LCD to LPT board
#LCD
#LPT
#IR remote control
#backlight control
#contrast control
#DS1809
#push buttons
#transistor
#Lirc
Description: The LCD2LPT with Lirc circuit is the compilation of two circuits found on the net on a single board. The first is LCD to LPT interface and the second an IR remote control interface using http://www.lirc.org program. The main circuit for LCD connection to LPT was modified adding a backlight and contrast control using 4 push buttons. Responsible for the adjustment are the two DS1809 ICs made from Dallas-Maxim semiconductors along with 2 buttons for each adjustment. IC1 with the use of S1(+, Up) and S2(-, Down) controls the Contrast of LCD and IC2 with the use of S3(+, Up) and S4(- , Down) and the help of transistor T1, controls the backlight intensity. More: IC3 is a 7805 regulator that stabilize the power line of the circuit. There is also a filtering capacitor that helps the transient discharge of the circuit preventing any damages to the ICs.
To JP2 you must apply 12V and if you wish you can add a polarity protection diode (1N4007).
For the IR receiver you must read the site http://www.lirc.org. The only thing i have to add up is to remove pin3 during contraction and read the receiver's IC datasheet to help you out connecting it right. An adaptor for the LCD is also included so you can use a ribbon cable for the connection with the main circuit.
The LCD2LPT with Lirc circuit integrates an LCD to LPT interface and an infrared (IR) remote control interface on a single PCB. The LCD interface employs a modified design that incorporates backlight and contrast control, facilitated through four push buttons. The DS1809 integrated circuits (ICs) from Dallas-Maxim semiconductors are central to this functionality, with two dedicated buttons for each adjustment. The first IC (IC1) manages the contrast of the LCD, utilizing push buttons S1 (for increasing contrast) and S2 (for decreasing contrast). The second IC (IC2) governs the backlight intensity, using buttons S3 and S4, and is augmented by a transistor (T1) to effectively control the brightness levels.
Power regulation for the circuit is handled by a 7805 voltage regulator (IC3), which ensures a stable 5V output necessary for the operation of the LCD and associated components. Additionally, a filtering capacitor is included in the design to mitigate transient voltage spikes, thereby protecting sensitive ICs from potential damage.
For power supply, a 12V input is required at the JP2 connector. To enhance circuit protection, the inclusion of a polarity protection diode, such as the 1N4007, is recommended.
The IR remote control functionality is designed to work with the LIRC software, which can be accessed for additional setup instructions. It is crucial to remove pin 3 during construction and to consult the datasheet of the IR receiver IC to ensure correct wiring and functionality. Furthermore, an adapter for the LCD is provided, allowing for a straightforward connection using a ribbon cable to integrate with the main circuit seamlessly.The "LCD2LPT with Lirc" circuit is the compilation of two circuits found on the net on a single board. The first is LCD to LPT interface and the second an IR remote control interface using http://www.lirc.org program.
The main circuit for LCD connection to LPT was modified adding a backlight and contrast control using 4 push buttons. Responsible for the adjustment are the two DS1809 ICs made from Dallas-Maxim semiconductors along with 2 buttons for each adjustment.
IC1 with the use of S1(+, Up) and S2(-, Down) controls the Contrast of LCD and IC2 with the use of S3(+, Up) and S4(- , Down) and the help of transistor T1, controls the backlight intensity. IC3 is a 7805 regulator that stabilize the power line of the circuit. There is also a filtering capacitor that helps the transient discharge of the circuit preventing any damages to the ICs. To JP2 you must apply 12V and if you wish you can add a polarity protection diode (1N4007). For the IR receiver you must read the site http://www.lirc.org. The only thing i have to add up is to remove pin3 during contraction and read the receiver's IC datasheet to help you out connecting it right.
An adaptor for the LCD is also included so you can use a ribbon cable for the connection with the main circuit.
To JP2 you must apply 12V and if you wish you can add a polarity protection diode (1N4007).
For the IR receiver you must read the site http://www.lirc.org. The only thing i have to add up is to remove pin3 during contraction and read the receiver's IC datasheet to help you out connecting it right. An adaptor for the LCD is also included so you can use a ribbon cable for the connection with the main circuit.
The LCD2LPT with Lirc circuit integrates an LCD to LPT interface and an infrared (IR) remote control interface on a single PCB. The LCD interface employs a modified design that incorporates backlight and contrast control, facilitated through four push buttons. The DS1809 integrated circuits (ICs) from Dallas-Maxim semiconductors are central to this functionality, with two dedicated buttons for each adjustment. The first IC (IC1) manages the contrast of the LCD, utilizing push buttons S1 (for increasing contrast) and S2 (for decreasing contrast). The second IC (IC2) governs the backlight intensity, using buttons S3 and S4, and is augmented by a transistor (T1) to effectively control the brightness levels.
