relay driver board project
Description: This article aims to utilize an old PC as a simple controller. Many outdated PCs, such as the 8088, 8086, 80286, 80386, or even 80486, have become obsolete systems. This design employs an 8-bit LPT printer parallel data port (DP) to activate relays. The LPT printer parallel port also has a 4-bit additional port (PC) that can be utilized, although this is not implemented in the design as 8 bits are deemed sufficient. This size (1 byte) is compatible with each of the 8255 PPI ports if interfacing is desired. The basic principle is the same for all eight channels. To protect the LPT port from damage, an optocoupler is used to isolate the PC side (+5V) from the relay circuit (+24V). The relay voltage type can be adjusted to +12V or even +6V if suitable relays are available. The PC914 optocoupler can be replaced with other types from the 4N series (4N22 to 4N28, 4N35, 4N47 to 4N49, etc.). A common driver configuration involving transistors Q1 to Q8 (high-power) is used to drive the relays. Diodes D1 to D8 protect the transistors from transient currents when the relays are in the off state. Resistor values are chosen to ensure that the transistors are sufficiently saturated when turned on. This common driver can also be replaced with IC drivers such as ULN2002 to ULN2004 types, which contain 6-bit line drivers per package, necessitating two ICs for full utilization. It is important to select relays that can withstand high voltage and current if they are to be used for AC line equipment. Caution is advised regarding high-voltage lines on the PCB. The component specifications include: R1 to R16 = 10k (16 pcs), R17 to R24 and R33 = 1.5k (9 pcs), R25 to R32 = 1k (8 pcs), C1 = 2200 µF/50V (1 pc), C2 = 1000 µF/25V (1 pc), D1 to D12 = 1N4007 (12 pcs), LED1 to LED9 = Red LED (3 mm) (9 pcs), IC1 = 7824 (voltage regulator) (1 pc), Q1 to Q8 = C1061 (transistor) (8 pcs), OP1 to OP8 = PC914 (optocoupler) (8 pcs), RL1 to RL8 = 24V PCB type relay (high-power output, 5A/220V-AC) (8 pcs), CON1 = DB-25 socket (female, PCB type, LPT connector) (1 pc), optional CON2 = power connector (1 pc), OUT-1 to OUT-8 = 2-pairs of terminal strips (8 pcs), transformer = 15V with CT/1A or 30V-AC/1A (1 pc), optional on/off switch for power supply (1 pc), optional LPT parallel port cable (3 m) (1 pc), optional small heatsink for voltage regulator (1 pc).
This schematic describes a practical approach to repurposing outdated PC hardware into a functional relay controller. The design leverages the LPT port for data output, allowing the control of multiple relays through a straightforward interface. The use of optocouplers ensures electrical isolation, thus protecting the sensitive components of the PC from potential damage due to high-voltage spikes from the relay circuit.
The circuit's architecture is based on a modular design, where each channel operates independently, enhancing reliability and ease of troubleshooting. The inclusion of diodes for transient protection is essential in preventing back EMF from damaging the driving transistors. The selection of high-power transistors ensures that the relays can be activated without risking overheating or failure.
In terms of component selection, the use of common, readily available parts like the 7824 voltage regulator and the 1N4007 diodes simplifies sourcing and assembly. The recommended relay specifications ensure compatibility with various AC loads, making the controller versatile for different applications. Additionally, the optional components, such as the heatsink and power switch, provide further customization and efficiency enhancements.
Overall, this design provides a cost-effective solution for controlling devices using legacy PC technology, making it an excellent project for electronics enthusiasts and those looking to extend the life of older computing hardware.This article means to utilize your old PC to be come a simple controller. Many old PC like 8088 type, 8086, 80286, 80386, or even 80486 already become an obsolete systems. This board using 8-bits of LPT printer parallel data port (DP) to activate the relays. LPT printer parallel port also have 4-bits additional port (PC) which can be utilized too. But this is not implemented in this design, because in my opinion, 8-bits are more than enough, and beside that this size (1 byte) fit each of 8255 PPI port if we want to interface it too. The basic is the same for all the eight channels. To protect the LPT port from damage, I use optocoupler to isolated the PC side (+5V) and relay circuit (+24V).
