch and becomes tacky and you then subject the heated mass to a high voltage field via means of metal plates on each side of the perspex mass and leave it there until the perspex is cool. Removing the applied high voltage charge an electrostatic high voltage charge may still be continuously taken from those metal plates something like this also happens with the electrostatic microphones in modern tape recorders. What part the magnet and the coil and differing face metal plates plays in addition to the electrostatic charge is yet to be determined by yours truly. Looking at other parts of the machine the pickup fields that don't touch the spinning disks are also made up of perforated Aluminium separated with a perspex insulated and with copper behind it. I would like to know if anyone has performed the above experiment and got a successful result. BASED OF THE WIMSHURST MACHINE The theory of operation of a Wimshurst machine is. The disks are of plastic, glass, hard rubber or in one case I saw old phonograph records. The contra rotating disk causes air molecules to become electrically activated by the fictional movement of the air both disks causes. This rotating action causes the disks to become continually charged and an electrostatic charge builds up, causing a flashover. To stop this flashover, a series of foil sections are attached to the centre portion of each disk and equally spaced and back to back with foil sections on the outer sides. To remove the charge, collection arms are arranged to collect the charge and transfers the charge to a storage capacitor. At 45 degrees to these collection points is a neutralising bar that extends to full length of the disk and has brushes at both ends. A neutralising brush equals the charges on the metal foil position at both positions on both sides. The neutralising bar on opposite side disk is at ninety degrees to the one for the other side. For many the cans in front of the Testakica have proved to be a bit of a mystery. From information I have obtained the general opinion is that the above diagram is close to explaining what in the twin cans. It seems to be a combination of two copper cylinders interlaid with two perforated alumina screens. In the middle are six or more doughnut magnets upon which are wrapped coils some think they could be bifilar in nature. Between each magnet there is an air gap made possible by the plastic spacers between each of them. In the middle of the magnets, there is a single spiral of copper or aluminium metal. It is possible although not confirmed that there is a common ground at the bottom of each can connecting all these elements. Don't quote me on this but it reminds me of an automotive transformer connected in reverse and shielded with copper and aluminium shielding. I'm not sure what roles the magnets provide but Tesla used a magnetic field in his designs to give a DC voltage output like modern-day rectifiers in some of his AC circuits. The magnets may also work similarly to work carried out by Captain Hans Coler.

The device operates on the principle of electrostatics, utilizing a Wimshurst machine configuration. The two disks are rotated in opposite directions to generate an electrostatic charge through the frictional contact with the surrounding air. The disks are equipped with metal foil sections that facilitate charge collection, which is then transferred to a storage capacitor via collection arms. The neutralizing bar, positioned at 45 degrees to the collection points, serves to balance the charges and prevent flashover, which is a common occurrence in such electrostatic systems.

The additional components, such as the horseshoe magnet and the coils wrapped around it, introduce magnetic fields that may enhance the electrostatic generation or storage capabilities of the system. The configuration of the magnets and coils suggests a complex interaction that could potentially amplify the output voltage, as indicated by the voltage readings observed during the experimentation with the capacitor setup.

The overall design integrates various materials, including plastics and metals, which are chosen for their specific electrical properties. The use of insulators like perspex in conjunction with conductive materials may play a critical role in maintaining charge separation and enhancing the device's efficiency. The experimental results reported indicate a need for further investigation into the conditioning of the insulator and its interaction with the electrostatic and magnetic fields.

In summary, the operation of this device hinges on the interplay between mechanical motion, electrostatic charge generation, and magnetic field interactions, forming a unique energy system that has yet to be fully understood or replicated in conventional engineering practices.The Unit is started by hand by revolving the two disks in opposite directions and continues to move without further input. This device has only two moving parts namely the bearing races at the centre of the disk. The disk are made of clear plastic upon which are placed flat a series of fifty blade type steel or aluminium sections equally spaced around the middle sections of each disk.

The speed of the revolving disks is about 50 to 60 rpm limited to this by magnetic impulses from the magnetic section on the rim. To those that have seen this powerhouse in operation it is certain that useable power is being extracted from the environment and some is being used to run the machine. This is an energy system which relies on the self moving wimhurst electro static generator for the high voltage and somehow the members of this commune have found a way to extract ,amplify and convert this energy to powerful useful levels.

The Swiss M/l converter is based on a modified wimshurst electrostatic machine. My people have seen the swiss m/l converter in operation but to do date no one has been able to understand or successfully reproduced the results as claim by the Swiss commune group Methernitha in Linden . But to one fortunate individual had a visit to Paul B.who is claimed to have had said that if they could understand the above following experiment they would be close to understanding how the device was able to work.(as illustrated above) It consists of two plates of metal one aluminium the other copper separated by a insulator of some unknown material could be paper or plastic(unknown) It also included a horse shoe magnet wrapped with a coil of wire and both ends soldered together.

Paul B placed this capacitor made of the differing metals between the poles of a horse shoe magnet and then asked a witnesses to connect the plates to two probes of a voltmeter to each plate and to their surprise found a voltage of seven hundred volts which occasionally dropped in value.. I have communicated with some people how have performed the above experiment with little result however.

WHAT I THINK HAPPENED ALTHOUGH I DON'T KNOW FOR SURE PB may have conditioned the insulator of perspex of other similiar insulator by the following means without revealing what he had had done. It is known that if you heat perspex or lucite until soft to touch and becomes tacky and you then subject the heated mass to a high voltage field via means of metal plates on each side of perspex mass and leave it there until the perspex is cool .Removing the applied high voltage charge an electrostatic high voltage charge may still be continously taken from those metal plates something like this also happens with the electrostatic microphones in modern tape recorders..

What part the magnet and the coil and differing face metal plates plays in additional to the electrostatic charge is yet to be determined by yours truly. Looking at other parts of the machine the pickup fields that don't touch the spinning disks are also made up of perforated Aluminium separated with a perspex insulated and withcopper behind it.

I would like to know if any one has performed the above experiment and got a successful result. BASED OF THE WIMSHURST MACHINE The theory of operation of a wimhurst machine is. The disks are of plastic, glass, hard rubber or in one case I saw old phonograph records. The contra rotating disk causes air molecules to become electrically activated by the fictional movement of the air both disks causes. This rotating action causes the disks to become continually charged and an electrostatic charge builds up, causing a flash over.

To stop this flash over, a series of foil sections are attached to the centre portion of each disk and equally spaced and back to back with foil sections on the outer sides. To remove the charge, collection arms are arranged to collect the charge and transfers the charge to a storage capacitor.

At 45 degrees to these collection points is a neutralising bar that extends to full length of the disk and has brushes at both ends. A neutralising brush equals the charges on the metal foil position at both positions on both sides. The neutralising bar on opposite side disk is at ninety degrees to the one for the other side. For many the cans in front of the Testakica have proved to be a bit of a mystery. From information I have obtained the general opinion is that the above diagram is close to explaining what in the twin cans.

It seems to a combination of two copper cylinders interlaid with two perforated alumina screens In the middle are six or more doughnut magnets upon which are wrapped coils some think they could be bifilar in nature. Between each magnet there is an air gap made possible by the plastic spacers between each of them. In the middle of the magnets there is a single spiral of copper or aluminium metal. It is possible although not confirmed that there is a common ground at the bottom of each can connecting all these elements.

Don't quote me on this but it reminds me of an automotive transformed connected in reverse and shielded with copper and aluminium shielding. I not sure what roles the magnets provide but tesla used a magnet field in his designs to give a dc voltage output like modern day rectifiers in some of his AC circuits.

The magnets may also work similiar to work carried out by Captain Hans Coler.