Led Flasher with a BC547 NPN transistor
Description: This is a novel flasher circuit using a single driver transistor that takes its flash-rate from a flashing LED. The flasher in the photo is 3mm. An ordinary LED will not work. The flash rate cannot be altered by the brightness of the high-bright white LED can be adjusted by altering the 1k resistor across the 100u electrolytic to 4k7 or 10k. The 1k resistor discharges the 100u so that when the transistor turns on, the charging current into the 100u illuminates the white LED. If a 10k discharge resistor is used, the 100u is not fully discharged and the LED does not flash as bright. All the parts in the photo are in the same places as in the circuit diagram to make it easy to see how the parts are connected.
The described flasher circuit utilizes a single driver transistor to control the flashing of a high-brightness white LED. The circuit operates by leveraging the charging and discharging characteristics of a 100µF electrolytic capacitor, which is crucial to the timing of the LED's illumination. The flash rate is inherently linked to the characteristics of the LED being used; specifically, a standard LED is unsuitable for this application, necessitating the use of a high-brightness variant.
In the configuration, a 1kΩ resistor is placed in parallel with the electrolytic capacitor to facilitate its discharge. This resistor plays a critical role in determining the brightness and flash rate of the LED. By adjusting this resistor to higher values, such as 4.7kΩ or 10kΩ, the discharge rate of the capacitor is altered, which in turn affects the flash intensity of the LED. When a higher resistance (like 10kΩ) is employed, the capacitor does not fully discharge, resulting in a dimmer flash from the LED due to insufficient current flow during the charging phase.
The transistor in the circuit acts as a switch, turning on when the capacitor begins to charge. The charging current flows through the LED, causing it to light up. The arrangement of components is critical; each part must be positioned according to the circuit diagram for optimal functionality. This circuit design is effective for applications requiring a simple flashing LED indicator, providing a clear visual signal while allowing for some degree of control over brightness through resistor selection.This is a novel flasher circuit using a single driver transistor that takes its flash-rate from a flashing LED. The flasher in the photo is 3mm. An ordinary LED will not work. The flash rate cannot be altered by the brightness of the high-bright white LED can be adjusted by altering the 1k resistor across the 100u electrolytic to 4k7 or 10k.
The 1k resistor discharges the 100u so that when the transistor turns on, the charging current into the 100u illuminates the white LED. If a 10k discharge resistor is used, the 100u is not fully discharged and the LED does not flash as bright. All the parts in the photo are in the same places as in the circuit diagram to make it easy to see how the parts are connected.
The described flasher circuit utilizes a single driver transistor to control the flashing of a high-brightness white LED. The circuit operates by leveraging the charging and discharging characteristics of a 100µF electrolytic capacitor, which is crucial to the timing of the LED's illumination. The flash rate is inherently linked to the characteristics of the LED being used; specifically, a standard LED is unsuitable for this application, necessitating the use of a high-brightness variant.
In the configuration, a 1kΩ resistor is placed in parallel with the electrolytic capacitor to facilitate its discharge. This resistor plays a critical role in determining the brightness and flash rate of the LED. By adjusting this resistor to higher values, such as 4.7kΩ or 10kΩ, the discharge rate of the capacitor is altered, which in turn affects the flash intensity of the LED. When a higher resistance (like 10kΩ) is employed, the capacitor does not fully discharge, resulting in a dimmer flash from the LED due to insufficient current flow during the charging phase.
The transistor in the circuit acts as a switch, turning on when the capacitor begins to charge. The charging current flows through the LED, causing it to light up. The arrangement of components is critical; each part must be positioned according to the circuit diagram for optimal functionality. This circuit design is effective for applications requiring a simple flashing LED indicator, providing a clear visual signal while allowing for some degree of control over brightness through resistor selection.This is a novel flasher circuit using a single driver transistor that takes its flash-rate from a flashing LED. The flasher in the photo is 3mm. An ordinary LED will not work. The flash rate cannot be altered by the brightness of the high-bright white LED can be adjusted by altering the 1k resistor across the 100u electrolytic to 4k7 or 10k.
The 1k resistor discharges the 100u so that when the transistor turns on, the charging current into the 100u illuminates the white LED. If a 10k discharge resistor is used, the 100u is not fully discharged and the LED does not flash as bright. All the parts in the photo are in the same places as in the circuit diagram to make it easy to see how the parts are connected.
Want To Dim Your LEDs with a TRIAC Dimmer?
LEDs react much faster than conventional bulbs. Light dimmers for standard bulb-based lighting have been in use for many years. The most common implementation of such dimmers...
LEDs, or Light Emitting Diodes, are semiconductor devices that emit light when an electric...
Run through the display circuit equipment Chengdu
Color light-emitting diodes with different colors can indicate the operational status of electrical equipment, as illustrated in the accompanying figure. The red light-emitting diode (LED) R emits red light when energized, indicating that the 220V power supply is functioning normally....
Authentic Looking Knight Rider Led Project
The circuit features red lights that chase up and down on the front of the kit, with a pause of about one second between each sequence. Unlike other circuits that continuously pulse a decade counter, this design employs two 555...
Regency ATC-1 Converter
The 1956 Regency ATC-1 converter marked the beginning of a new era in amateur radio. This compact converter utilized only two transistors—one PNP and one NPN—both made of germanium and now considered obsolete. However, they represented the onset of a...
10 Dancing LEDs ElectronicCircuit Based On The LM358 IC
The following circuit illustrates a Dancing LEDs electronic circuit diagram. This circuit is based on the LM358 integrated circuit. Features: IC1A amplifies the signal.
The Dancing LEDs circuit utilizes the LM358 operational amplifier to create a visually appealing light display. The...
Turning analog inputs into multi-switch digital inputs
There is an interest in creating an interactive LED game board or a "Stargate" DHD-type sci-fi prop, where each tile is illuminated from below by either a single white LED or an RGB combination. The goal is to make each...
10 led VU Meter using LM3915
The circuit diagram represents a straightforward circuit-level indication featuring 10 LEDs. It utilizes a series of half-wave rectification controlled by the precision operational amplifier IC2 TL071. The LM3915 integrated circuit is employed to manage the LEDs, functioning as a VU...
How to connect LED's directly to MAINS
A LED is defined as "light-emitting diode: diode such that light emitted at a p-n junction is proportional to the bias current; color depends on the material used." As the LED is a diode, it doesn't conduct electricity in both...
LED Blown AC Fuse Indicator
LED Blown AC Fuse Indicator Circuit Diagram. This circuit monitors an AC fuse. In this circuit, the LED indicator shows whether or not the fuse is blown.
The LED Blown AC Fuse Indicator Circuit is designed to provide a visual indication...