Using white LEDs
Description: The yellow LEDs are on a small PCB, which are easy to remove. On the PCB there are 3 yellow LEDs and 4 diodes. Pictures of the PCB can be seen here: Top-side - Bottom-side. The schematic is as follows: You now remove the 3 LEDs and the 3 normal diodes (the ones who are in series). I actually only removed the outer 2 as the remainder is then left unconnected. The value of zener diode and the resistor can be changed, but I found a value of 470 Ohm/5W for the resistor and 3.3 Volt for the zener to be OK. You can also put 4 or 5 normal diodes in series instead of the standard 3 - but it may be hard to fit them. Now you place a zener diode instead of the normal diodes, and the white LEDs instead of the yellow LEDs. It should be connected as this schematic describes:
The described circuit involves a small printed circuit board (PCB) equipped with three yellow light-emitting diodes (LEDs) and four diodes. The design allows for easy removal of the components, facilitating modifications and replacements. The initial configuration includes three yellow LEDs connected in parallel, with the four diodes arranged in series.
To modify the circuit, the three yellow LEDs and three of the normal diodes are removed. It is noted that removing only the outer two diodes leaves the center diode unconnected, which can be beneficial for maintaining circuit integrity while making changes.
The circuit design incorporates a zener diode and a resistor. The recommended values for the resistor are 470 Ohms with a power rating of 5 Watts, while a zener voltage of 3.3 Volts is suggested to ensure proper voltage regulation. The resistor limits the current flowing through the zener diode, protecting it from excessive current that could lead to failure.
The design allows flexibility in the number of normal diodes used in series; however, accommodating four or five diodes may present physical fitting challenges on the PCB.
For the final modification, the yellow LEDs are replaced with white LEDs, and the normal diodes are substituted with a zener diode. The zener diode serves to regulate voltage for the white LEDs, ensuring they operate within their specified voltage range. The circuit should be connected according to the provided schematic to ensure proper functionality and performance of the white LEDs. This configuration allows for effective light emission while maintaining circuit stability and reliability.The yellow LEDs are on a small PCB, which are easy to remove. On the PCB there is 3 yellow LEDs and 4 diodes. Pictures of the PCB can be seen here : Top-side - Bottom-side. The schematic is as follows : You now remove the 3 LEDs and the 3 normal diodes (the ones who are in series). I actually only removed the outer 2 as the remainder is then left unconnected. The value of zener diode and the resistor, can be changed, but I found a value of 470 Ohm/5W for the resistor and 3,3 Volt for the zener to be OK.
You can also put 4 or 5 normal diodes in series instead of the standard 3 - but it may be hard to fit them. Now you place a zener diode instead of the normal diodes, and the white LEDs instead of the yellow LEDs.
It should be connected as this schematic describes :
The described circuit involves a small printed circuit board (PCB) equipped with three yellow light-emitting diodes (LEDs) and four diodes. The design allows for easy removal of the components, facilitating modifications and replacements. The initial configuration includes three yellow LEDs connected in parallel, with the four diodes arranged in series.
To modify the circuit, the three yellow LEDs and three of the normal diodes are removed. It is noted that removing only the outer two diodes leaves the center diode unconnected, which can be beneficial for maintaining circuit integrity while making changes.
The circuit design incorporates a zener diode and a resistor. The recommended values for the resistor are 470 Ohms with a power rating of 5 Watts, while a zener voltage of 3.3 Volts is suggested to ensure proper voltage regulation. The resistor limits the current flowing through the zener diode, protecting it from excessive current that could lead to failure.
The design allows flexibility in the number of normal diodes used in series; however, accommodating four or five diodes may present physical fitting challenges on the PCB.
For the final modification, the yellow LEDs are replaced with white LEDs, and the normal diodes are substituted with a zener diode. The zener diode serves to regulate voltage for the white LEDs, ensuring they operate within their specified voltage range. The circuit should be connected according to the provided schematic to ensure proper functionality and performance of the white LEDs. This configuration allows for effective light emission while maintaining circuit stability and reliability.The yellow LEDs are on a small PCB, which are easy to remove. On the PCB there is 3 yellow LEDs and 4 diodes. Pictures of the PCB can be seen here : Top-side - Bottom-side. The schematic is as follows : You now remove the 3 LEDs and the 3 normal diodes (the ones who are in series). I actually only removed the outer 2 as the remainder is then left unconnected. The value of zener diode and the resistor, can be changed, but I found a value of 470 Ohm/5W for the resistor and 3,3 Volt for the zener to be OK.
You can also put 4 or 5 normal diodes in series instead of the standard 3 - but it may be hard to fit them. Now you place a zener diode instead of the normal diodes, and the white LEDs instead of the yellow LEDs.
It should be connected as this schematic describes :
Handy Pen Torch Circuit
This easy-to-construct handy pen torch electronic circuit has a low component count and utilizes two power white LEDs for illumination. A low voltage (4.8V DC) supply is derived from a built-in rechargeable Ni-Cd battery pack and is converted into two...
28 LED Clock Timer
This is a programmable clock timer circuit that utilizes individual LEDs to indicate hours and minutes. Twelve LEDs can be arranged in a circle to represent the 12 hours of a clock face, and an additional 12 LEDs can be...
1.5 Volt LED Flasher Circuits
The LED flasher circuits below operate on a single 1.5 volt battery. The circuit on the upper right uses the popular LM3909 LED flasher IC and requires only a timing capacitor and LED. The top left circuit, designed by Andre...
LED Night Lamp
This circuit is usable as a Night Lamp when a wall mains socket is not available to plug-in an ever running small neon lamp device. In order to ensure minimum battery consumption, one 1.5V cell is used, and a simple...
White LED Night Light Circuit
White Light Emitting Diodes (LEDs) now available can serve as a strong alternative to incandescent lamps in lighting applications. Today's White LEDs are...
White Light Emitting Diodes (LEDs) represent a significant advancement in lighting technology, offering energy efficiency, longevity, and reduced...
audio How to make LED bar graphs to measure intensity
Convert the LEDs into LED bar graphs that display intensity. For instance, a song with a strong bass should cause the bar graph to rise to the maximum. The segments of the LED bar graph should consist of individual LEDs....
simple current controlled led tube
The circuit of a current-controlled LED tube light employs high-voltage transistors to implement the necessary current control operation based on a fundamental principle. A resistor (R2) is utilized to convert the increasing current into a voltage across itself. This voltage...
220V Flashing LED Circuit
An AC mains operated single LED flasher circuit is constructed using the widely utilized CMOS timer chip TLC555. The entire circuit is powered directly from the 230VAC grid supply via a capacitive potential divider and associated components. This compact LED...
220 V LED Night light
This is a capacitor power supply. This is a very small current of energy-effective because it has very little loss, much smaller than the miniature transformer. Capacitor impedance is inversely proportional to frequency. This is a great disadvantage when the...