Power Failure Light
#power failure
#relay
#LED
#backup power
#mains power
#emergency lighting
#PCB
#security
#low voltage
Description: This is a very basic power failure lighting circuit based around a relay. This simple circuit has many uses, from lighting up rooms and walkways in the case of a power failure, to monitoring and security uses. There are many different power failure circuits out there based on 555 timers or transistors but they all have different problems including limited input voltage, price and complexity, and poor backup power. This unit has been designed to work with mains power all the way down to 5 volts, and power 3 LEDs to provide light for a hallway or a child's room in the event of power failure. The PCB includes many simple add-ons and modifications too. More: This circuit is connected to ac power through J1 then rectified to dc through D1-D4. D5 is a 12 volt zener diode being used along with the resistor R1 and the coil resistance of relay RL1 to regulate the input voltage to 12 volts and C1 is used to help smooth this power. The relay RL1 is a SPDT 5vDc relay and when power is applied to it, it opens the circuit with the LEDs so they are off as long as power is on if the power goes off, the relay closes the circuit and the battery BAT1 powers the LEDs D6, D7, and D8. In this circuit BAT1 is a 9 volt battery that powers the 3 LEDs through R3; however BAT1 can be many different batteries depending on your needs. J4 is also available in parallel with the LEDs to connect a buzzer or etc.
This power failure lighting circuit is designed to operate efficiently across a wide range of input voltages, from a minimum of 5 volts DC to a maximum of 240 volts AC. The circuit architecture is centered around a relay (RL1), which plays a crucial role in controlling the flow of power to the light-emitting diodes (LEDs) during normal and power failure conditions.
The circuit begins with the connection to AC power via connector J1. This AC voltage is then rectified to DC using a bridge rectifier composed of diodes D1 to D4. The rectification process converts the alternating current into a usable direct current, which is then smoothed by capacitor C1 to reduce voltage fluctuations and provide a stable DC output.
To maintain a consistent output voltage for the relay and LEDs, a 12-volt zener diode (D5) is employed in conjunction with resistor R1 and the coil resistance of relay RL1. This configuration ensures that the voltage supplied to the relay remains regulated at 12 volts, which is essential for the reliable operation of the relay.
Relay RL1 is a single-pole double-throw (SPDT) relay rated for 5 volts DC. When AC power is present, the relay is energized and opens the circuit to the LEDs (D6, D7, and D8), keeping them off. In the event of a power failure, the relay deactivates, allowing the circuit to close, and the backup power from battery BAT1 is activated. This battery, typically a 9-volt type, provides the necessary power to illuminate the LEDs, ensuring that the area remains lit during an outage.
The circuit also includes a provision for flexibility in power source selection. While BAT1 is specified as a 9-volt battery, the design allows for the use of various battery types depending on user requirements. Additionally, there is an option to connect a buzzer or other devices through connector J4, which is wired in parallel with the LEDs, enhancing the circuit's functionality for monitoring or alerting purposes.
The overall power consumption of the circuit is approximately 450 mW, making it energy-efficient while providing essential lighting and monitoring capabilities during power outages. This design is suitable for a variety of applications, including residential lighting, security systems, and other scenarios where reliable backup lighting is necessary.This is a very basic power failure lighting circuit based around a relay. This simple circuit has many uses, from lighting up rooms and walkways in the case of a power failure, to monitoring and security uses. There are many different power failure circuits out there based on 555 timers or transistors but they all have different problems including limited input voltage, price and complexity, and poor backup power.
This unit has been designed to work with mains power all the way down to 5 volts, and power 3 LEDs to provide light for a hallway or a child's room in the event of power failure. The PCB includes many simple add-ons and modifications too. This circuit is connected to ac power through J1 then rectified to dc through D1-D4. D5 is a 12 volt zener diode being used along with the resistor R1 and the coil resistance of relay RL1 to regulate the input voltage to 12 volts and C1 is used to help smooth this power. The relay RL1 is a SPDT 5vDc relay and when power is applied to it, it opens the circuit with the LEDs so they are off as long as power is on if the power goes off, the relay closes the circuit and the battery BAT1 powers the LEDs D6, D7, and D8.
In this circuit BAT1 is a 9 volt battery that powers the 3 LEDs through R3; however BAT1 can be many different batteries depending on your needs. J4 is also available in parallel with the LEDs to connect a buzzer or etc. Input Voltage Max: 240 Volts AC Input Voltage Min: 5 Volts DC Approximant Power Consumption: 450 mW
This power failure lighting circuit is designed to operate efficiently across a wide range of input voltages, from a minimum of 5 volts DC to a maximum of 240 volts AC. The circuit architecture is centered around a relay (RL1), which plays a crucial role in controlling the flow of power to the light-emitting diodes (LEDs) during normal and power failure conditions.
