Geiger Counter Schematic Help
#Geiger Counter
#radiation detection
#sensor
#NerdKit
#computer interface
#Fukushima
#nuclear
#schematic
#electronics project
Description: With the recent events at the Fukushima Dai-ichi nuclear power plant, it would be interesting to build a Geiger Counter and connect it to a NerdKit for interfacing with a computer. An article detailing the building process is available, which includes a schematic; however, the section that describes the circuit does not explain how it functions. A request is made for a detailed write-up on the circuit, explaining the role of each component to achieve the desired outcome. The author notes that while some aspects of the schematic are understandable, the power section appears to be complicated. The following breakdown of various sections has been provided, along with the author's interpretations.
- Lower Left Corner: "D9," a 9V battery, some capacitors, and a 7805 voltage regulator. This section appears to convert 25VDC to 5VDC with adequate current capacity while providing battery backup. The 7805 is similar to its application in the NerdKit. It is believed that the Vcc from this section supplies power to the "Vcc" sections elsewhere in the schematic, although this may not be entirely accurate.
- Left Central: U1a-d, "D1," capacitors, resistors, Q1, T1 (left side). This section functions as a square wave pulse generator to drive the transformer T1. Other diagrams have shown a hex inverter IC (U1 pins a-d) used in conjunction with a resistor-capacitor configuration to produce a square wave output. This section can be likened to a heavy-duty version of a 555 timer that does not utilize a 555 IC.
- Right Upper Central: T1 (right side), D2-6, capacitors. This area generates high power DC. The transformer steps up the square wave DC to a higher voltage, resulting in a distorted square wave. The diodes and capacitors then rectify this to a semi-steady DC voltage. Zener diodes D4-6 regulate the voltage to the GM tube at approximately 500VDC, while resistor R4 limits current to prevent arcing within the GM tube.
- Mid Far Right: Q2, U1e, capacitors, resistors. The GM tube produces a very fast but small pulse (in the nanosecond to microsecond range). The transistor and inverter, along with the capacitor and resistor, shape these pulses to a +5/0V signal suitable for U2, while also preventing high voltage from reaching U2. The transistor functions as a crude amplifier in this section, converting the tiny pulses from the GM tube into more recognizable logic transitions.
- Lower Right Central: U2, capacitors, resistors, speaker, LED, headphone jack. U2 is a 555 timer configured as a pulse stretcher, converting the microsecond pulses from the previous section into a longer pulse that can be visually indicated by an LED or audibly signaled through a speaker. This application is common for 555 timers, and most datasheets provide examples of similar configurations. The roles of the LED, speaker, and headphone jack are considered self-explanatory.
The described circuit represents a functional Geiger Counter design that effectively converts radiation detection into a readable format, utilizing various electronic components to achieve the desired signal processing and output. Each section of the circuit plays a critical role in ensuring accurate detection and representation of radiation levels, making it a valuable tool for monitoring environmental conditions.With the recent events at the Fukushima Dai-ichi nuclear power plant, I thought it would be pretty cool to build a Geiger Counter and hook it up to my NerdKit for interfacing with my computer. I`ve found this article which explains the building process pretty well, and also includes a schematic: Unfortunately, the section that describes the circui
t really doesn`t explain how the circuit works. This may be a huge request, but could somebody do a writeup on this circuit that explains what each component does to get the end result I`ve been looking over the circuit but my inexperience with such schematics isn`t helping at all. I am not an electrical guru, but from what i can read most of the schematic makes sense, althought the power part is really messy.
I have broken out a few of the sections below with what I believe they do. Any of the pros around here should feel free to jump in and point out where i am going wrong. hopefully it helps, but if you want more detail I will try. -Lower Left Corner : "D9", a 9v battery, some caps and a 7805 - This looks like a way to convert the 25VDC to 5VDC with decent current capacity and have a battery backup. The 7805 portion is very similar to how it is used on the NK. I think the Vcc leaving this section is being used to feed the "Vcc" sections elsewhere in the diagram, but I migh be wrong.