You can change the relay voltage type to +12V or even +6V if you can find one. This type of optocoupler, PC914 can be replaced with another type like 4N series (4N22 ~ 4N28, 4N35, 4N47 ~ 4N49, etc. ). Using a common driver combination, transistor Q1 ~ Q8 (hi-power) to drive the relays. D1 ~ D8 use to protect the transistor from any transient current when the relay is in the off state. The resistor values are chosen to make transistors get full enough saturated when it is on. This common driver also can be change using IC driver like: ULN2002 ~ ULN2004 types. Each package contain 6-bits line drivers. So you need 2 of this IC, but one does not maximize. If you use PC port, than this IC can be utilized. A good alternative. Note that, for the relays, it must be stand the high voltage and current (big power) if you want to use it to drive any equiptment from the AC line.
Find a good ones with a high rating output. Careful about the hi-voltage line on the PCB. R1 ~ R16 = 10k. 16 pcs R17 ~ R24, R33 = 1k5. 9 pcs R25 ~ R32 = 1k. 8 pcs C1 = 2200 uF/50V (elco). 1 pcs C2 = 1000 uF/25V (elco). 1 pcs D1 ~ D12 = 1N4007. 12 pcs Led1 ~ Led9 = Red Led (3 mm). 9 pcs IC1 = 7824 (voltage regulator). 1 pcs Q1 ~ Q8 = C1061 (transistor). 8 pcs OP1 ~ OP8 = PC914 (optocoupler). 8 pcs RL1 ~ RL8 = 24V relay PCB type (hi-power output, 5A/220V-AC). 8 pcs CON1 = DB-25 socket (female, PCB type, LPT connector). 1 pcs Optional CON2 = power connector. 1 pcs OUT-1 ~ OUT-8 = 2-pairs of terminal strip. 8 pcs Transformer = 15V with CT/1A or 30V-AC/1A. 1 pcs Optional on/off switch for power supply. 1 pcs Optional LPT parallel port cable (3 m). 1 pcs Optional little heatsink for voltage regulator. 1 pcs
This schematic describes a practical approach to repurposing outdated PC hardware into a functional relay controller. The design leverages the LPT port for data output, allowing the control of multiple relays through a straightforward interface. The use of optocouplers ensures electrical isolation, thus protecting the sensitive components of the PC from potential damage due to high-voltage spikes from the relay circuit.
The circuit's architecture is based on a modular design, where each channel operates independently, enhancing reliability and ease of troubleshooting. The inclusion of diodes for transient protection is essential in preventing back EMF from damaging the driving transistors. The selection of high-power transistors ensures that the relays can be activated without risking overheating or failure.
In terms of component selection, the use of common, readily available parts like the 7824 voltage regulator and the 1N4007 diodes simplifies sourcing and assembly. The recommended relay specifications ensure compatibility with various AC loads, making the controller versatile for different applications. Additionally, the optional components, such as the heatsink and power switch, provide further customization and efficiency enhancements.
Overall, this design provides a cost-effective solution for controlling devices using legacy PC technology, making it an excellent project for electronics enthusiasts and those looking to extend the life of older computing hardware.This article means to utilize your old PC to be come a simple controller. Many old PC like 8088 type, 8086, 80286, 80386, or even 80486 already become an obsolete systems. This board using 8-bits of LPT printer parallel data port (DP) to activate the relays. LPT printer parallel port also have 4-bits additional port (PC) which can be utilized too. But this is not implemented in this design, because in my opinion, 8-bits are more than enough, and beside that this size (1 byte) fit each of 8255 PPI port if we want to interface it too. The basic is the same for all the eight channels. To protect the LPT port from damage, I use optocoupler to isolated the PC side (+5V) and relay circuit (+24V).