The circuit begins with the connection to AC power via connector J1. This AC voltage is then rectified to DC using a bridge rectifier composed of diodes D1 to D4. The rectification process converts the alternating current into a usable direct current, which is then smoothed by capacitor C1 to reduce voltage fluctuations and provide a stable DC output.
To maintain a consistent output voltage for the relay and LEDs, a 12-volt zener diode (D5) is employed in conjunction with resistor R1 and the coil resistance of relay RL1. This configuration ensures that the voltage supplied to the relay remains regulated at 12 volts, which is essential for the reliable operation of the relay.
Relay RL1 is a single-pole double-throw (SPDT) relay rated for 5 volts DC. When AC power is present, the relay is energized and opens the circuit to the LEDs (D6, D7, and D8), keeping them off. In the event of a power failure, the relay deactivates, allowing the circuit to close, and the backup power from battery BAT1 is activated. This battery, typically a 9-volt type, provides the necessary power to illuminate the LEDs, ensuring that the area remains lit during an outage.
The circuit also includes a provision for flexibility in power source selection. While BAT1 is specified as a 9-volt battery, the design allows for the use of various battery types depending on user requirements. Additionally, there is an option to connect a buzzer or other devices through connector J4, which is wired in parallel with the LEDs, enhancing the circuit's functionality for monitoring or alerting purposes.
The overall power consumption of the circuit is approximately 450 mW, making it energy-efficient while providing essential lighting and monitoring capabilities during power outages. This design is suitable for a variety of applications, including residential lighting, security systems, and other scenarios where reliable backup lighting is necessary.This is a very basic power failure lighting circuit based around a relay. This simple circuit has many uses, from lighting up rooms and walkways in the case of a power failure, to monitoring and security uses. There are many different power failure circuits out there based on 555 timers or transistors but they all have different problems including limited input voltage, price and complexity, and poor backup power.
This unit has been designed to work with mains power all the way down to 5 volts, and power 3 LEDs to provide light for a hallway or a child's room in the event of power failure. The PCB includes many simple add-ons and modifications too. This circuit is connected to ac power through J1 then rectified to dc through D1-D4. D5 is a 12 volt zener diode being used along with the resistor R1 and the coil resistance of relay RL1 to regulate the input voltage to 12 volts and C1 is used to help smooth this power. The relay RL1 is a SPDT 5vDc relay and when power is applied to it, it opens the circuit with the LEDs so they are off as long as power is on if the power goes off, the relay closes the circuit and the battery BAT1 powers the LEDs D6, D7, and D8.
In this circuit BAT1 is a 9 volt battery that powers the 3 LEDs through R3; however BAT1 can be many different batteries depending on your needs. J4 is also available in parallel with the LEDs to connect a buzzer or etc. Input Voltage Max: 240 Volts AC Input Voltage Min: 5 Volts DC Approximant Power Consumption: 450 mW
Ultra Bright LED Lamp circuit
This ultra-bright white LED lamp operates on 230V AC with low power consumption. It is suitable for illuminating VU meters, SWR meters, and similar applications. The ultra-bright LEDs available in the market range from Rs 8 to 15. These LEDs...
LED or bulb flickers
This may well be the world's only discreet logic circuit to generate truly random output. It makes an excellent candle flicker light for your Halloween pumpkin and looks much more authentic than a shimmer light wherever a good simulated flame...
relay interfacing with coolrunner ii cpld
The CoolRunner-II board features external 5V relay interfacing, as indicated in the accompanying figure. The ULN2803 is utilized as a driver for the CPLD I/O lines, with the driver outputs connected to the relay modules. A PTB connector is provided...
1A Low Noise High Current LED Torch/Flash
An ultralow dropout current source maintains accurate LED current at very low ILED voltages. Automatic mode switching optimizes efficiency by monitoring the voltage across the LED current source and switching modes only when ILED dropout is detected. The LTC3216 is...
Mains Operated LED Circuit
This is a straightforward and effective LED circuit that can be powered directly from an AC mains supply ranging from 100 volts to 230 volts. The circuit can serve as a mains power indicator or a night lamp. Resistors R1...
mains ac relay module
This mains AC relay module utilizes 5V relays that can be powered directly from an Arduino and can switch 230V. A basic energy monitoring and control system has been constructed using an Arduino 2009, off-the-shelf wireless remote control sockets, and...
1.5V Light emitting diode flasher circuit
With a 1.5V battery supply, the integrated circuit LM3909 can drive the light-emitting diode NSL5027. The 300μF electrolytic capacitor acts as a timing capacitor, which limits the flash speed to approximately 1Hz.
The circuit utilizes the LM3909, a popular LED flasher...
LED Boost Circuit
The completed board may be driven by voltages between 0.8 and 3 Volts. While the basic design goal was candle-like light from a single cell, the values used were chosen to allow safe operation from 3 Volts so you can,...
light flasher/blinker circuit diagram
When the preset is set to its maximum, the LED flashes at a rate of approximately once every half second. This rate can be increased by raising the capacitor value from 10µF to a higher value. For instance, if the...