Cat / Dog Detector
Description: This can be used to control entry on a Cat or Dog Door. NOTE: There may be some changes and improvements coming. However, this circuit does work and you can build it as shown. The PCB shown below is available from me, or make it yourself. It measures 2.75" by 1.1". This circuit uses one tuned coil for on the door and just a single wire loop on the animal's collar. When the two coils come close together, it produces a signal that can cause an LED to light and also trips a solenoid to unlock the door so it can open. Since all these doors are somewhat different, I leave the solenoid and mechanical parts of this design for you to figure out.
The main advantage of this unit is that it does not require any battery on the animal, as is the case with most store-bought devices for this purpose. The single-turn coil can be joined with plugs so it can be removed easily. However, if the plug comes apart or has a poor connection, the door won't open. Therefore, it is better to make the coil just barely big enough to slip over the animal's head and solder it to make a solid loop, then tape it to the animal's collar. The larger the diameter of this coil, the greater the sensitivity will be. Additionally, it is important that the cat or dog door and the surroundings do not contain any large pieces of metal. This circuit also functions as a metal detector, and this detector sees the single loop of wire as a solid piece of metal. Furthermore, the coil on the door needs to be mounted in such a way that the coil on the animal can actually get almost inside the coil on the door. A round or rectangular extension outward from the door may be needed to accomplish this. Ideally, the coil on the door will have an inductance of about 150 µH. An inductance calculator can determine this for a round coil.
This circuit operates by using electromagnetic induction to create a signal when the two coils are in proximity. The tuned coil on the door is designed to resonate at a specific frequency, which is achieved by selecting the appropriate inductance and capacitance values. When the animal approaches the door, the single wire loop on its collar, which acts as a secondary coil, couples with the primary coil on the door. This coupling generates a voltage in the primary coil, which can be used to activate an LED indicator and a solenoid mechanism.
The solenoid, which is responsible for unlocking the door, requires careful selection to ensure that it operates effectively with the generated signal. The design should account for the physical characteristics of the door and the solenoid's power requirements. Additionally, the PCB layout should accommodate the tuned circuit components, ensuring minimal interference and optimal performance.
For optimal function, the installation of the coils should be done with precision. The coil on the door should be positioned such that it allows for maximum coupling with the collar loop. This may require adjustments in the mounting position or the use of extensions to facilitate the necessary proximity. The overall effectiveness of the system can be influenced by environmental factors, including the presence of metallic objects nearby, which may interfere with the electromagnetic field.
In conclusion, this circuit provides a practical solution for controlling access through a pet door without the need for batteries on the animal. Proper construction and installation are essential for reliable operation, and attention to the physical placement of components will enhance the system's performance.This can be used to control entry on a Cat or Dog Door" NOTE: There may be some changes and improvements coming. However this circuit does work and you can build it as shown. The PCB Shown below is Available from me, or make it yourself. It Measures 2.75" by 1.1". This circuit uses one tuned coil for on the door and just a single wire loop on the animals collar. When the two coils come close together, it produces a signal that can cause a an LED to light and also trips a solenoid to unlock the door so it can open.
Since all these doors are somewhat different, I leave The Solenoid and Mechanical Parts of this design for you to figure out. The Main Advantage of this unit is it does Not Require any Battery on the animal, as is the case with most store bought devices for this purpose. The Single turn coil can be joined with plugs so it can be removed easly. But if the plug comes apart or has a poor connection, the door won't open. So Better yet, make it Just Barely big enough to slip over the animals head, and Solder it to make a solid loop, than tape it to the animals collar.
And the Larger the diameter of this coil, the Greater the Sensivity will be. Also Important, the Cat or Dog door and the surroundings "Can't contain any large pieces of metal". (This circuit is also a Metal Detector and This detector see's the Single Loop of wire as a solid piece of metal.) Additionally, the coil on the door needs to be mounted in such a way that the coil on the animal can actually get almost inside the coil on the door. Possibly a Round or Rectangular Extension, outward from the door will be needed to accomplish this. Either way, the coil on the door will probably need to be mounted a few inches from the door. Ideally the coil on the door will have an inductance of about 150 uH. My Inductance calculator can determine this for a Round Coil.
The main advantage of this unit is that it does not require any battery on the animal, as is the case with most store-bought devices for this purpose. The single-turn coil can be joined with plugs so it can be removed easily. However, if the plug comes apart or has a poor connection, the door won't open. Therefore, it is better to make the coil just barely big enough to slip over the animal's head and solder it to make a solid loop, then tape it to the animal's collar. The larger the diameter of this coil, the greater the sensitivity will be. Additionally, it is important that the cat or dog door and the surroundings do not contain any large pieces of metal. This circuit also functions as a metal detector, and this detector sees the single loop of wire as a solid piece of metal. Furthermore, the coil on the door needs to be mounted in such a way that the coil on the animal can actually get almost inside the coil on the door. A round or rectangular extension outward from the door may be needed to accomplish this. Ideally, the coil on the door will have an inductance of about 150 µH. An inductance calculator can determine this for a round coil.
