Flip-Flop Using CMOS NAND Gates
#CMOS
#NAND gate
#flip-flop
#D type
#push-button
#transistor
#logic circuit
#digital electronics
#toggle
Description: Using just two NAND or inverter gates, it is possible to build a D-type (or toggle) flip-flop with a push-button input. At power-up, the output of gate N2 is at a logical 1, ensuring that transistor T2 is switched off. When the push-button is pressed, the output of N2 changes to a logical 0, and transistor T2 conducts. The coupling between N1 and N2 ensures that the output of N1 will always be the inverse of N2, so T1 and T2 will always be in opposite states and will flip each time the push-button is pressed. In some cases, it is possible to omit T1 and T2 and use the outputs of N2 and N1 to drive external circuitry directly, but only if the loading on these outputs is low enough. The 4000 series CMOS family can source/sink a maximum of 0.5 mA (at 5 V), so for safety, it is best to use these open-collector configured transistor buffers. This circuit is particularly useful if there are some unused gates left over in a circuit design, avoiding the need to add a dedicated flip-flop IC. It is worth remembering that all other unused CMOS gates must have their inputs connected to either the positive or ground rail. The supply voltage can be in the range of 3 V to 15 V for CMOS ICs, and the current drawn by this circuit is between 0.2 mA and 5 mA (no load).
The described circuit utilizes two NAND gates or inverters to create a toggle flip-flop configuration, effectively allowing for a simple and efficient method of storing a binary state. The operation begins with the initial state of gate N2 being high (logic 1) at power-up, which keeps transistor T2 in an off state. This configuration ensures that no current flows through T2 until the push-button is activated.
Upon pressing the push-button, the output of N2 transitions to a low state (logic 0), which activates T2 and allows current to flow. The feedback mechanism established between N1 and N2 guarantees that the output of N1 is always the opposite of N2. This complementary behavior causes the flip-flop to toggle its state with each button press, effectively changing the state of T1 and T2 alternately.
While it is feasible to connect external circuits directly to the outputs of N1 and N2, this is only advisable when the load is minimal, as the 4000 series CMOS gates can handle a maximum of 0.5 mA. To ensure reliability and prevent potential damage, it is recommended to use open-collector transistor buffers for higher loads.
Furthermore, when integrating this circuit into a larger design, it is essential to connect any unused CMOS gates to either the positive supply or ground. This practice prevents floating inputs that could lead to unpredictable behavior. The operational voltage for this circuit can range from 3 V to 15 V, making it versatile for various applications, while the current consumption remains low, typically between 0.2 mA and 5 mA under no-load conditions. This circuit design is especially advantageous for applications where space is limited, and existing components can be repurposed, thus eliminating the need for additional flip-flop integrated circuits.Using just two NAND or inverter gates its possible to build a D type (or toggle`)‚ip-‚op with a push-button input. At power-up the output of gate N2 is at a logical 1`, ensuring that transistor T2 is switched off. When the push-button is pressed the output of N2 changes to a logical 0` and transistor T2 conducts. The coupling between N1 and N 2 ensures that the output of N1 will always be the inverse of N2 so T1 and T2 will always be in opposite states and will flip each time the push-button is pressed. In some cases it is possible to omit T1 and T2 and use the outputs of N2 and N1 to drive external circuitry directly but only if the loading on these outputs is low enough.
The 4000 series CMOS family can source/sink a maximum of 0. 5mA (at 5 V) so for the sake of safety its best to use these open-collector congured transistor buffers. This circuit is particularly useful if you have some unused gates left over in a circuit design, avoiding the need to add a dedicated flip-flop IC.
It is worth remembering that all other unused CMOS gates must have their inputs connected to either the positive or ground rail. The supply voltage can be in the range 3 V to 15 V for CMOS ICs and the current taken by this circuit is between 0.
2 mA and 5 mA (no load).
The described circuit utilizes two NAND gates or inverters to create a toggle flip-flop configuration, effectively allowing for a simple and efficient method of storing a binary state. The operation begins with the initial state of gate N2 being high (logic 1) at power-up, which keeps transistor T2 in an off state. This configuration ensures that no current flows through T2 until the push-button is activated.
