Solar cell battery charger circuit
#solar cell
#9-V battery
#astable multivibrator
#push-pull TMOS
#Schmitt trigger
#full wave bridge rectifier
#filament transformer
#180 Hz
#30 mA
Description: The circuit charges a 9-V battery at approximately 30 mA per input ampere at 0.4 V. U1, a quad Schmitt trigger, operates as an astable multivibrator to drive push-pull MOSFET devices Q1 and Q2. Power for U1 is derived from the 9-V battery via D4, while power for Q1 and Q2 is supplied by the solar cell. The multivibrator frequency, determined by R2 and C1, is set to 180 Hz for maximum efficiency from a 6.3-V filament transformer, T1. The secondary of the transformer is connected to a full-wave bridge rectifier, D1, which is linked to the batteries being charged. The small Ni-Cad battery serves as a fail-safe excitation supply, allowing the system to recover if the 9-V battery becomes fully discharged. A CdS photocell disables the oscillator in darkness to preserve the fail-safe battery during shipping, storage, or prolonged periods of darkness.
The described circuit functions as a solar-powered battery charger for a 9-V battery, utilizing a combination of a Schmitt trigger, MOSFETs, and a transformer-based rectification system. The key component, U1, is configured as an astable multivibrator, generating a square wave output that alternates between high and low states. This oscillation drives the MOSFETs Q1 and Q2 in a push-pull configuration, allowing for efficient switching and control of the power delivered to the load.
The power supply for U1 is sourced from the 9-V battery, which is essential for the operation of the Schmitt trigger and ensures that the control circuit remains functional during the charging process. Diode D4 serves to isolate the power supply for U1 from the output, protecting the circuit from potential back-feeding and ensuring stable operation.
The solar cell provides the necessary input power for the MOSFETs, enabling them to switch on and off rapidly at the frequency set by the resistor R2 and capacitor C1. The choice of 180 Hz for the multivibrator frequency is optimized for the characteristics of the 6.3-V filament transformer, T1, which steps down the voltage for rectification. The secondary winding of T1 feeds into a full-wave bridge rectifier composed of diode D1, converting the alternating current (AC) output from the transformer into direct current (DC) suitable for charging the 9-V battery.
To enhance the reliability of the system, a small Ni-Cad battery is included as a fail-safe measure. This battery provides a backup power source for the circuit, ensuring that it can recover and continue functioning if the primary 9-V battery is fully depleted. The incorporation of a CdS photocell adds an additional layer of protection; it monitors ambient light levels and disables the oscillator when darkness is detected. This feature helps conserve the charge in the fail-safe battery during shipping, storage, or extended periods without light, thus prolonging the operational lifespan of the system.
Overall, the circuit design effectively combines renewable energy sources with robust battery management features, making it suitable for applications where reliable battery charging is essential.The circuit charges a 9-V battery at about 30 mA per input ampere at 0.4 V. Ul, a quad Schmitt trigger, operate as an astable multivibrator to drive push-pull TMOS devices Ql and Q2. Power for Ul is derived from the 9-V battery via D4; power for Ql and Q2 is supplied by the solar cell.
The multivibrator frequency, determined by R2-C1, is set to 180 Hz for maximum efficiency from a 6.3-V filament transformer, Tl. The secondary of the transformer is applied to a full wave bridge rectifier, Dl, which is connected to the batteries being charged.
The small Ni-Cad battery is a fail-safe excitation supply to allow the system to recover if the 9-V battery becomes fully discharged. A CdS photocell shuts off the oscillator in darkness to preserve the fail-safe battery during shipping and storage, or prolonged darkness.
The described circuit functions as a solar-powered battery charger for a 9-V battery, utilizing a combination of a Schmitt trigger, MOSFETs, and a transformer-based rectification system. The key component, U1, is configured as an astable multivibrator, generating a square wave output that alternates between high and low states. This oscillation drives the MOSFETs Q1 and Q2 in a push-pull configuration, allowing for efficient switching and control of the power delivered to the load.
The power supply for U1 is sourced from the 9-V battery, which is essential for the operation of the Schmitt trigger and ensures that the control circuit remains functional during the charging process. Diode D4 serves to isolate the power supply for U1 from the output, protecting the circuit from potential back-feeding and ensuring stable operation.