This circuit operates by using electromagnetic induction to create a signal when the two coils are in proximity. The tuned coil on the door is designed to resonate at a specific frequency, which is achieved by selecting the appropriate inductance and capacitance values. When the animal approaches the door, the single wire loop on its collar, which acts as a secondary coil, couples with the primary coil on the door. This coupling generates a voltage in the primary coil, which can be used to activate an LED indicator and a solenoid mechanism.
The solenoid, which is responsible for unlocking the door, requires careful selection to ensure that it operates effectively with the generated signal. The design should account for the physical characteristics of the door and the solenoid's power requirements. Additionally, the PCB layout should accommodate the tuned circuit components, ensuring minimal interference and optimal performance.
For optimal function, the installation of the coils should be done with precision. The coil on the door should be positioned such that it allows for maximum coupling with the collar loop. This may require adjustments in the mounting position or the use of extensions to facilitate the necessary proximity. The overall effectiveness of the system can be influenced by environmental factors, including the presence of metallic objects nearby, which may interfere with the electromagnetic field.
In conclusion, this circuit provides a practical solution for controlling access through a pet door without the need for batteries on the animal. Proper construction and installation are essential for reliable operation, and attention to the physical placement of components will enhance the system's performance.This can be used to control entry on a Cat or Dog Door" NOTE: There may be some changes and improvements coming. However this circuit does work and you can build it as shown. The PCB Shown below is Available from me, or make it yourself. It Measures 2.75" by 1.1". This circuit uses one tuned coil for on the door and just a single wire loop on the animals collar. When the two coils come close together, it produces a signal that can cause a an LED to light and also trips a solenoid to unlock the door so it can open.
Since all these doors are somewhat different, I leave The Solenoid and Mechanical Parts of this design for you to figure out. The Main Advantage of this unit is it does Not Require any Battery on the animal, as is the case with most store bought devices for this purpose. The Single turn coil can be joined with plugs so it can be removed easly. But if the plug comes apart or has a poor connection, the door won't open. So Better yet, make it Just Barely big enough to slip over the animals head, and Solder it to make a solid loop, than tape it to the animals collar.
And the Larger the diameter of this coil, the Greater the Sensivity will be. Also Important, the Cat or Dog door and the surroundings "Can't contain any large pieces of metal". (This circuit is also a Metal Detector and This detector see's the Single Loop of wire as a solid piece of metal.) Additionally, the coil on the door needs to be mounted in such a way that the coil on the animal can actually get almost inside the coil on the door. Possibly a Round or Rectangular Extension, outward from the door will be needed to accomplish this. Either way, the coil on the door will probably need to be mounted a few inches from the door. Ideally the coil on the door will have an inductance of about 150 uH. My Inductance calculator can determine this for a Round Coil.
Audio 10 LED VU meter
The circuit was designed to work with an audio power amplifier which operated off +18v-0v-18v power rails. The actual voltage used is not too critical except that the feedback is referred to the LED chain which itself is anchored to...
Search Light Signal
This circuit controls a searchlight-type signal head and produces solid red, yellow, or green indications. The signals can be connected for normal or approach-type lighting of the green signal. The circuit utilizes an LM556 dual timer IC in a complementary...
Flashing Eyes
This circuit is designed as a humorous Halloween gadget. It is intended to be placed at the back of a badge or pin featuring a typical Halloween character image, such as a pumpkin, skull, black cat, witch, or ghost. Two...
Electronic Birthday Candle
The concept involves mounting a microphone on a stick with an LED and designing a circuit that responds to loud noises detected by the microphone input (such as blowing) to turn off the LED. The schematic is straightforward, powered by...
LED or Lamp Flasher
Flashing frequency can be varied by changing R1 value in the 1M - 4M7 range. This circuit is very efficient when driving a small 3.2V incandescent lamp. In this case omit the LED and R3, connecting the bulb across Q2...
led table reading lamp circuit
This LED table or reading lamp circuit can be utilized for various applications, such as a reading lamp for a bed, a desktop or table lamp, a keyboard lamp (to illuminate the keys of a computer keyboard in low light),...
Color Sensor from a Reversed LED and Op Amp
One of the first lessons that electronics students learn is that an LED emits light when current flows through it. However, it is also true that when an LED is connected in reverse, it can generate a current flow when...
power led flasher
The low-cost and compact circuit presented here serves as a highly power-saving flashing LED indicator. While most LEDs typically fail to operate below 2 volts, with a forward voltage of at least 1.6 volts, this flasher can function using a...
low volt led flasher schematics
In the circuit diagram for the Joule Thief, the common point of the toroid is the connection at the top of the hand-wound ferrite toroid, located in the upper right of the diagram. This connection leads to the positive terminal...