Auto Baud Rate with PIC18F2455
#PIC18F2455
#auto baud rate
#EUSART
#UART
#microcontroller
#serial communication
#baud rate detection
#SPBRG
#BRG clock
Description: Most of the newer PIC come with the EUSART module which have the function for auto baud rate detection. The features allow a person to set the baud rate at runtime by sending the character "U" or 0x55 to the PIC. With ABDEN (auto baud rate enable) bit set and using BRG clock as a reference, each rising edge occurring on the RX pin is taken as a reference to calculate the SPBRG and SPBRGH value. After the Baud rate is set, the RCIF flag will be set. The receive register must be discarded as it doesn't contain meaningful data. The Image (PIC18F2455 datasheet, page 252) below shows the timing diagram for auto baud rate setup. A circuit based similar to the UART test is used to demonstrate the capability of auto baud rate generation. Using the code in the project file attached, It will 1st wait for a character "U" to be send over for baud rate calculation. Auto baud is enable using the 3 lines of code below. The UARTReadByte() will read and discard the byte after a successful configuration of baud rate. The LCD display will be the same as the image below after a successful program of the microcontroller. It is currently waiting for the character U to set the baud rate.
The described circuit utilizes the Enhanced Universal Asynchronous Receiver-Transmitter (EUSART) module found in newer PIC microcontrollers, specifically the PIC18F2455. The EUSART module is equipped with an automatic baud rate detection feature that enhances communication efficiency in serial communications. The operation begins with the microcontroller waiting for a specific character, "U" (0x55), which is sent over the RX pin. This character triggers the auto baud rate detection functionality, which is enabled by setting the ABDEN bit in the control register.
Upon receiving the character, the microcontroller uses the BRG clock as a reference to determine the baud rate by counting the rising edges on the RX pin. This process involves calculating the values for SPBRG and SPBRGH registers, which are essential for configuring the baud rate. Once the baud rate is successfully set, the RCIF (Receive Interrupt Flag) is activated, indicating that the baud rate configuration has been completed. It is important to note that the data in the receive register is not meaningful in this context and should be discarded.
The implementation of this functionality is further demonstrated through a circuit similar to a UART test setup. The attached project file contains code that initializes the microcontroller and configures the auto baud rate detection. The UARTReadByte() function is utilized to read and subsequently discard the byte received after the baud rate has been configured. This is critical to ensure that the system does not process irrelevant data.
In conjunction with the microcontroller, an LCD display is employed to provide visual feedback. After the successful programming of the microcontroller, the LCD will reflect the system's status, indicating that it is waiting for the character "U" to initiate the baud rate setting process. This comprehensive setup illustrates the capability of the EUSART module to dynamically adapt to varying baud rates, thus enhancing the robustness and flexibility of serial communication in embedded systems.Most of the newer PIC come with the EUSART module which have the function for auto baud rate detection. The features allow a person to set the baud rate at runtime by sending the character "U" or 0x55 to the PIC.
With ABDEN (auto baud rate enable) bit set and using BRG clock as a reference, each rising edge occurring on the RX pin is taken as a reference to calculate the SPBRG and SPBRGH value. After the Baud rate is set, the RCIF flag will be set. The receive register must be discarded as it doesn't contain meaningful data. The Image (PIC18F2455 datasheet, page 252) below shows the timing diagram for auto baud rate setup. A circuit based similar to the UART test is used to demonstrate the capability of auto baud rate generation.Using the code in the project file attached, It will 1st wait for a character "U" to be send over for baud rate calculation. Auto baud is enable using the 3 lines of code below. The UARTReadByte() will read and discard the byte after a successful configuration of baud rate. The LCD display will be the same as the image below after a successful program of the microcontroller.
It is currently waiting for the character U to set the baud rate.
The described circuit utilizes the Enhanced Universal Asynchronous Receiver-Transmitter (EUSART) module found in newer PIC microcontrollers, specifically the PIC18F2455. The EUSART module is equipped with an automatic baud rate detection feature that enhances communication efficiency in serial communications. The operation begins with the microcontroller waiting for a specific character, "U" (0x55), which is sent over the RX pin. This character triggers the auto baud rate detection functionality, which is enabled by setting the ABDEN bit in the control register.