The solar cell provides the necessary input power for the MOSFETs, enabling them to switch on and off rapidly at the frequency set by the resistor R2 and capacitor C1. The choice of 180 Hz for the multivibrator frequency is optimized for the characteristics of the 6.3-V filament transformer, T1, which steps down the voltage for rectification. The secondary winding of T1 feeds into a full-wave bridge rectifier composed of diode D1, converting the alternating current (AC) output from the transformer into direct current (DC) suitable for charging the 9-V battery.
To enhance the reliability of the system, a small Ni-Cad battery is included as a fail-safe measure. This battery provides a backup power source for the circuit, ensuring that it can recover and continue functioning if the primary 9-V battery is fully depleted. The incorporation of a CdS photocell adds an additional layer of protection; it monitors ambient light levels and disables the oscillator when darkness is detected. This feature helps conserve the charge in the fail-safe battery during shipping, storage, or extended periods without light, thus prolonging the operational lifespan of the system.
Overall, the circuit design effectively combines renewable energy sources with robust battery management features, making it suitable for applications where reliable battery charging is essential.The circuit charges a 9-V battery at about 30 mA per input ampere at 0.4 V. Ul, a quad Schmitt trigger, operate as an astable multivibrator to drive push-pull TMOS devices Ql and Q2. Power for Ul is derived from the 9-V battery via D4; power for Ql and Q2 is supplied by the solar cell.
The multivibrator frequency, determined by R2-C1, is set to 180 Hz for maximum efficiency from a 6.3-V filament transformer, Tl. The secondary of the transformer is applied to a full wave bridge rectifier, Dl, which is connected to the batteries being charged.
The small Ni-Cad battery is a fail-safe excitation supply to allow the system to recover if the 9-V battery becomes fully discharged. A CdS photocell shuts off the oscillator in darkness to preserve the fail-safe battery during shipping and storage, or prolonged darkness.
Schmitt trigger with programmable hysteresis
The CA 3088 is utilized as a versatile Schmitt trigger. The magnitude of the hysteresis levels is determined by the current (Ia) flowing out of the amplifier's output and through resistor R2. An increase in Ia results in an increase...
Solar Cell Voltage Regulator
This device is designed to serve as a simple and cost-effective comparator, intended for use in a solar cell power supply system where a quick indication of either too low or acceptable voltage is required. The circuit includes one 5V...
Starting Network for Astable Multivibrator
An astable multivibrator is a flip-flop that produces two unstable states (high and low), functioning as an oscillator.
An astable multivibrator is a fundamental electronic circuit that continuously switches between its two states without requiring any external triggering signals. This...
Astable multivibrator IIV
The circuit features independent control of "ON" and "OFF" periods and employs the CA3130 BiMOS operational amplifier for various applications, including filters, oscillators, and long-duration timers. It operates with an input current of 50 pA, allowing oscillators to utilize large...
Schmitt trigger
By replacing the common-emitter resistor in a conventional Schmitt trigger circuit with a Zener diode, the hysteresis typically associated with these circuits is eliminated.
In a conventional Schmitt trigger, the hysteresis is introduced by the feedback mechanism involving the common-emitter resistor,...
Mosquito repelant circuit
The Astable Multivibrator, which is generally used as a signal generator, is once again used here to generate the desired frequencies. It is an excellent example of the fact, how versatile simple basic electronic circuit can be. It seems quite...
direct coupled discrete astable
This flip-flop circuit is a free-running astable multivibrator, with the bases and collectors of both emitter-biased transistors directly coupled to each other. The switching action is facilitated by a capacitor in each emitter circuit. This configuration produces triangular waves at...
Schmitt trigger
The lower trigger point is fixed at a percentage of Vcc, while the upper trigger point can be adjusted using Pin 5, allowing it to vary from Vi to slightly less than Vcc. The Schmitt trigger is capable of operating...
Solar Cell Voltage Regulator circuit
This device is designed to be a simple, inexpensive comparator intended for use in a solar cell power supply setup where a quick indication of "too low" or "just right" voltage is needed. The circuit consists of one 5V regulator,...