- Left Central: U1a-d, "D1", caps, resistors, Q1, T1 left side - This is a square wave pulse generator to feed the transformer T1. I have seen other diagrams where a hex inverter IC (U1 pins a-d) is used with an ResistorCapacitor setup to create a square wave output train.
(think of this section as heavy duty 555, that doesn`t use a 555 per say) - Right Upper Central: T1 right side, D2-6, caps - This section on the right side of T1, is the high power DC generation section. The transformer steps the squarewave DC up to a higher voltage ugly square wave and then the diodes and caps clean it up to a semi-steady DC.
The Zeners, D4-6, effectively "regulate" the voltage to the GM tube at ~500Vdc. R4 is of course to keep the current down and prevent arcing inside the GM tube. -MidFarRight: Q2, U1e, caps, resists - The GM tube outputs a very fast (nano-microsec) but very small pulse. the transistor and inverter with the help of the capacitor and resistor, shape the pulses to +5/0V in the proper orientation for U2 and keep the high voltage from getting to the U2.
The transistor acts like an crude amplifier in this portion, making the tiny blips out of the GM tube closer to logic transistions. -Lower Right Central: U2, caps, resistors, speaker, LED, headphone jack - U2 is a 555 being used as a pulse stretcher to take the ysec pulses from the previous section and convert them into a pulse that is visible when flashed on an LED or Audible when put on the speaker.
This is a very typical use for 555`s and most datasheets have a diagram of them being used like this. I am going to assume the LED, speaker, and headphone jack are pretty self-explanitory.
- Lower Left Corner: "D9," a 9V battery, some capacitors, and a 7805 voltage regulator. This section appears to convert 25VDC to 5VDC with adequate current capacity while providing battery backup. The 7805 is similar to its application in the NerdKit. It is believed that the Vcc from this section supplies power to the "Vcc" sections elsewhere in the schematic, although this may not be entirely accurate.
- Left Central: U1a-d, "D1," capacitors, resistors, Q1, T1 (left side). This section functions as a square wave pulse generator to drive the transformer T1. Other diagrams have shown a hex inverter IC (U1 pins a-d) used in conjunction with a resistor-capacitor configuration to produce a square wave output. This section can be likened to a heavy-duty version of a 555 timer that does not utilize a 555 IC.
- Right Upper Central: T1 (right side), D2-6, capacitors. This area generates high power DC. The transformer steps up the square wave DC to a higher voltage, resulting in a distorted square wave. The diodes and capacitors then rectify this to a semi-steady DC voltage. Zener diodes D4-6 regulate the voltage to the GM tube at approximately 500VDC, while resistor R4 limits current to prevent arcing within the GM tube.
- Mid Far Right: Q2, U1e, capacitors, resistors. The GM tube produces a very fast but small pulse (in the nanosecond to microsecond range). The transistor and inverter, along with the capacitor and resistor, shape these pulses to a +5/0V signal suitable for U2, while also preventing high voltage from reaching U2. The transistor functions as a crude amplifier in this section, converting the tiny pulses from the GM tube into more recognizable logic transitions.
- Lower Right Central: U2, capacitors, resistors, speaker, LED, headphone jack. U2 is a 555 timer configured as a pulse stretcher, converting the microsecond pulses from the previous section into a longer pulse that can be visually indicated by an LED or audibly signaled through a speaker. This application is common for 555 timers, and most datasheets provide examples of similar configurations. The roles of the LED, speaker, and headphone jack are considered self-explanatory.
The described circuit represents a functional Geiger Counter design that effectively converts radiation detection into a readable format, utilizing various electronic components to achieve the desired signal processing and output. Each section of the circuit plays a critical role in ensuring accurate detection and representation of radiation levels, making it a valuable tool for monitoring environmental conditions.With the recent events at the Fukushima Dai-ichi nuclear power plant, I thought it would be pretty cool to build a Geiger Counter and hook it up to my NerdKit for interfacing with my computer. I`ve found this article which explains the building process pretty well, and also includes a schematic: Unfortunately, the section that describes the circui
t really doesn`t explain how the circuit works. This may be a huge request, but could somebody do a writeup on this circuit that explains what each component does to get the end result I`ve been looking over the circuit but my inexperience with such schematics isn`t helping at all. I am not an electrical guru, but from what i can read most of the schematic makes sense, althought the power part is really messy.