Upon receiving the character, the microcontroller uses the BRG clock as a reference to determine the baud rate by counting the rising edges on the RX pin. This process involves calculating the values for SPBRG and SPBRGH registers, which are essential for configuring the baud rate. Once the baud rate is successfully set, the RCIF (Receive Interrupt Flag) is activated, indicating that the baud rate configuration has been completed. It is important to note that the data in the receive register is not meaningful in this context and should be discarded.
The implementation of this functionality is further demonstrated through a circuit similar to a UART test setup. The attached project file contains code that initializes the microcontroller and configures the auto baud rate detection. The UARTReadByte() function is utilized to read and subsequently discard the byte received after the baud rate has been configured. This is critical to ensure that the system does not process irrelevant data.
In conjunction with the microcontroller, an LCD display is employed to provide visual feedback. After the successful programming of the microcontroller, the LCD will reflect the system's status, indicating that it is waiting for the character "U" to initiate the baud rate setting process. This comprehensive setup illustrates the capability of the EUSART module to dynamically adapt to varying baud rates, thus enhancing the robustness and flexibility of serial communication in embedded systems.Most of the newer PIC come with the EUSART module which have the function for auto baud rate detection. The features allow a person to set the baud rate at runtime by sending the character "U" or 0x55 to the PIC.
With ABDEN (auto baud rate enable) bit set and using BRG clock as a reference, each rising edge occurring on the RX pin is taken as a reference to calculate the SPBRG and SPBRGH value. After the Baud rate is set, the RCIF flag will be set. The receive register must be discarded as it doesn't contain meaningful data. The Image (PIC18F2455 datasheet, page 252) below shows the timing diagram for auto baud rate setup. A circuit based similar to the UART test is used to demonstrate the capability of auto baud rate generation.Using the code in the project file attached, It will 1st wait for a character "U" to be send over for baud rate calculation. Auto baud is enable using the 3 lines of code below. The UARTReadByte() will read and discard the byte after a successful configuration of baud rate. The LCD display will be the same as the image below after a successful program of the microcontroller.
It is currently waiting for the character U to set the baud rate.
IR On/Off Switch Using Microcontroller
Turning electrical devices ON or OFF using a remote control is a well-established concept, with numerous devices available that perform this function effectively. To create such a device, it is necessary to construct a receiver and a transmitter, as well...
delay circuit for photography
This article outlines the construction of a simple microcontroller-based delay circuit designed for photographic applications such as drop or high-speed photography. It can control the trigger lag of cameras and flash units, generate periodic trigger pulses, or manage magnetic valves....
microcontroller Generate a reset signal from a falling edge trigger
The microcontroller design features the microcontroller (MCU) in hibernation mode, which can only be awakened by a pulse (high-low-high) signal on the reset pin (active low). An accelerometer or an external real-time clock (RTC) serves as the wake-up source. The...
Controlling high-current circuits
Digital output from a microcontroller is typically a low-amperage signal. For example, when a pin is set HIGH on the microcontroller (in Wiring/Arduino, it is digitalWrite(somePin, HIGH);), the voltage from that pin is usually +3.3V or +5V, with the current...
POWER LINE MODEM FOR COMPUTER CONTROL
This circuit employs an 87C57 microcontroller along with several peripherals to convert X-10 power-line carrier-code formats from a personal computer for use with an X-10 power-line interface in a home-control system. Software details can be found in the reference.
The circuit...
High Resolution Digital Weigh-scale Design Using Z8 Encore! ?® Microcontrollers
The SP6691 circuit is designed to provide a high output voltage using a lower voltage boost regulator by incorporating a charge pump circuit. This configuration can convert a standard 30V boost regulator into a 60V boost regulator if necessary. Testing...
Automatic Switch Project
Model railroad turnouts, often referred to as switches, can be controlled in various ways. The simplest method is manual control, operated by hand. Remote activation is typically achieved through pneumatic (air) or electrical means. The project discussed in these articles...
serial communication using UART in RFID project
A project is being developed utilizing RFID (Radio Frequency Identification) technology. The microcontroller chosen for this project is the AT89C51/52/S52. Serial communication is being implemented using RS-232.
The project involves the integration of RFID technology for identification and data exchange applications....
Robot Tutorials
The UART, or Universal Asynchronous Receiver/Transmitter, is a feature of microcontrollers that facilitates serial data communication (text, numbers, etc.) with a PC. This device converts incoming parallel data (within the microcontroller/PC) to serial data that can be transmitted over a...