You can change the relay voltage type to +12V or even +6V if you can find one. This type of optocoupler, PC914 can be replaced with another type like 4N series (4N22 ~ 4N28, 4N35, 4N47 ~ 4N49, etc. ). Using a common driver combination, transistor Q1 ~ Q8 (hi-power) to drive the relays. D1 ~ D8 use to protect the transistor from any transient current when the relay is in the off state. The resistor values are chosen to make transistors get full enough saturated when it is on. This common driver also can be change using IC driver like: ULN2002 ~ ULN2004 types. Each package contain 6-bits line drivers. So you need 2 of this IC, but one does not maximize. If you use PC port, than this IC can be utilized. A good alternative. Note that, for the relays, it must be stand the high voltage and current (big power) if you want to use it to drive any equiptment from the AC line.
Find a good ones with a high rating output. Careful about the hi-voltage line on the PCB. R1 ~ R16 = 10k. 16 pcs R17 ~ R24, R33 = 1k5. 9 pcs R25 ~ R32 = 1k. 8 pcs C1 = 2200 uF/50V (elco). 1 pcs C2 = 1000 uF/25V (elco). 1 pcs D1 ~ D12 = 1N4007. 12 pcs Led1 ~ Led9 = Red Led (3 mm). 9 pcs IC1 = 7824 (voltage regulator). 1 pcs Q1 ~ Q8 = C1061 (transistor). 8 pcs OP1 ~ OP8 = PC914 (optocoupler). 8 pcs RL1 ~ RL8 = 24V relay PCB type (hi-power output, 5A/220V-AC). 8 pcs CON1 = DB-25 socket (female, PCB type, LPT connector). 1 pcs Optional CON2 = power connector. 1 pcs OUT-1 ~ OUT-8 = 2-pairs of terminal strip. 8 pcs Transformer = 15V with CT/1A or 30V-AC/1A. 1 pcs Optional on/off switch for power supply. 1 pcs Optional LPT parallel port cable (3 m). 1 pcs Optional little heatsink for voltage regulator. 1 pcs
Relay Driver with Strobe
The LM111 comparator can be utilized to design a relay driver with a TTL strobe, which enhances control over the relay driver. The strobe signal can be used to manage the relay operation more effectively.
The LM111 is a high-speed voltage...
8-bit bus control widely used 12-bit DA converter Universal
The 8 microcomputer data operates with an 8-bit parallel output, while also accommodating serial input for D-A converters. Typically, data must be entered in two groups and processed as a whole. The requirements for data latching involve 16 straight odd...
PC parallel port Null Printer Adapter
This circuit is a simple adapter for PC parallel port to think that there is a printer connected to computer. This adapter is useful for testing printing speed with different software and as a part of your own designs. You...
Synchronous controller circuit diagram of a recording transcript
Modern exhibitions utilize extensive sound, light, and electrical technologies for advertising, promotion, and propaganda. This involves various electrical diagrams and control models. Commonly used is an automatic program circuit with pre-recorded commentary, which requires synchronization of two mating times. A...
Parallel Port Interfacing and Programming
In interfacing AC loads, isolation is crucial. An interfaced circuit that does not isolate the computer from the AC load risks significant damage to the computer if the interfaced circuit fails or is destroyed. Isolation can be achieved using a...
PC home light control system
This project describes a new economical solution of home light control systems. The presented home light control system can be used for different sophisticated home applications. The control system consists of a PC, and control circuitry and the electrical devices....
Control electrical appliances using PC
Control electrical appliances using a PC. This circuit utilizes the printer port of a PC for control applications through software and some interface hardware. The interface circuit is included.
The described circuit leverages the parallel printer port (also known as LPT...
OSU8 Microprocessor Project (1994)
OSU8 began as a student project in 1994 to create a simple but functional 8-bit microprocessor, starting with a definition of the architecture to implementation in a Xilinx FPGA chip, and full-custom CMOS implementation. Over a period of about six...
Parallel port programming
The delay timing setting of the program will depend on the CPU speed. The timing delay can be utilized from the C+ library, allowing the standard timing to be set on any computer, with a minimum achievable time delay of...