I have broken out a few of the sections below with what I believe they do. Any of the pros around here should feel free to jump in and point out where i am going wrong. hopefully it helps, but if you want more detail I will try. -Lower Left Corner : "D9", a 9v battery, some caps and a 7805 - This looks like a way to convert the 25VDC to 5VDC with decent current capacity and have a battery backup. The 7805 portion is very similar to how it is used on the NK. I think the Vcc leaving this section is being used to feed the "Vcc" sections elsewhere in the diagram, but I migh be wrong.
- Left Central: U1a-d, "D1", caps, resistors, Q1, T1 left side - This is a square wave pulse generator to feed the transformer T1. I have seen other diagrams where a hex inverter IC (U1 pins a-d) is used with an ResistorCapacitor setup to create a square wave output train.
(think of this section as heavy duty 555, that doesn`t use a 555 per say) - Right Upper Central: T1 right side, D2-6, caps - This section on the right side of T1, is the high power DC generation section. The transformer steps the squarewave DC up to a higher voltage ugly square wave and then the diodes and caps clean it up to a semi-steady DC.
The Zeners, D4-6, effectively "regulate" the voltage to the GM tube at ~500Vdc. R4 is of course to keep the current down and prevent arcing inside the GM tube. -MidFarRight: Q2, U1e, caps, resists - The GM tube outputs a very fast (nano-microsec) but very small pulse. the transistor and inverter with the help of the capacitor and resistor, shape the pulses to +5/0V in the proper orientation for U2 and keep the high voltage from getting to the U2.
The transistor acts like an crude amplifier in this portion, making the tiny blips out of the GM tube closer to logic transistions. -Lower Right Central: U2, caps, resistors, speaker, LED, headphone jack - U2 is a 555 being used as a pulse stretcher to take the ysec pulses from the previous section and convert them into a pulse that is visible when flashed on an LED or Audible when put on the speaker.
This is a very typical use for 555`s and most datasheets have a diagram of them being used like this. I am going to assume the LED, speaker, and headphone jack are pretty self-explanitory.
Automatic Room light Control With Bi Directional Visitor Counter
The objective of this project is to create a controller-based model that counts the number of individuals entering a specific room and activates the lighting accordingly. This is achieved through the use of sensors that detect the current number of...
Geiger Counter Uses Cockroft-Walton Multiplier
The recent tsunami in Japan and the ongoing calamity at the Fukushima nuclear power plant has significantly increased sales of radiation meters.
The surge in demand for radiation meters can be attributed to heightened public awareness and concern regarding radiation exposure...
Victoreen Model CD V-700 Schematic Diagram
This is the schematic for the 6A model located at the bottom of the unit, which is incorrect. These units have been subjected to movement for over 40 years, leading to many bottoms being swapped due to battery corrosion in...
Building a device from a schematic
A common issue encountered is that individuals possess a schematic, also known as a circuit diagram, that they wish to construct. However, they discover that there are...
Building a circuit from a schematic requires a clear understanding of the components involved...
metal detector project circuit
A schematic diagram for a metal detector has been found. The project does not need to be original and can be sourced from the internet. There are several questions regarding this schematic. One query pertains to a small arrow connected...
Automatic plant waterer
The unit consists of a sensor, timer, and electric water pump. The sensor is embedded in the soil, and when dry, the electronics operate the water pump for a preset time. The circuit is composed of a level-sensitive Schmitt trigger,...
Pocket-sized geiger counter
A single 6.75 V mercury battery powers the counter, which features a 1 mA count-rate meter as well as an aural output. A regulated 900 V supply provides stable operation of the counter tube. A multivibrator, built around a differential...
Gate automatic lamp circuit
The circuit utilizes multiple integrated circuits to form an automatic lighting device that is activated by door and window sensors. It includes CD4093 digital integrated circuits, a relay, and a power supply circuit. The system typically remains closed when a...
build your own geiger counter
The basic Geiger counter circuit is similar to the previous version, with the addition of components for three optional enhancements: an external power input, a headphone jack, and a digital output, highlighted in red. The external power input is designed...