Power regulation for the circuit is handled by a 7805 voltage regulator (IC3), which ensures a stable 5V output necessary for the operation of the LCD and associated components. Additionally, a filtering capacitor is included in the design to mitigate transient voltage spikes, thereby protecting sensitive ICs from potential damage.
For power supply, a 12V input is required at the JP2 connector. To enhance circuit protection, the inclusion of a polarity protection diode, such as the 1N4007, is recommended.
The IR remote control functionality is designed to work with the LIRC software, which can be accessed for additional setup instructions. It is crucial to remove pin 3 during construction and to consult the datasheet of the IR receiver IC to ensure correct wiring and functionality. Furthermore, an adapter for the LCD is provided, allowing for a straightforward connection using a ribbon cable to integrate with the main circuit seamlessly.The "LCD2LPT with Lirc" circuit is the compilation of two circuits found on the net on a single board. The first is LCD to LPT interface and the second an IR remote control interface using http://www.lirc.org program.
The main circuit for LCD connection to LPT was modified adding a backlight and contrast control using 4 push buttons. Responsible for the adjustment are the two DS1809 ICs made from Dallas-Maxim semiconductors along with 2 buttons for each adjustment.
IC1 with the use of S1(+, Up) and S2(-, Down) controls the Contrast of LCD and IC2 with the use of S3(+, Up) and S4(- , Down) and the help of transistor T1, controls the backlight intensity. IC3 is a 7805 regulator that stabilize the power line of the circuit. There is also a filtering capacitor that helps the transient discharge of the circuit preventing any damages to the ICs. To JP2 you must apply 12V and if you wish you can add a polarity protection diode (1N4007). For the IR receiver you must read the site http://www.lirc.org. The only thing i have to add up is to remove pin3 during contraction and read the receiver's IC datasheet to help you out connecting it right.
An adaptor for the LCD is also included so you can use a ribbon cable for the connection with the main circuit.
Common emitter amplifier works a
A common emitter amplifier functions as a signal amplification unit by utilizing a common emitter configuration, which inverts the output signal. This operation can be analyzed by observing the input signal waveform. During the first quarter of the period, the...
L7136 LCD Thermometer For Vehicle Engine
Function: Used to measure the voltage change minute by management before the temperature diodes. Component: IC, Diode, Resistor, 3-1/2 digit LCD (SP521PR).
The circuit described functions as a voltage measurement system designed to monitor minute voltage changes, particularly in relation to...
Transistor Buffer for Zener Diode Voltage Regulator
Buffering for the zener diode is achieved through the impedance matching and current amplifying features of the emitter follower, which draws less current from the zener.
Buffering in electronic circuits is essential for ensuring that the performance of one component does...
One 2N2222 Transistor Code Lock
The circuit consists of a basic transistor switch with a relay connected at its collector as the load. This represents a straightforward electronic code lock circuit that employs a single transistor.
The circuit operates by utilizing a transistor as a switch...
improved 3 transistor audio amp
This circuit is similar to the previous one but employs positive feedback to enhance the amplitude delivered to the speaker. It is adapted from a small 5-transistor radio that utilizes a 25-ohm speaker. In the earlier circuit, the load resistor...
Common emitter amplifier circuit resistance and capacitance coupled basic
Common emitter amplifier circuit with resistance and capacitance coupling.
The common emitter amplifier circuit is a fundamental configuration in analog electronics, widely utilized for its ability to amplify voltage signals. This circuit employs a bipolar junction transistor (BJT) as the active...
A Transistor Based Single Zone Alarm circuit
The circuit includes automatic exit and entry delays, a timed bell cut-off, and a system reset feature. It accommodates both normally-open and normally-closed switches, making it compatible with standard input devices such as pressure mats, magnetic reed contacts, foil tape,...
Reverse Bias Oscillators
Several NPN transistors can oscillate within the audio frequency range when reverse biased. The minimum supply voltage required is 7V for low-power transistors like the BC109, BC238, and 2N2222A; it increases to 12V for medium-power transistors such as the BD139,...
Three single junction transistor time relay circuits
This circuit consists of three single-junction transistor time relay circuits utilizing a pulse charging mechanism, allowing for extended delay times of up to several minutes. The first stage delay circuit incorporates unijunction transistors (VTi) and other components, where capacitor C1...