LCD Module Control with PC
#LCD
#PC control
#parallel port
#2-line display
#16-character display
#printer port
#module control
#interface circuit
Description: This simple circuit controls a popular 2-line x 16-character LCD by a PC via printer port. It doesn't use the Bi-directional feature found on newer printer ports, thus it should work with most, if not all, Parallel Ports. These LCD Modules are very common these days and are quite simple to work with, as all the logic required to run them is on board. More: The LCD panel's Enable and Register Select is connected to the Control Port. The Control Port is an open collector/open drain output. While most Parallel Ports have internal pull-up resistors, there are a few which don't. Therefore by incorporating the
The circuit described is designed to interface a 2-line by 16-character Liquid Crystal Display (LCD) with a personal computer through a parallel printer port. The parallel port serves as a communication interface, allowing data and control signals to be sent from the PC to the LCD module. The circuit does not utilize the bi-directional capabilities of modern printer ports, making it compatible with a wide range of older parallel ports.
The LCD module operates using a set of control signals, specifically the Enable (E) and Register Select (RS) pins, which are essential for its operation. In this configuration, the Enable pin is responsible for signaling the LCD when to read the data present on the data pins, while the Register Select pin determines whether the data being sent is command data or character data. Both of these pins are connected to the Control Port of the parallel interface.
The Control Port is configured as an open collector or open drain output. This configuration allows multiple devices to be connected to the same line without risk of contention, as the output can only pull the line low, and an external pull-up resistor is required to pull the line high when not driven low. While many parallel ports include internal pull-up resistors, some do not, which necessitates the incorporation of external pull-up resistors in the circuit to ensure proper operation.
The data pins of the LCD are typically connected to the data lines of the parallel port, allowing for the transmission of character data. The circuit may also include additional components such as resistors and capacitors to stabilize the power supply and filter noise, ensuring reliable operation of the LCD module.
Overall, this circuit is a practical solution for displaying text from a PC on a standard LCD module, leveraging the simplicity and accessibility of the parallel printer port interface. The design is particularly useful for applications where a low-cost and straightforward display solution is required.This simple circuit controls a popular 2-line x 16-character LCD by a PC via printer port. It doesn't use the Bi-directional feature found on newer printer ports, thus it should work with most, if no all Parallel Ports. These LCD Modules are very common these days, and are quite simple to work with, as all the logic required to run them is on board.
The LCD panel's Enable and Register Select is connected to the Control Port. The Control Port is an open collector / open drain output. While most Parallel Ports have internal pull-up resistors, there are a few which don't. Therefore by incorporating the
The circuit described is designed to interface a 2-line by 16-character Liquid Crystal Display (LCD) with a personal computer through a parallel printer port. The parallel port serves as a communication interface, allowing data and control signals to be sent from the PC to the LCD module. The circuit does not utilize the bi-directional capabilities of modern printer ports, making it compatible with a wide range of older parallel ports.
The LCD module operates using a set of control signals, specifically the Enable (E) and Register Select (RS) pins, which are essential for its operation. In this configuration, the Enable pin is responsible for signaling the LCD when to read the data present on the data pins, while the Register Select pin determines whether the data being sent is command data or character data. Both of these pins are connected to the Control Port of the parallel interface.
The Control Port is configured as an open collector or open drain output. This configuration allows multiple devices to be connected to the same line without risk of contention, as the output can only pull the line low, and an external pull-up resistor is required to pull the line high when not driven low. While many parallel ports include internal pull-up resistors, some do not, which necessitates the incorporation of external pull-up resistors in the circuit to ensure proper operation.
The data pins of the LCD are typically connected to the data lines of the parallel port, allowing for the transmission of character data. The circuit may also include additional components such as resistors and capacitors to stabilize the power supply and filter noise, ensuring reliable operation of the LCD module.
Overall, this circuit is a practical solution for displaying text from a PC on a standard LCD module, leveraging the simplicity and accessibility of the parallel printer port interface. The design is particularly useful for applications where a low-cost and straightforward display solution is required.This simple circuit controls a popular 2-line x 16-character LCD by a PC via printer port. It doesn't use the Bi-directional feature found on newer printer ports, thus it should work with most, if no all Parallel Ports. These LCD Modules are very common these days, and are quite simple to work with, as all the logic required to run them is on board.
The LCD panel's Enable and Register Select is connected to the Control Port. The Control Port is an open collector / open drain output. While most Parallel Ports have internal pull-up resistors, there are a few which don't. Therefore by incorporating the
Parallel port controls arbitrary-waveform generator
You can use the parallel port of your PC and a few additional components to generate a powerful, easy-to-use arbitrary-waveform generator. By using a Visual Basic program with the circuit in Figure 1, you can generate any waveform (for example,...
Crystal display (LCD) tester
Liquid crystal displays (LCDs) are available in various versions and sizes. The wide variety of features has led to some confusion regarding pin configurations. Consequently, even after extensive searching for a suitable screen, users often encounter difficulties in utilizing it....
Interfacing LCD via SPI
Over time, microcontrollers have become increasingly powerful, cost-effective, and compact. A typical microcontroller from the past may have had 40 pins and lacked internal memory, whereas modern J-series PICs feature 96K of program memory and only 28 pins. This allows...
LCD 7 digit HF counter
The resistor between basis and collector (around 47k) is to be individually set according to transistor characteristics. Without PIC in socket at the collector should be 2.5 V.
The circuit described involves a transistor configuration where a resistor, typically valued at...
schematic how to write data on lcd
In the project, the LCD data ports are connected to port 1 of the controller, while the control pins, namely RS, E, and R/W, are connected to pins 3, 5, 6, and 2, 1 of the controller. The LCD is...
PC based Robot Circuit
To create the circuitry described, a computer software capable of controlling a parallel port is required, with an estimated cost of approximately $30. For instance, a transistor (model number 2N2222) is priced around $0.50, while a DPDT relay costs about...
Build your own LC-Display
For the wiring of the display, the ribbon cable is first taken and soldered according to the circuit diagram on the 25-pin sub-D (parallel port) plug. The small circuit diagram illustrates the rear side, which is the solder side of...
Filaments Detection Circuit
LCD modules have become a popular means of displaying system messages and status in embedded applications. This application note demonstrates how to interface an SST FlashFlex microcontroller to a typical character LCD module. The SST FlashFlex is an industry-standard, 8051-compatible...
Simple Parallel (Printer) Port Interface
This is the basic interface I used as part of my Computerized Room project. This is the parallel interface only. The 8 bit input card can be found, along with the rest of the project, at Computerize Your Room/House. This...