Upon pressing the push-button, the output of N2 transitions to a low state (logic 0), which activates T2 and allows current to flow. The feedback mechanism established between N1 and N2 guarantees that the output of N1 is always the opposite of N2. This complementary behavior causes the flip-flop to toggle its state with each button press, effectively changing the state of T1 and T2 alternately.
While it is feasible to connect external circuits directly to the outputs of N1 and N2, this is only advisable when the load is minimal, as the 4000 series CMOS gates can handle a maximum of 0.5 mA. To ensure reliability and prevent potential damage, it is recommended to use open-collector transistor buffers for higher loads.
Furthermore, when integrating this circuit into a larger design, it is essential to connect any unused CMOS gates to either the positive supply or ground. This practice prevents floating inputs that could lead to unpredictable behavior. The operational voltage for this circuit can range from 3 V to 15 V, making it versatile for various applications, while the current consumption remains low, typically between 0.2 mA and 5 mA under no-load conditions. This circuit design is especially advantageous for applications where space is limited, and existing components can be repurposed, thus eliminating the need for additional flip-flop integrated circuits.Using just two NAND or inverter gates its possible to build a D type (or toggle`)‚ip-‚op with a push-button input. At power-up the output of gate N2 is at a logical 1`, ensuring that transistor T2 is switched off. When the push-button is pressed the output of N2 changes to a logical 0` and transistor T2 conducts. The coupling between N1 and N 2 ensures that the output of N1 will always be the inverse of N2 so T1 and T2 will always be in opposite states and will flip each time the push-button is pressed. In some cases it is possible to omit T1 and T2 and use the outputs of N2 and N1 to drive external circuitry directly but only if the loading on these outputs is low enough.
The 4000 series CMOS family can source/sink a maximum of 0. 5mA (at 5 V) so for the sake of safety its best to use these open-collector congured transistor buffers. This circuit is particularly useful if you have some unused gates left over in a circuit design, avoiding the need to add a dedicated flip-flop IC.
It is worth remembering that all other unused CMOS gates must have their inputs connected to either the positive or ground rail. The supply voltage can be in the range 3 V to 15 V for CMOS ICs and the current taken by this circuit is between 0.
2 mA and 5 mA (no load).
touch switch circuit with 3 transistors
This document describes a series of touch switches that utilize only three transistors. These touch-based transistor switches can activate a load simply by the user touching a metal plate. They are designed to directly switch a relay, enabling operation with...
Night security light
This simple circuit is built around a CMOS IC 4060 to obtain the required timing. During daytime, the LDR has low resistance and keeps pin 12 of IC1 high, preventing IC1 from oscillating. When it is dark, the LDR resistance...
ECM Mic Preamplifier
Both transistors should be low noise types. In the original circuit, BC650C was used, which is an ultra-low noise device. These transistors are now hard to find, but BC549C or BC109C are good replacements. The circuit is self-biasing and will...
Transistor circuit of a pressure gauge
To ensure proper operation of the transistor in a circuit, it is essential to measure the reverse breakdown voltage of the transistor. This is particularly important for tubes with high reverse breakdown voltage requirements, such as those used in OCL...
Single-junction transistor sine wave oscillator circuit
The single-junction transistor is commonly utilized in sawtooth and pulse generators, and it can also be configured to create a basic sine wave generation circuit. As an oscillator circuit composed of discrete components, it requires a minimal number of parts....
The Transistor Amplifier-P2
The three circuits described provide a constant current to the LED (or LEDs) when the supply voltage reaches 15V or higher. The second and third circuits can be activated or deactivated through the input line by turning on the top...
The time delay circuit diagram composed of transistor
The circuit is designed to set a delay time based on the voltage Us and the resistor R. In this configuration, S1 acts as the discharge switch for capacitor C. When switch S1 is closed, the stored charge in capacitor...
Single-junction transistor sine wave oscillator circuit
The single-junction transistor is commonly utilized in sawtooth and pulse generators, and it can also be configured to create a basic sine wave generation circuit. As an oscillator circuit composed of discrete components, it requires a minimal number of parts....
ICL7665S CMOS Micropower Over/Under Voltage Detector
The ICM7226 is a fully integrated Universal Counter and LED Display driver. It combines a high-frequency oscillator, a decade timebase counter, an 8-decade data counter and latches, a 7-segment decoder, digit multiplexer, and segment and digit drivers, which can directly...